Removes redundant and invalid configurations from the bluetooth/mesh
sample. Removes some stale disabled config entries.
Fixes L2CAP related warning in config step of sample.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Adds the model extension concept to the access layer, as described in
the Mesh Profile Specification, Section 2.3.6. Extensions are
implemented as a tree, using two pointers in each model:
The extends pointer points to the first extended model, and the next
pointer points to the next sibling or (if the NEXT_IS_PARENT flag is
set) the parent model in the tree, forming a cyclical "Left-child
right-sibling" (LCRS) tree. The tree root can be obtained by calling
bt_mesh_model_root_get(), and the extended models can be walked by
calling bt_mesh_model_tree_walk().
According to the Mesh Profile Specification Section 4.2.3, all models in
the same extension tree share one subscription list per element. This is
implemented by walking the model's extension tree, and pooling the
subscription lists of all models in the same element into one. If the
config server adds a subscription to a model, it may be stored in any of
the model tree's models' subscription lists. No two models in the same
extension tree and element will have duplicate groups listed. This
allows us to increase extended models' capacity for subscriptions
significantly.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Removes the special stack config setting in the Bluetooth Mesh sample to
allow it to run with other Bluetooth controllers.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Introduce a separate buffer pool for events which the HCI driver
considers discardable. Examples of such events could be e.g.
Advertising Reports. The benefit of having such a pool means that the
if there is a heavy inflow of such events it will not cause the
allocation for other critical events to block and may even eliminate
deadlocks in some cases.
Also update all mesh samples not to specify explicit RX buffer counts
anymore. Instead, create appropriate defaults in Kconfig so that we
only need to override this in the app for cases like the bbc:microbit
with limited memory.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This sample is often the first one used as reference for Bluetooth
Mesh, so it should have a good configuration as a starting point.
Comment out the LPN options to eliminate Kconfig warnings, since the
LOW_POWER option they depend on is not enabled. Also disable
INIT_STACKS since that's only needed for fine-tuning the app
configuration, and otherwise only causes unnecessary spam in the
console.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds common option to disable support for LE Data Length Update
procedure in controller and host.
This will reduce flash usage by compiling out le_data_len_change
event handler that will never be called if controller has been
compiled with BT_CTLR_DATA_LENGTH option disabled.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This adds common option to disable support for PHY Update
procedure in controller and host.
This will reduce flash usage by compiling out le_phy_update_complete
event handler that will never be called if controller has been
compiled with BT_CTLR_PHY option disabled.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
The number of buffres influences e.g. the maximum SDU size, which in
turn influences call stack consumption. Use lower values where a high
number of buffers isn't necessary, and use the default (6) where it's
sufficient.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of having an RPL-specific storage timer, introduce a generic
one that'll eventually be used for all persistent storage.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add initial skeleton for doing settings-based persistent storage for
the mesh network state. This patch only includes restoring some core
network state such as IV Index, Sequence number, Net Keys, App Keys
and the Replay Protection list. The remaining state, and actually
storing the state, is left for follow-up patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This makes it possible to pass all IV Update tests without having to
build a custom configuration for some of the tests. We also disable
the feature in all sample configurations, but leave it on in the
tests.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
From section 3.4.5.3 in the Mesh Profile Specification 1.0:
"A node shall implement a Local Network Interface."
Removing the Kconfig option also helps clean up quite a lot of code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Count of 4 seems to cause deadlocks with some Android phones due to
other GATT activity in addition to Mesh related data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There's no need for debug logs by default in the mesh sample, and it
just contributes excessively to the ROM footprint.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add an initial implementation for the Bluetooth Mesh Profile
Specification. The main code resides in subsys/bluetooth/host/mesh and
the public API can be found in include/bluetooth/mesh.h. There are a
couple of samples provided as well under samples/bluetooth and
tests/bluetooth.
The implementation covers all layers of the Bluetooth Mesh stack and
most optional features as well. The following is a list of some of
these features and the c-files where the implementation can be found:
- GATT & Advertising bearers (proxy.c & adv.c)
- Network Layer (net.c)
- Lower and Upper Transport Layers (transport.c)
- Access Layer (access.c)
- Foundation Models, Server role (health.c & cfg.c)
- Both PB-ADV and PB-GATT based provisioning (prov.c)
- Low Power Node support (lpn.c)
- Relay support (net.c)
- GATT Proxy (proxy.c)
Notable features that are *not* part of the implementation:
- Friend support (initial bits are in place in friend.c)
- Provisioner support (low-value for typical Zephyr devices)
- GATT Client (low-value for typical Zephyr devices)
Jira: ZEP-2360
Change-Id: Ic773113dbfd84878ff8cee7fe2bb948f0ace19ed
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
