In a scenario where a platform harbours multiple interrupts to the
extent the core cannot support it, an interrupt controller is added
as an additional level of interrupt. It typically combines several
sources of interrupt into one line that is then routed to the parent
controller.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
It makes no sense to set the restart condition flag on a first message
and some i2c bus drivers (like the stm32 v1 driver) actually reject
them by returning an error from i2c_transfer().
This patch fixes that by using i2c_burst_read() in tmp112_reg_read()
instead. For consistency, tmp112_reg_write() is also changed to use
i2c_burst_write().
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
I have been using this the TMP112 driver with success with a TMP102
connected to to nucleo-f411re board (via I2C1 using PB8/9).
According to the datasheets, both devices are both driver and pin
compatible although the TMP102 is less accurate.
This temperature sensor is not a thermopile sensor type as stated in
comments.
This patch updates that help info
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Write protection is currently not supported by the mcux flash
driver. This prevents it from working with the DFU subsystem, which
checks the error codes from the write protect routine. Hack it for now
with a semaphore.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Add support for AMS CCS811 Digital Gas Sensor for monitoring
indoor air quality. This sensor reports the following parameters:
1. Co2 concentration
2. VOC concentration
3. Sensor voltage
4. Sensor current
This driver only supports polling mode as of now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Most of sensor channels defined by Zephyr use the main, unscaled
SI unit. We also have SENSOR_CHAN_ALTITUDE which is defined in
meters. So, it only makes sense to define distance in meters too
The only driver supporting SENSOR_CHAN_DISTANCE as of now is
vl53l0x.c, which was updated accordingly. Also, update doc links
in the driver based on the review comment.
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This patches fixes a few bugs with the SAM0 driver:
- txrx was trasnmitting too many bytes
- adds support for NULL buffers to the fast paths
- fixes a NULL dereference on the rx buffer slow path
The tests under tests/driver/spi/spi_loopback now pass.
Signed-off-by: Michael Hope <mlhx@google.com>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Add Altera Nios-II QSPI Flash controller driver which has
has 1024 blocks or sectors wich each sector size being 64K bytes.
This driver supports flash erase, write, read and lock operations.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Based on the discussion in #5693, the reason why humidity was defined
in milli-percent was likely following Linux which defines it as such
in its sensor subsystem:
http://elixir.free-electrons.com/linux/latest/source/Documentation/ABI/testing/sysfs-bus-iio#L263
However, Linux defines temperature in milli-degrees either, but
Zephyr uses degrees (similarly for most other quantities). Typical
sensor resolution/precision for humidity is also on the order of 1%.
One of the existing drivers, th02.c, already returned values in
percents, and few apps showed it without conversion and/or units,
leading to confusing output to user like "54500".
So, switching units to percents, and update all the drivers and
sample apps.
For few drivers, there was also optimized conversion arithmetics
to avoid u64_t operations. (There're probably more places to
optimize it, and temperature conversion could use such optimization
too, but that's left for another patch.)
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Now the native console driver also handles stdin
so we can drive the shell from the command line,
a pipe or a file
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Driver is 'Busy' can be a warning message which can be enabled with
minimum debug level CONFIG_SYS_LOG_IEEE802154_DRIVER_LEVEL=2.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Some mcu's have USART_PRESC_PRESCALER defined in the function call. Add
a prescaler of div1 to it.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
The default PWM polarity was 'inversed', which is not aligned with the
other PWM drivers. Unfortunately there is not yet an API to define the
default polarity to be used by the driver, but assume that 'normal'
(signal starts high for the duration of the duty cycle) should be the
default.
Signed-off-by: Ricardo Salveti <ricardo@opensourcefoundries.com>
Uses the new flash erase-block-size dts property to implement the flash
page layout api in the mcux flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the max30101 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxas21002 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxos8700 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Current buffers might be configured to skip data, thus only len will be
set, buf will be NULL. Buffer should be used if only len is > 0 and
buffer is valid as well.
tx/rx are "on" if len is > 0
tx/rx buf should be touched if only len is > 0 _and_ buf != NULL.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move to new Kconfig pattern in which we use an if !HAS_DTS_I2C_DEVICE
block for the Kconfig symbols that can now come from DT generation.
