Fix compilation issue for extended advertising beacon. Adv pool was
mistakenly put under BT_OBSERVER define.
Both observer and broadcaster use the bt_lookup_id_addr. SMP cannot
be enabled without connections, so for broadcaster and observer there
will not be a lookup.
Fix compilation warning for extended scanner-only build.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
According to the BT Core spec. The local RPA field in the enhanced
connection complete event should be set if the own-address type was
set to 0x02/0x03 and the controller generated an RPA using a non-zero
IRK, otherwise the controller should return all zeroes.
In the case where we generate the RPA in the host instead we need to
handle set the on-air RPA address based on the random address set by
the host.
If this is not handled then pairing will fail because the on-air
addresses are used as input to the pairing procedure.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove handling of extended advertising from connection complete
event. If extended advertising has been enabled and is supported by
the controller then enhanced connection complete must be supported.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
User of bt_buf_get_rx may attempt to push their own headers, e.g. ACL
headers, so move the H4 header logic to bt_recv after logging into the
monitor since otherwise the buffer would contain H4 headers which is
not expected by the monitor.
Fixes#24646
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for multiple advertising set. Move the advertising state
flags to be per advertising set and loop over advertising sets instead
of looking up legacy advertiser set or handle 0.
Since it is not certain that the advertising set terminated event can
arrive directly after the connection complete event there is currently
a limitation that there can only be one local identity used by
connectable advertisers at a time. This guarantees that we know
the local identity being used in the connection complete event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Only attempt to restart the background scanner in connection complete
event when the new connection is a master role connection or the
initiator was successfully canceled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Enable enhanced connection complete when extended advertising has been
enabled. This event is mandatory if extended advertising is supported.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This makes hci_raw to manage RX and TX buffers so its logic don't have
to be replicated on each an every driver/application, it also makes it
simpler to deal with extra headers for H:4 mode since that then can be
done at earlier at buffer allocation.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for registering a command extention table which is
used to match incoming commands and then pass the buffer to its
function handler.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds 2 config options which enables hci_raw to work in
H:4 mode and enable it by default automatically.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When legacy advertising enable command is issues,
the BT_ADV_ADVERTISING has to be set, because this
flag is checked in many scenarios to see if the
advertising is ongoing or not.
Signed-off-by: Ahmed Shokry <ahmed.shokry@synopsys.com>
When disconnecting att_reset is called and all requests are notified
but instead of passing req->user_data like it should it pass the req
itself which nowdays comes from a k_mem_slab, rather than being a
contiguous memory that would contain the request and its user data,
which would likely cause invalid access.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch introduces two major changes to the directed advertising
feature of the bluetooth host.
Deprecating the bt_conn_create_slave_le, and removing
bt_conn_le_create_slave which has never been released. This behaviour
has now been moved by to providing the peer direct address into the
advertising parameters.
Introducing directed advertising support for nonconnectable
directed extended advertising, both scannable and non-scannable.
A bug was also fixed in the the directed-adv command in the shell
when the argument "low" was given. The advertiseng parameter pointer
declared with BT_LE_ADV_CONN_DIR_LOW_DUTY was declared in a scope that
was no longer valid when it was used to start the advertiser.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Check the return value of LE Set Extended Advertising Parameters
command when starting an advertiser from bt_le_adv_start with
CONFIG_BT_EXT_ADV enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The LE Set Extended Advertising Set Random Address command may be
issued at any time after an advertising set identified by
the Advertising Handle parameter has been created using the
LE Set Extended Advertising Parameters command.
This commit fixes the advertising set issueing the set random address
command before the advertising set is created in the controller.
Since the le_adv_set_random_addr function has is used to get the the
own address parameter for the it could not simply be moved, and
moving the own address parameter handling out of this function
would create a potentioal maintaince problem.
Also this function is used for both with and without advertising
extension feature so changing it is not trivial without breaking all
the previous random address handling already put in place.
The simplest solution was therefore to postpone the command until the
parameters has been set using 2 flags.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use bluetooth assert on HCI command send error since this assertion is
always enabled and we should not continue after this has failed.
Log command status failure with information in order to make it more
visible as the HCI status code is more interesting than the -EIO error
code returned by the function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix the pending slave set connection latency and timeout values not used
in the connection update procedure when
CONFIG_BT_GAP_PERIPHERAL_PREF_PARAMS has not been enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Extends the bt_conn_le_create_param struct to provide the option
to set a custom timeout for the initiation of the connection.
