exti driver implementation does not fit all SoCs because
some EXTI ip does not match stm32_exti register map provided.
Instead of providing exti register map for all SoCs, use LL API
which abstracts IP variations and enable uniform use of the drivers
on all STM32SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Clean up a left over from GPIO driver factorization.
Definition of GPIO_REG_SIZE and GPIO_PORTS_BASE do not need anymore
to be spread accross SoCs.
Put these definitions directly in STM32 pinmux driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The original implementation of gpio functions access registers
directly. Using LL library can add a set of unifying access
functions for all series of stm32 for avoiding accessing low level
code, and improve readability.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
All series STM32 have mostly the same GPIO architecture
and can share the same code for GPIO manipulation.
Functions of the external interrupt line control are also the same.
This patch extracts common code from them and put them into the 'common'
folder.
Functions of control GPIO of these series scattered in
soc/arm/st_stm32/stm32xx/ folders contain these functions:
stm32_gpio_flags_to_conf(), stm32_gpio_configure(), stm32_gpio_set(),
stm32_gpio_get, stm32_gpio_enable_int().
This patch merges them into the gpio_stm32.c file.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Provide CONFIG macros for clocks bits and bus properties in fixup
files and use them to simplify logic in uart devices instanciation
code
Fixes#10448
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The information extracted from the device tree is now used to initialize
GPIO device instances. Up until now the GPIO device driver made no use
of this information. Actual instance creation is still controlled using
the Kconfig method. Missing GPIO device tree nodes were added in the
process for STM32L073, STM32F413 and STM32F373.
The information for gpio instance initialization has already been
present for supported STM32 SoCs but remained unused. Changes in the
device tree had no effect on GPIO functionality and was essentially
redundant. Using the device tree for hardware description seems
plausible and less painful than a myriad of defines in some SoC
description header.
The change was implemented under the assumption that current device
trees provide a correct description of the SoCs. Base register addresses
and RCC register bits were not explicitly checked for each device.
Manual tests were executed on:
- NUCLEO-F103RB
- STM32F429I-DISCO
- STM32F746G-DISCO
- NUCLEO-F767ZI
Manual tests consisted of blinky on different GPIOs and pins on each
board.
sanitycheck was executed for all STM32 based boards
Fixes: #10629
Signed-off-by: Martin Bertsche <martin72216@googlemail.com>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