This pattern is useful to allow us to define default values for the
generated symbols for build-all testing.
Fixes: #5877
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Transfer is an important concept of USB specification.
During a transfer, several packets can be transmitted.
Today the usb API only provides ep_read and ep_write
functions but the transfer concept is missing.
This is typically ok for basic drivers which don't have
to take care of how data is transfered/splitted.
However there are some drivers like CDC EEM, in which
transfer concept is important for packet management.
Moreover, current ep-write and ep_read method have a
different implementation in usb_dc_dw and usb_dc_stm32
device drivers. For example usb_dc_dw supports only
1-data-packet transfers due to its implementation.
This can increase latency and reduce performance.
I think this is something we need to fix/improve by
implementing better transfer management.
This patch introduces usb_dc_ ep_transfer method which
can be used to configure IN/OUT transfers. This allows
to configure and request different transfer sizes and
should prevent usage of the current stm32 temporary
buffer.
This method has asynchronous and synchronous mode.
Synchronous mode waits for transfer completion before
returning. Asynchronouse mode (irq safe) configures
the transfer and returns immediately, the provided
callback will be then called on transfer completion.
This also update ep_write and ep_read stm32 implementation
to use this new method but keep their behavior unchanged
for legacy reasons.
Note that for now this method is local to stm32 device
driver, however the goal would be to expose this function
as a new USB device driver API method so that class
drivers use it. This will request same implementation in
the usb_dc_dw_driver.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
usb mass example need usb_dc_ep_read_wait/continue API.
test usb mass storage with RAM DISK on stm32f4 series.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Move to use an if HAS_DTS_I2C_DEVICE instead of depends on so that the
Kconfig sybmols don't even show up if HAS_DTS_I2C_DEVICE is true.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds pinmux defines to use I2C2 at PB10/PB11 for
stm32f0-based boards.
Needed for stm32f072b_disco board to use extension
connector
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
We want to move to use a common FLASH_DEV_NAME across the various flash
drivers. So samples, tests, or other code can be a bit more generic. So
replace CONFIG_SOC_FLASH_NRF5_DEV_NAME with FLASH_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove SoCs part dependency of CLOCK_STM32_PLL_PREDIV1 config since
it will only be used on parts having an HSE oscillator, ignored
otherwise.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The shared irq support doesn't really require its own dir, lets merge it
into drivers/interrupt_controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The generic library provided by ST in ext/hal/st/lib/sensor/vl53l0x
needs to be adapted to the platform. In this case, the main
modification is the way to use I2C. This is now using the Zephyr
I2C API.
Signed-off-by: Vincent Veron <vincent.veron@st.com>
Add driver for ST vl53l0x time of flight sensor.
This driver can be used in 2 modes :
* proximity sensor :
configure VL53L0X_PROXIMITY_THRESHOLD
will return 1 if target is between sensor and threshold,
else, 0
* distance sensor :
will return the distance in millimeters from sensor to target
This driver use the official STMicroelectronics library for vl53l0x.
(in ext/hal/st/lib/sensor/vl53l0x)
Signed-off-by: Vincent Veron <vincent.veron@st.com>
Add gpio mcux driver which can be used for lpcxpresso54114 and other lpc
socs. In this driver, CMSIS register access is made for GPIO.
Option for access by GPIO Pin is provided as of now.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add usart-yaml in dts.
Build fsl_lpc_usart and fsl_lpc_flexcomm in
ext/hal/nxp/mcux/drivers/Makefile.
