PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Mutable driver state relocated from config_info to driver_info. This
driver supports PCI enumeration. We drop code that attempts to update
irq_num based on PCI enumeration because the interrupt found by PCI
enumeration must always be the same as the statically configured IRQ
number.
Change-Id: I5580b0ba95635696a825fe66dbf16259c54d5ba8
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
The driver performs one shot PHY setup. There is no support for PHY
disconnect, reconnect or configuration change. The PHY setup,
implement via KSDK contains polled code that can block the
initialization thread for a few seconds.
There is no statistics collection for either normal operation or error
behaviour.
Origin: Original
Change-Id: Ia0f2e89a61348ed949976070353e823c178fcb24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Generalize the LOG_ETHERNET_LEVEL configuration parameter for use with
multiple ethernet drivers.
Change-Id: I26bc2189c8cf79db19f59e8082caec03b0d9c7b8
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This reverts commit 581e15ced2.
The commit was marked RFC and should not have been merged yet.
Change-Id: Iafd3587f8840e64670c32fa5726ea20ac9c9962a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
This driver is functional, just. It is not in a fit state to be merged to master yet.
Origin: Original
Change-Id: Id29e756f33c6c0263926139188c49f9a9c3d5e09
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The driver originally gets the full-duplex configuration
from the PHCON1 register and PDPXMD bit as stated by the
ENC298J60 specification document section 2.6 "LED Configuration".
This section trust the board to LEDB connection to signal the
full-duplex configuration.
This commit gets the full-duplex configuration from Kconfig
symbols to allow a proper functionality even when the board
is not connecting LEDB apropriately.
Change-Id: I803958409a611e23e2c3e03f40b412f1695947af
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
There is a tx semaphore that controls a single access to the
transmission service. The device is capable to manage a single
transmission call at a time. Multiple requests need to wait
for the resource to be free.
This commit adds the initial release to the tx semaphore.
Jira: ZEP-895
Change-Id: Ic9879cfd15bb1494644b2cf0f4565f7e6a2c1c22
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
ENCC28J60 specs section 6.5 "MAC Initialization settings"
state that MACON3(7:5) register configure automatic padding and CRC.
It also states that the configuration 111 and 011 both configure as
all short frames to be zero padded with a valid CRC appended.
Nevertheless, experimentally, there are ocassions when configuring as 111
frames does not have a CRC appended. This frames could be rejected
by the receiver if it is configured to do so.
This commit changes configuration from 111 to 011, which is not
presenting that behavior.
Jira: ZEP-842
Change-Id: I302bb99f7a1f23b298fe0db0245963b640644040
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Per spec document, RXEN bit corresponds to bit 2
of the ECON1 register instead of bit 1.
Change-Id: I1bbfd048be248575a558679985ba9daadc43df0e
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
The rx fiber call contiki IP stack functions to register
received frames. This interaction requires more stack memory
in the rx fiber stack to avoid memory corruption.
Change-Id: I106339e7dd1ca9282426adfb54590e34297755b3
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
SPI bus is a shared resource between tx and rx processes.
The access to it must be synchronized to allow a rx process to
happen even when a tx process is taking place.
ECON1 register must be saved by the rx process and recovered
at the end to ensure that the tx process will continue operating
in the same register bank.
Change-Id: Ie9358bf02bef8ddb5bdf76c8847e998a627e5395
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
Transmision status is polled. Remove rx interruption enabling and
clearance.
Change-Id: I2893f89533adef5f77c711a36b5c1bbe21c48a23
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
Even values in ERXRDPT register may corrupt the receive buffer.
Set ERXRDPT value one address behind the next value.
If it is zero, set the value to the reception buffer end address.
Change-Id: I7150e5190c5bfb7bfafbff598eea1c26959643d0
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
The Receive Packet Pending Interrupt Flag (EIR.PKTIF) does not
reliably/accurately report the status of pending packets.
Reception fails intermittently. The EPKTCNT register is used instead.
Change-Id: I599c3b4df1b74d769dd7104e5c6e253d9cf63bd4
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
Adds the ENC28J60 Ethernet module driver.
Origin: Original
JIRA: ZEP-291
Change-Id: I2b5790ecb251f9059f172bcaafadef24bd27207a
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Created menu for Ethernet driver and moved driver + debugging setting
under it. Changed prompt from "Grove log level" to more describing and
fixed typos.
Change-Id: If2f79fee1a002a42e89e2493a2294332abec05ee
Signed-off-by: Jani Pajarinen <jani.pajarinen@intel.com>
The ethernet driver generates a lot of spurious interrupts.
These spurious interrupts have two sources:
1) The Mac Management Counter (MMC) module generates a lot of interrupts
(GMI - bit 27 of the status register). Unfortunately the Interrupt
enable register doesn't allow us to enable/disable it (bit 27 is
reserved). Therefore the only way to mask this interrupt is to mask
all the MMC interrupts (register REG_MMC_RX_INTR_MASK,
REG_MMC_TX_INTR_MASK and REG_MMC_RX_IPC_INTR_MASK). By default
these interrupts are not masked.