The logic for the default values of window_coded and interval_coded
were moved to conn.c in order to resolve all defaults for the
create_param struct at a single location.
Timeout is not added as a parameter to the BT_CONN_LE_CREATE_PARAM
macro due to the expectation that CONFIG_BT_CREATE_CONN_TIMEOUT
will be the typical value that users will expect.
Fixes#23468
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Fix an an issue where established bonding information in the peripheral
are deleted when the central does not have the bond information.
This could be because the central has removed the bond information, or
this is in fact not the central but someone spoofing it's identity, or
an accidental RPA match.
This is a regression from: a3e89e84a8
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add additional build configurations to the shell to catch build errors
when enabling extended advertising.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix compilation issue when extended advertising is enabled but privacy
is disabled. In this case the rpa_update work is compiled out.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Most places used an int so that should have handled most cases but
keys_set was using an unsigned int, which meant that checking len > 0
is an expression that is always false, and the error handling is not
working.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix high-duty cycle directed advertising when extended advertising
feature has been enabled. The duration parameter when starting extended
high duty cycle directed advertising has to be set to a non-zero value
less than or equal to 1.28 seconds.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Avoid removing identity keys from the controller during the pairing
procedure. During the pairing procedure the keys will be cleared before
they are updated. This causes an unnecessary warning from HCI core where
it tries to remove an IRK key-set from the controller that has has not
been added yet.
While this is not an issue, the warning from HCI core is misleading and
might lead to unnecessary questions and investigations.
Warning appeared after: 6c6bd8c49e
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the pending ID keys add and delete flag out of keys storage area.
These flags are runtime flags and should not be stored in persistent
storage.
Due to struct alignment storage start has to be aligned so that
variables added before storage start does not affect the storage bytes
by introducing padding in the storage area
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Skip feature testing of controller features when legacy advertising
commands are not supported. For combined builds or builds where the
capability of the controller is known it is not required to have runtime
check of controller extended advertising support.
This gives the following size reduction for hci_core.c:
Without legacy support
hci_core.c 19980 7.75%
total 257679
With legacy support
hci_core.c 21816 8.41%
total 259519
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Handle updating the identity keys in the controller while a scanner
limited by timeout or advertiser limited by number of events or timeout
is active in the controller. For this case we mark they keys as pending
and handle the update of the resolving list ones the roles are stopped.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add RPA handling for scan limited by timeout. The scan limited by
timeout has no information about elapsed time when stopped. So pausing
the scan at RPA timeout has no new scan timeout value to set.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add error code to API for starting directed advertiser. Also rename the
API in order to follow the established naming pattern.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support for creating and advertising with an advertising set.
This has support to advertise with extended data and with long range
feature on Coded PHY.
Limited to only supported one advertising set.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support to use the extended conn create options to establish
connections on LE Coded PHY or 2M. This uses the connection options
set by bt_conn_set_scan_params.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add API to set the scan parameters used in the LE Create Connection
HCI command used by bt_conn_create_le and bt_conn_create_aute_le.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support for the new scan options and use the LE Extended Scan
HCI commands if they are available in the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Refactor scan and initiator random address handling to a helper function
so that it can be re-used.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add reference count old to new value transition in the debug print, this
makes it easier to interpret the printed line when debuggin reference
count bugs.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Extract setting advertising filter policy parameter from the adv params
options field to a helper function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update buffer sizes needed when advertising extensions is enabled. Since
BT_RX_BUF_LEN is used for the HCI command as well we need to fit the
full 255 bytes of the Set Extended Advertising Data or Scan Response
Data plus the 3 byte header of an HCI command.
For the discardable buffer size we need to fit the LE Extended
Advertising Report event, which can be a maximum of 255 bytes plus the
2 byte header of an HCI event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Deprecate BT_LE_ADV defines in hci.h that are expected to be used by the
application in the scan received callback to identify the advertising
PDU type. These defines are mixing HCI input parameters and advertising
PDU types. Internally it is acceptable to mix these, but at the API we
should to mix in them.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename filter_dup parameters used for scanning filter options to the
more generic name options, and make scan filter options follow same
naming patters as advertising and initiator scan options.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Deprecate bt_create_conn_le and rename it to in order to add return
code, new arguments and to follow the established naming convention.
