This reverts commit 698de88916 ("Bluetooth: controller:
Cleanup redundant ticker busy loop")
Scan enable asserted in ctrl.c line 3756 due to the fact that a
role event was active and ticker job has hence been disabled.
Add back the busy loop so that scan enable can wait until the
active role event completes gracefully.
The ticker busy loop is mandatory in all ticker interface calls
if a blocking behavior is desired.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The calculation in packet_rx_reserve_get() was already handled by
packet_rx_acquired_count_get(). So, let's use that code instead
and remove the duplication.
Change-Id: Ic76f70f1e78bebc74f5bef36cd92a3c332e489e9
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This calculation can be used in packet_rx_reserve_get() where currently
the code is duplicated from packet_rx_acquired_count_get().
Let's allow use of packet_rx_acquired_count_get() regardless of whether
CONFIG_BLUETOOTH_CONTROLLER_DATA_LENGTH is enabled.
Change-Id: I613bde0a407f3caccabb22f369098575965e98ad
Signed-off-by: Michael Scott <michael.scott@linaro.org>
During testing, lr->max_rx_octets and lr->max_tx_octets were
at times set to 0. If we use these 0 values, we end up with
very erratic behavior. Best, to check for a sane value and
if invalid, default to the value in _radio.conn_curr->max_*x_octets.
Change-Id: I57c0e3790d988f0de17993cebe5c5c2ab0fc07a6
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When Controller to Host flow control is enabled, output informational
messages for certain operations to help tune and debug the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the HCI driver debug option applies to both files in
drivers/bluetooth and subsys/bluetooth, the configuration option itself
now lives in the top-level Kconfig file for consistency.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added implementation to auto-update Bluetooth PHY to 2Mbps
if the local Controller supports it.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added support for Bluetooth v5.0 PHY Update Procedure in the
Controller.
Asymmetric PHY connections do not work for now due to the
Radio mode not being setup in time in the ISR during tIFS
period and the Radio already ramping up in the cached
previous Radio mode to meet tIFS deadline.
Subsequent commits will add this feature, by either double
buffering the mode in software or using fast radio ramp up
which gives enough time in the ISR to change the mode.
Jira: ZEP-2086
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Scale the ctrl pkt enqueue implementation to allow multiple
ctrl packets to be enqueued. This will aid in the graceful
implementation of parallel control procedure collisions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added HCI macros to check LE Features. Also, added test
macros for 2M and Coded PHY support in HCI Controller.
Earlier a common test macro was used between BR/EDR and LE,
but since LE features do not use pages for feature, an
explicit macro for testing LE feature is added now.
Also, features field in LE device structure is now a single
dimension array of 8 octets.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The APIs for allocating RX buffers were modified recently and hci_raw
had not reflected those changes properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When we send TCP data segment, we need to set the length
of the application data by calling net_pkt_set_appdatalen().
This is done so that sequence number can be properly
advanced when we receive ACK to that pending packet.
Signed-off-by: xiaorui hu <xiaorui.hu@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The event mask population used to let the Controller know which events
are relevant to the Host needs to take into account the features
supported by the Controller itself, in order to only enable those that
are indeed valid.
Jira: ZEP-2050
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the framework for LE Scan Request Received Event.
The feature is available under the Controller's advanced
features and will be selected implcitly when Bluetooth v5.0
LE Advertising Extensions feature is implemented.
Jira: ZEP-2073
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove unreferenced function hci_evt_is_discardable after
introduction of hci_get_class function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In preparation for refactoring the Controller implementation
into seperate state and role based source files, add Kconfig
options for states and roles in the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To guarantee code that is endianness-independent, the sys_le* macros
must be used everywhere when accessing multi-byte values from the
command parameters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In HCI, the response buffer to a command is the same as the one for the
command itself, requiring command parameters to be processed before the
response is formed on the same memory area.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since Controller to Host flow control is a feature that affects both
sides equally, move it to the top-level Kconfig file and consolidate its
use in both Controller and Host.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This feature was removed some time ago, but turns out it's important
to have it available for split host-controller setups.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Enable the bits corresponding to the new 3 commands supported when
enabling Controller to Host Flow Control, in order for the Host to be
able to enable the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to achieve proper sharing of configuration options, everything
that is common to both the Host and the Controller should now be placed
in the top-level Kconfig file, and Controller-only options are in the
controller/ Kconfig one.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Introduce alternative TRX switching using dedicated timers
and peripheral interconnect. This will enable the
possibility to independently configure the Tx and Rx
settings between the tIFS.
