This provides a better error message when building with CMake and
forgetting ZEPHYR_BASE or not registering Zephyr in the CMake package
registry. See parent commit for more details (split from parent for
better readability).
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Integrated temperature sensor sample fetch and use of the value
in the GATT indications.
Signed-off-by: Charan Pudiyaneravana Venkatesh <charan.pv@sixoctets.com>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Switch to using the synchronous bt_init call before starting the main
loop in the peripheral samples. This is to avoid sending notifications
before bluetooth has been properly initialized.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add the required specific HW configuration for SW defined
BLE LL on RV32M1 SoC, by means of DTS overlays:
- enable INTMUX0 channels 2 & 3
- route Generic FSK RF0 interrupt to INTMUX channel 3
- route LPTMR1 interrupt to INTMUX channel 2
This change is done for all Bluetooth samples that are intended to
run on RV32M1 using BLE SW LL.
Signed-off-by: George Stefan <george.stefan@nxp.com>
Signed-off-by: Radu Alexe <radu.alexe@nxp.com>
Signed-off-by: Ionut Ursescu <ionut.ursescu@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
This adds support to set different permissions to CCCD so security can
be checked when enabling notification which conforms to:
BLUETOOTH CORE SPECIFICATION Version 5.1 | Vol 3, Part G page 2360:
'3.3.3.3 Client Characteristic Configuration
Authentication and authorization may be required by the server to
write the configuration descriptor.'
In addition to that also ensure that notification are not re-enabled
until the proper security level is reached to conform to the following
statement:
'10.3.1.1 Handling of GATT indications and notifications
A client “requests” a server to send indications and notifications
by appropriately configuring the server via a Client Characteristic
Configuration Descriptor. Since the configuration is persistent
across a disconnection and reconnection, security requirements must
be checked against the configuration upon a reconnection before
sending indications or notifications. When a server reconnects to a
client to send an indication or notification for which security is
required, the server shall initiate or request encryption with the
client prior to sending an indication or notification. If the client
does not have an LTK indicating that the client has lost the bond,
enabling encryption will fail.'
Fixes#17983
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the necessity of registering the storage for CCC and make
it part of the declaration itself.
Fixes#18547
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Error codes are listed in header files and in the core spec as hex
values. Always print them in hex in debug for easier error code
checking.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the health thermometer service into the sample folder that
demonstrates it. This avoids long build paths
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This commit moves the BLE GATT Battery service
from /samples/bluetooth/gatt to /subsys/bluetooth/services and
adds a Kconfig entry to enable and configure the service;
when enabled, it will register itself automatically.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Adding Health Thermometer Service sample. Refer to Health Thermometer
Profile Specification for detailed information about the Health
Thermometer Profile.
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