Add API for the application to control the scan parameters of the
initiator role. This allows the application more scheduling control
of the initiator in multi-role scenarios. Also provides options to
configure the initiator for LE Coded PHY for long range support.
We deprecate the old way of creating connection to make the name more
consistent with the rest of the API.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix directed advertising from privacy disabled peer. In this case we
need to have the local IRK in the controllers resolving list in order to
have the controller resolve the initiator address of the directed
advertising pdu (ADV_DIR_IND).
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix directed advertiser using the wrong local IRK when doing directed
advertising when the identity of the advertiser is not the default
identity.
This is only an issue for the directed advertiser because it is only
for the directed advertiser that we use the controllers local IRK
to generate the Advertisers RPA.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add header definition for bt_read_static_addr function. Declaring it
without a header definition will not give any compilation error when
function definition changes.
Refactor nRF SoC specific code into nRF specific source files and
provide weak definitions when these are not implemented. This will make
it easier to add handlers per vendor.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When using BT_LE_ADV_NCONN_NAME then the advertising name will not be
included in the advertising data. This is because the host always puts
the device name in the scan response. But since the scan data was
otherwise empty the advertising type was set to ADV_NONCONN_IND.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fixes#23485
When we create a GATT table dynamically, we also create a hash
identifying this table. This hash can be stored in persistent memory and
we can thus determine after recreating the GATT table whether the
services have changed or not from before the reboot.
When these hashes are identical, it implies that the table has not
changed, wherefore a service changed indication should not be sent to
any bonded clients. The method for achieving this was to remove the
gatt_sc.work entry from the work queue. This work queue entry was to
send an indication to the clients when the table had been allocated.
If the final entry then caused the hashes to match, the indication
would be cancelled.
On unit testing this behaviour in simulation and in practice, we found
that the indication was sent nonetheless, and the issue was located to
be tied to the SERVICE_RANGE_CHANGED flag which is set when the services
are changed and is cleared when the indications are being sent out.
It was the job of the work queue entry to clear this flag, and as the
entry was never serviced, the flag was never cleared, and when
sc_commit() is called at the end of the process, it believes that there
is a new service change pending and therefore starts the job over, thus
creating a redundant indication to the clients.
This commit fixes the issue by clearing the flag when the work entry
is removed due to a hash match. This has been unittested in a live
environment, in a simulation environment, and sanitycheck has been run
on it.
Signed-off-by: Dan Erichsen <daee@demant.com>
The commit e85dd8af5d changed the way the BT_ECC Kconfig option
is enabled, however it got the dependency wrong. The dependency should
only look at BT_SMP_OOB_LEGACY_PAIR_ONLY if BT_SMP was also enable.
This broke e.g. the build of the mesh_demo app for the BBC
micro:bit since the memory consumption jumped up by roughly 2k.
This patch fixes the issue, and in the same go makes the Mesh handling
consistent by also using a conditional default rather than select.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Allow to get local OOB data while advertiser, scanner or whitelist
initiator is active. If direct initiator is active or the advertiser
is using the random address as a random static identity address then
the function will return error.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When OOB callbacks are present it is possible to achieve authenticated
pairing without having the remote OOB data present. Using OOB with
LE Secure Connection only one side of the pairing procedure is required
to have the OOB data present. If we have given the remote our OOB data
then pairing can proceed.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Added CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY option that completely disables
all legacy and SC pairing modes(except for Out of Band) and frees the
memory previously used by these.
Added CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY option that force rejects
pair requests that lead to legacy Just Works or Passkey pairing.
Signed-off-by: Iván Morales <ivan98ams@gmail.com>
Refactor old state handling in bt_conn_set_state to use switch statement
instead of if statements.
This will give us warning about enum values not covered.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix connection complete event handling when the local RPA is not valid.
This can happen when the controller was not instructed to use an RPA
address, or the local IRK was set to an all zero IRK.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
According to the Zephyr VS HCI specification:
Only Read_Version_Information and Read_Supported_Commands commands are
mandatory.
Check for supported Read Supported Features command before issuing this
command to the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix host resolving the peer identity address in enhanced connection
complete event when the resolving list in the controller is full and
resolution is done in the host.
Move the handling from legacy connection complete into enhanced
connection complete event so that it is done for both connection
complete events.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
If the application has used bt_le_oob_get_local to retrieve the OOB
RPA address and OOB authentication information the central role should
use this RPA address for the next RPA timeout period.