Only polling mode is implemented in usart now. Interrupt can be added in
future.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new pinmux driver for lpcxpresso54114 based on mcux.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use "select USE_STM32_LL_SPI" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_LL_USB/USE_STM32_HAL_PCD/USE_STM32_HAL_PCD_EX"
to select the needed STM32 HAL files, instead of editing
ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_LL_RNG" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_HAL_TIM" to select the needed STM32 HAL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_LL_I2C" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_HAL_ETH" to select the needed STM32 HAL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_LL_UTILS" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The CMakeLists lost the config for uart_mcux_lpsci.c, which is the
console driver for board frdm_kl25z. So just add "uart_mcux_lpsci.c"
into drivers/serial/CMakeLists.txt to make it work.
Signed-off-by: Jason Wang <jason.yanping.wang@hotmail.com>
In flash driver init, write_block_size could be initialized
with FLASH_WRITE_BLOCK_SIZE which is generated from device
tree parsing (dts property: "write-block-size")
Fixes#5305
If not defined, generate a compilation error.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
CC1200 is a sub-ghz chip supporting 6 ISM & SRD bands: 169, 433, 470,
868, 915 and 920 MHz, with features dedicated to IEEE 802.15.4(g).
Current driver enables CC1200 against actual IEEE 802.15.4 Soft-MAC. 'g'
version support in the Soft-MAC will follow later.
The chip itself is closer to a bare metal radio modem than to a usual
15.4 chip: up to the user to provide the right RF settings for the
carrier band. Such settings can be generaten through TI's SmartRF tool.
Hopefully, for channel selection, this driver will be clever enough to
compute the proper register change without any special input from the
user. This will work for all the bands supported by the chip.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Wrong buffer assigned for receiving the last 2 bytes in multi
byte reception of STM32F4 i2c driver. Change the buffer to
correct one.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This reverts commit 2a7efb7419.
"choice" section in board Kconfig.defconfig introduces a dependency
from the sensor to the board. As a consequence a warning was generated
whenever the sensor was used on another board.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This reverts commit 2e20f49167.
"choice" section in board Kconfig.default introduces a dependency
from the sensor to the board. Then a warning was generated
whenever the sensor is used on another board
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The SAM0 series has up to 6 SPI ports. Add Kconfig options to match.
Similar to the 9033fb2f01, this patch
only defines the fields that are currently used and skips ones like
GPIO and IRQ priority that aren't.
Signed-off-by: Michael Hope <mlhx@google.com>
It appears the STM32F411XE doesn't support RNG so remove enabling it
from the SoC defconfig and flag an error if attempting to build the
driver on that SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
According to STM32F4 reference manual, software should wait for BTF=1
before reading N-2 data byte.
Reference:
"For N >2 -byte reception, from N-2 data reception" section, page
853 of STM32F4 Reference manual.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The SAM0 has a 64 byte page (the programing unit) with 4 pages to a
row (the erase unit). This driver implements a read/modify/write to
emulate the byte level writes used by NFFS.
Signed-off-by: Michael Hope <mlhx@google.com>
In STM32 family, RNG IP is available only on F4 and L4 series.
Besides STM32F401 does not support is neither.
Get entropy driver available on STM32 devices supporting it and
generate a compilation issue on STM32 devices that do not own
the RNG IP.
Solves #5448
Signed-Off-By: Erwan Gouriou <erwan.gouriou@linaro.org>
On STM32L4 SoCs RNG is clocked by 48MHz domain.
Hence, besides clock activation, it requires 48M
domain to be enabled.
Tested on:
*nucleo_l476rg
*stm32l476g_disco
*disco_l475_iot1
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
SPI_MODE_GET() returns a bitfield. It is thus wrong to test if a bit is
set using the equality operator. The bit-wise AND operator must be used
instead.
This can be tested by setting the SPI in mode 3 (CPOL + CPHA). Currently
both tests will fail and the result is a SPI configured in mode 0. This
was confirmed using an oscilloscope. Applying the patch fixes the
polarity.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
