Update the hal_nordic module revision to include the following commits:
- CMakelists: missing "src" in one path
- nrfx_glue: Fix NRFX_PPI_GROUPS_USED_BY_BT_CTLR definition
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update hal_stm32 module in master manifest to include
latest changes around License information
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support for the SX126x series of LoRa radios using the
LoRaMAC-Node HAL.
This driver currently makes the following assumptions:
* DIO1 is used as an interrupt line.
* There is an RF switch selecting between the TX and RX ports and
that switch is controlled by DIO2.
* There is either no TCXO or the TCXO is controlled by DIO3.
Specifically, the limitations above mean that modules that use GPIOs
to control the RF switch are currently not supported. Support for such
modules would need changes to the LoRaMAC-Node code.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Add initial support for nuvoton numicro m48x SoC series, basic
init and uart functionality are covered with gpio and clock
directly relies on HAL.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Some options were available in the options.cmake but were not reflected
in Kconfig.
Added possibility to enable additional configuration options for OT.
Some of the options were left commented out as those options are not
yet supported e.g. require Thread 1.2 or require shim changes.
As openthread has gazillion configuration options that are passed as
define value, created generic option for passing any number of those
values separated with space.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Reference an updated head that removes references to reporting
infrastructure when reporting is disabled.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
According to RM, when increasing the CPU frequency, the new number of
wait states to the Flash latency bits must be written and verified
before modifying the CPU clock source and/or the CPU clock prescaler,
to prevent NMI to occur; when decreasing the CPU frequency, after.
Tested with STM32L462 SOC and MSI with several frequencies, both
increasing and decreasing. HSE built, not tested.
Signed-off-by: Giancarlo Stasi <giancarlo.stasi@nexxiot.com>
Update the STM32 HAL to include the stm32l0xx_ll_usb HAL in the
build. This enables USB device support on STM32L0 devices.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Building a couple more files from the SimpleLink SDK in order to support
the ieee8021504 driver for CC13xx/CC26xx.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Update hal_nordic to fix compilation issue with nrfx_nvmc, compilation
issue for NRF_UICR not defined in non-secure build.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
fixes#24706
Fixed issue of possible try to erase non page aligned
size of flash while serving image write command.
The new version has this bug fixed.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Update the hal_nordic module revision, so that the following commit
becomes effective:
nrf_radio_802154: Use chosen zephyr,entropy to get entropy device
Use the label property of the node pointed by "zephyr,entropy" chosen
entry as the name of the entropy device to bind to. The pointed node
does not necessarily need to be a "nordic,nrf-rng" compatible one, what
was incorrectly assumed when CONFIG_ENTROPY_NAME was replaced in commit
5505d0baa66a89848f643120fafad232876df695.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This should fix an issue with setting labels. A label was renamed and
ci-tools did not handle the error.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commits adds a config option to build a PSA trusted-firmware-m
(TF-M) application image for the secure processing environment, and
configures the Zephyr application image for the non-secure processing
environment. The secure and non-secure environment images will be
linked together via the veneer function table that is produced as an
artifact of the TF-M build process.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add infineon xmc series with XMC4500 support. XMC series comes with,
- CPU operates upto 120MHz
- 3 RAM (PSRAM1 - code, DSRAM1 - data and DSRAM2 - communiation)
- upto 1MB flash
init: clock control & gpio is not done, so SoC initialization directly
relies on HAL. Core operating clock is stored in no_init section, which
is kept under DSRAM1. Only DSRAM1 is used until clock support. Using
PSRAM1 and DSRAM1 needs adaptation in linker script - planned for next
revision.
Note: SystemInit cannot be consumed directly due to vector table +
HAL linker dependency.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Fixed masking defines for eSPI OOB RX and TX transfer
length registers. The transfer length fields are 13 bit.
The incorrect defines masked 14 bits.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Both ST and STM32 modules where using same HAS_STLIB Kconfig
symbol.
Now that each module is createing is own lib, we need to be able
to distinguish libs.
Depends on zephyrproject-rtos/hal_stm32/pull/52
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move syst initialization code to zephyr tree and add
more useful fields (payload length and timestamp) in
SyS-T message packet.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Update mbedTLS commit along with the following fixes:
* Fix naming inconsistencies in some cipher modes, to match core mbedTLS
configs
* Add Kconfig to enable CTR cipher mode
Fixes#22421
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Update west.yml to point to hal_ti with the latest changes
from TI SimpleLink SDK 4.10.00.78 for CC13x2/CC26x2.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Update the TI HAL module so that it points to a revision that has been
ported to the new timeout API.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This is to update west.yml to point to hal_ti with the latest changes
from TI SimpleLink SDK 4.10.00.07 for CC32xx.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
As part of devicetree update to new devicetree.h We Need to convert
as use of DT_ARM_CORTEX_M4F_CLOCK_FREQUENCY to
DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency) in the hal_ti for the
msp432p4xx SoCs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update STM32WB HCI lib support to version 1.5.0.
Additionally provide a doc section to clarify compatibility
with stm32wb wireless co-processor binaries.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Start SOCKS5 proxy in the net-tools Docker image and run MQTT TLS
tests with SOCKS enabled. Since the MQTT TLS server is already
running as of the previous test, start only the danted daemon.
Rely on mosquitto MQTT port being handled by the Docker image
configuration file instead of specifying it on the command line.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Updating west.yml to point a fix to include proper time.h header in
the HAL. This should fix an issue where clock_gettime() is not
correctly called due to recent change to make it into a system call.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