The central role always refreshes the RPA address for the initiator,
this will make the OOB information not usable as the peer cannot
recognize the central role since the RPA address is changed.
Check if the initiator can use the address for the duration of the of
remaining RPA period.
Fix central role using the advertiser identity when setting the private
address. The central role should only use the default identity.
Regressions from:
fbe3285bfa
and
4876a8f39a
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
If the client is change-unware and disconnects the spec requires that
the stack still sends the error out of sync for the next request:
'The ATT_ERROR_RSP PDU is sent only once after the client becomes
change-unaware, unless the client _disconnects_ or the database changes
again before the client becomes change-aware in which case the
ATT_ERROR_RSP PDU shall be sent again'
Fixes#23110
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix issue where a new connection with the same peer would use the CCC
from from first connection, despite different local identity.
Since there is no CCC for the new connection yet this caused the
application to think that CCC was enabled but the remote device had not
yet subscribed.
Fix this issue by making the id as an input to the peer address check
function. This will force us to make the check every time. This commit
might also fix similar issues not yes discovered as the ID check was
missing in a few other places as well.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename the acl buf context id to index since to avoid confusing it with
the conn object ID parameter. Especially the bt_conn_lookup_id function
was creating confusion.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Avoid the HCI-USB race condition where HCI data and HCI events can be
re-ordered, and pairing information appears to be sent unencrypted.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix issue where an invalid (all zeroes) hash was written to settings
storage on reset. This caused the old value to written to zeroes, before
being written back to it's original value again immediately after.
This causes excessive flash wear.
This happens because the check if (k_delayed_work_remaining) returns the
amount of time until the work will execute. When that time has run out
the time is zero, but the work has not yet been executed.
We then write the invalid hash to flash, and then once the work-item
executes it will write the correct value.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
SC config data is no longer stored within the CCC config itself
therefore it must be cleared separately.
Fixes#22539
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GATT data shall not be considered conditional to BT_SETTINGS since
the data is stored in RAM it must also be cleared when unpairing.
Fixes#22514
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
smp_pairing_complete does actually clears flags so setting
SMP_FLAG_TIMEOUT must come after that.
Fixes#22786
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix bt_gatt_indicate using the wrong attribute pointer when a uuid was
provided as input.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename the scan recv callback info struct so that it reflects that it
is part of the scan recv callback. This will make it consistent with
future plans for advertising callbacks.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix the scanner using the advertiser identity instead of the scanners
identity, scanner always use BT_ID_DEFAULT.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Corrected configuration of BT_HCI_RESERVE for the RPMsg HCI driver.
This change fixes the following assert:
[net_buf_simple_headroom(buf) >= len] @ ZEPHYR_BASE/subsys/net/buf.c:881
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This can happens if for example the remote peer have the initial credits
set to 0 which would cause bt_l2cap_chan_send to fail instead of just
queue the packets until more credits are given.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The existing stack_analyze APIs had some problems:
1. Not properly namespaced
2. Accepted the stack object as a parameter, yet the stack object
does not contain the necessary information to get the associated
buffer region, the thread object is needed for this
3. Caused a crash on certain platforms that do not allow inspection
of unused stack space for the currently running thread
4. No user mode access
5. Separately passed in thread name
We deprecate these functions and add a new API
k_thread_stack_space_get() which addresses all of these issues.
A helper API log_stack_usage() also added which resembles
STACK_ANALYZE() in functionality.
Fixes: #17852
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This commit adds a new option CONFIG_BT_SMP_USB_HCI_CTLR_WORKAROUND
to support USB HCI controllers that sometimes send out-of-order HCI
events and ACL Data due to using different USB endpoints.
Enabling this option will make the master role not require the
encryption-change event to be received before accepting
key-distribution data.
It opens up for a potential vulnerability as the master cannot detect
if the keys are distributed over an encrypted link.
Fixes: #22086
Signed-off-by: François Delawarde <fnde@oticon.com>
Directed advertising timeout was dropped in the host due to
not being able to find a pending connection. Host used the
role parameter from the error event parameters which has
been earlier zero-ed out.