Note, this will also provide the opportunity to design a
soft realtime Radio ISR.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The Bluetooth Specification allows for optional Controller to Host flow
control based on the same credit-based mechanism as the Host to
Controller one. This is particularly useful in 2-chip solutions where
the Host and the Controller are connected via a physical link (UART, SPI
or similar) where the Host is sometimes required to ask the Controller
to throttle its data traffic while still making sure that relevant
events get through the line.
This implementation is based on a simple queue of pending events and
data that is populated whenever the Controller detects that the Host is
out of buffers and then emptied whenever the Host notifies the
Controller that is ready to receive data again. Events relevant to the
connections are also queued to preserve the order of arrival.
At this point the Controller ignores the connection handle sent by the
Host and treats all connections equally, and it also queues events even
for connections that have no data pending in the queue. Both this items
can be improved if necessity arises.
Note that Number of Completed Packets will still flow freely from the
Controller to the Host regardless of the pending ACL data packets, which
might lead to inconsistencies in the sequential order of certain
operations that include bi-directional data transfer.
Jira: ZEP-1735
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When adding link-local address to the cache the type needs to be
properly set as net_ipv6_addr_create_iid will attempt to use it
when generating the IPv6 address.
Jira: ZEP-2077
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is related to commit "net: tcp: Make sure ACK timer is not
run if cancelled" which did not set the cancel flag when the timer
was cancelled from tcp.c.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
And print a warning if that happens.
This will also avoid to raise an ASSERT on net_if_tx_thread()'s k_poll
as this one will be called with no events to work with.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This ensures that an unknown request won't cause ATT to timeout since
no response is currently generated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Rename ll_address_* to ll_addr_*. Also, update ll_addr_get
to return reference to stored public or random address.
Change-id: I22cb0135d2223f679c4d9321f4724f8b7de0aede
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Fix the attr->handler reference to attr->handle.
Change-Id: I4a6ccee7860abf800f51df404979eac18eb26e8e
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Rename occurences of bt_hci_ev_* to more widely used
bt_hci_evt_* namespace.
Change-id: I742fb86f8f835a0f6072638e1e997ad08891d43d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
In the Controller's radio hal, explicitly differentiate
between Advertisement and Data channel packet
configuration.
Also, remove nRF5x specific extra overhead in Advertisement
PDU structure.
Change-id: I942b88a160af78f8900d7e49fb5f36c8aa493b97
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
L2CAP Dynamic Channel feature uses the global connection Tx
pool for segmentation either when there is no free buffers
in the original application pool or when the original data
buffer has no headroom to add L2CAP headers.
This eliminates the need for a dedicated fallback pool for
Dynamic Channel segmentation.
Change-id: Ia5452c814169d17ef261ecef425a8fcf2e7e1e84
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This function already has an 'i' variable on the top-level, so no need
to declare a second one that'd just shadow the original.
Change-Id: I5dfa4df2c4793be220a40ac642b19bf440e80220
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The segment allocation function can't fail (it eventually waits with
K_FOREVER for a buffer to become available), so there's no point in
checking its return value for NULL. Also, the connection state check
is because of this particular waiting and not the semaphore waiting
(which is done with K_NO_WAIT).
Change-Id: I9698760541de810869cffc1c60cf97c5f8f7df8d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
L2CAP Tx segmentation used BT_L2CAP_RX_MTU value which is
the value used by fixed channel protocols. Decoupling the
buffer size provides the opportunity to reduce RAM used per
connection.
Change-id: Id064f9b2e3f02073402815d09c3ea13a35df2a6c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Remove BT_ prefix from BT_L2CAP_MAX_LE_MPS and
BT_L2CAP_MAX_LE_MTU as they are internal to l2cap.c file.
Change-id: I6abec0a1f07b8aef49940ab7abeaacbd19947e0b
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The switch from C99 integer types to u16_t, etc. caused misalignment
in structs and function definitions with multi-line parameter lists.
Change-Id: I1448b159ab1afe50ff88b7a6bd1b254c44858d4c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This information should be part of the main BR/EDR context struct,
rather than there being a separate member in struct bt_dev. If/when
the needed ESCO information grows we can consider having a separate
struct, but even then it should be part of the main BR/EDR struct
instead of sitting directly in bt_dev.
Change-Id: I3edf120606ea6c6974f515bba90de2b25fc6fac6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The switch from C99 integer types to u16_t, etc. caused misalignment
in structs and function definitions with multi-line parameter lists.
Change-Id: Ic0e33dc199f834ad7772417bca4c0b2d2f779d15
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