2) The RX interrupt is not correctly acknowledged. According to the
datasheet, NIS is a sticky bit and must be cleared (by writing 1
to this bit) each time a corresponding bit, which causes NIS to
be set, is cleared.
Change-Id: I2033973849d87cddc328c65d0d4ad36b5a0c934e
Signed-off-by: Sebastien Griffoul <sebastien.griffoul@intel.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ib483419be5199b52cf281b4b106cd8a3be95b7be
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
When an ethernet frame is larger than UIP_BUFSIZE,
a net_buf is allocated but never released. Therefore
after few bad frames, no more RX network packet
can be received.
Fixed by allocating the net_buf after checking
the frame length.
Change-Id: I436487e3c26d739de347b4db6facc3a3dbebbe75
Signed-off-by: Sebastien Griffoul <sebastien.griffoul@intel.com>
This patch replaces all occurences of the macro DEV_NOT_CONFIG by
-EPERM at the driver level. This patch is part of the effort to
transition from DEV_* codes to errno.h codes.
Change-Id: I3054c8aa76319a58a2eec089b8a72bf301c85391
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
got the following compilation error when trying
to compile the Synopsys DesignWare Ethernet driver:
In file included from drivers/ethernet/eth_dw.c:25:0:
drivers/ethernet/eth_dw_priv.h:27:28:
fatal error: contiki/ip/uip.h: No such file or directory
Fixed by adding correct include path in ethernet
Makefile
Change-Id: I8ea50e3ffb89e54349140de124f68d196a412f8e
Signed-off-by: Jean-Paul Etienne <jean-paul.etienne@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
It's not a function and requires all its arguments to be build-time
constants. Make this more obvious to the end user to ease confusion.
Change-Id: I64107cf4d9db9f0e853026ce78e477060570fe6f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename them to DEVICE_NAME_GET and DEVICE_GET to fit in the 'device'
namespace.
Change-Id: I407a7f284ed4d1c071961b46615eea859c2e825f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds extern "C" { } blocks to header files so that they can be
safely used by C++ source files.
Change-Id: Ia4db0c36a5dac5d3de351184a297d2af0df64532
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The interrupt API has been redesigned:
- irq_connect() for dynamic interrupts renamed to irq_connect_dynamic().
It will be used in situations where the new static irq_connect()
won't work, i.e. the value of arguments can't be computed at build time
- a new API for static interrupts replaces irq_connect(). it is used
exactly the same way as its dynamic counterpart. The old static irq
macros will be removed
- Separate stub assembly files are no longer needed as the stubs are now
generated inline with irq_connect()
ReST documentation updated for the changed API. Some detail about the
IDT in ROM added, and an oblique reference to the internal-only
_irq_handler_set() API removed; we don't talk about internal APIs in
the official documentation.
Change-Id: I280519993da0e0fe671eb537a876f67de33d3cd4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Rename class in pci_dev_info struct to allow to use C++ compilers.
Updated drivers to use new struct.
Change-Id: I17b94cb7bc094bccd615c8389a28589bfa90cab8
Signed-off-by: Javier B Perez Hernandez <javier.b.perez.hernandez@linux.intel.com>
PROJECTINCLUDE is not required in app makefiles.
Change-Id: I3751b7c51c453dfe47d207bb11d171138668c4e7
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removes the 'priority' parameter from the IRQ_CONFIG macro.
This parameter was not used anymore in any architecture.
The priority is handled in the IRQ_CONNECT macro.
The documentation is updated as well.
Change-Id: I24a293c5e41bd729d5e759113e0c4a8a6a61e0dd
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Put initialization priorities as device driver Kconfig
parameter.
Initialization priority value for each platform is defined
in the platform Kconfig file.
Drivers and platform code use SYS_DEFINE_DEVICE to add
and initialization function.
Change-Id: I2f4f3c7370dac02408a1b50a0a1bade8b427a282
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not depend on environment variables and use a kconfig variable
for defining the architecture.
In addition, remove the X86_32 variable, it just duplicates X86 for
not good reason, at least until start supporting MCUs with 64bit.
Change-Id: Ia001db81ed007e6a43f34506fed9be1345b88a4b
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch adds a driver for a Synopsys DesignWare Ethernet MAC. The
driver uses interrupts to handle received frames, but it uses a
spinloop when transmitting to wait for the transmit descriptor to
become available. Transmission is coordinated by a fiber, so this
should not result in the system execution being blocked. Only a
single descriptor is allocated for each of the transmit and receive
directions to save memory and simplify the code. Another
simplification is that none of the offload capabilities of the
Ethernet device are used. The driver currently only supports a single
instance of the Ethernet MAC, which is consistent with the limitation
in the network stack that only a single network device is supported.
Change-Id: I013b3d439a76e8ff91a775516f7035841b040870
Signed-off-by: Michael LeMay <michael.lemay@intel.com>