Regression introduced in commit a0349689ff ("Bluetooth:
host: Fix conn object assigned to wrong connection")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When starting a non-connectable advertiser and an active scanner is also
using NRPA address then this use-case should be supported. A new
advertiser that is non-connectable should have a fresh NRPA address
every time it is started, so we must refresh the NRPA used by the active
scanner.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When advertiser is disabled we should update the random address for both
passive and active scanner back to an NRPA. But this command will fail
because the if the scanner is an active scanner, we must disable and
re-enabled the active scanner after setting the random address.
This behavior should not be there when scanner is configured to scan
with identity address.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Document why a privacy-disabled scanner will not notify about directed
advertising reports. This is the default behaviour of the
privacy-disabled scanner. In order to receive the reports the option
BT_SCAN_WITH_IDENTITY must be enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Prevent the advertiser from overwriting the passive scanners identity
address when the scanner has been configured to scan using the identity.
In this case the LE Set Random Address command would not prevent the
address from being overwritten. So instead we explicitly stop it in the
host.
Also fix original code function not working at all since the first
if statement was should had a bad check. Resulting in it always
returning success.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Drop directed advertiser reports when the passive scanner should have
been using the NRPA address. The advertiser has overwritten the NRPA
with it's identity address instead and a peer is sending directed
advertiser packets to it.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When privacy is disabled by default the scanner still protects it's
identity with the use of NRPA addresses. We should not set the identity
address for the passive scanner unless the Kconfig option to scan with
the identity has been enabled.
This makes passive scanner behave the same way as an active scanner
since none of them will report directed advertising reports towards
the scanners identity.
This also enables the advertiser to switch out the random address which
is needed for the Bluetooth Mesh LPN case.
Fixes#22088.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Similar to pairing_confirm this callback is called each
time a peer requests pairing, but for all types of
pairings, except SSP. The pairing req/rsp information is
passed as a parameter so the application can decide
wheter to accept or reject the pairing.
Fixes: #21036
Signed-off-by: Martin Rieva <mrrv@demant.com>
Fix infinite recursion in host-based bt_rand function. This would call
HCI LE Random Number command, which would in turn call bt_rand, causing
an infinite recursion.
bt_rand -> prng_reseed -> BT_HCI_OP_LE_RAND -> le_rand -> bt_rand
To solve this issue the controller should avoid doing calls into the
host, so all calls to bt_rand in the controller should be replaced with
a call to a controller function.
Fixes#22202
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix LE Create Connection command giving out of range parameters to the
controller, this came back as 0x30 (Out of Range Parameters) status code
on the command from the controller.
This appears to be the min and max CE parameters in the command.
Revert back memset from 137f704064
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix problem where application was notified about a new connection being
established, but no connection has actually been made.
This occurred because the LE Create Connection command failed directly
from the API, in which case the state transition thinks the err is valid
and always notifies the application.
Introduced by:
6c1f52dff7 for bt_conn_create_le
e9eebf0c40 for bt_conn_create_auto_le.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix an issue where a slot in the key pool was considered free when
either the address was cleared or no keys were written in the entry
(enc_size == 0). This caused a problem with simultaneous pairing
attempts that would be assigned the same entry.
This patch makes it so a a slot is considered free even when keys are
not yet present in the entry, and makes sure the address is cleared in
case of pairing failure or timeout so to mark the slot as free.
Signed-off-by: François Delawarde <fnde@oticon.com>
Moves the Mesh AES-CCM module out into a separate module, to make it
accessible from other subsystems. Adds the new CCM API in
include/bluetooth/crypto.h along with the bt_encrypt functions.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Move reset of channel status from after the destroy callback since the
after the destroy callback the memory should be assumed to be released.
Instead clear the channel status when the channel is created in
l2cap_chan_add. This way we don't rely on the memory given being set to
the correct value.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix ATT releasing the att structure back to the memory slab allocator
before the structure is actually ready to be released. The memory slab
allocator will write context data inside the freed slab which is
currently being overwritten by l2cap during channel teardown.
This manifests as an "Unable to allocate ATT context for conn" when
reconnecting with multiple connections.
Since the l2cap channel is embedded inside of the ATT context and l2cap
still has a valid referenc to the l2cap channel we need to release the
ATT context at a later time.
This should be fixed by implementing the channel destroy function and
releasing the channel there.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add the option to provide the destroy callback to the fixed channels.
This can be used to free the memory for the L2CAP channel context which
is provided by the fixed channel in the accept callback.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The callback function may modify the att->req and it has to be
called after the att_process. The att_process does not re-check
if att->req is still NULL.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
