Due to varying remainder value, first interval will need to
consider the remainder value used in microsecond timing from
the start of the initiator window.
Also the tx chain delay and ready delay must be substract
after the window offset is calculated.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The Read Remote Version Information command is supported on the BLE
controller, enable the bit in Read Local Supported Commands to reflect
this.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Setting just IPv4 address as was allowed before isn't enough for
real-world usage (e.g. accessing DNS and outside servers in general).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Per LwM2M spec (7.3.2.4 Operation on Object):
"If the payload (New Value) conveys an Object Instance ID in conflict
with one already present in the LwM2M Client, the complete request
MUST be rejected and a "Bad Request" error code MUST be sent back."
Let's do that.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Per LwM2M specification 7.3.2.4, "Optional Resources MAY be conveyed
in the "New Value" parameter as well; the LwM2M Client MAY ignore the
optional resources it doesn't support."
Update TLV/JSON writer to ignore error when object fields are not
found (treated as optional resource). This will allow the resources
supported being written.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: re-worked patch post addition of CREATE
operation.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Prior to this patch, a CREATE operation was handled as a WRITE operation
after the object instance was created. This becomes problematic when
handling of optional resources differs between these 2 operations.
Let's introduce an actual CREATE operation and use it later to create
these differences.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We are returning EINVAL from content format write ops when an object
field definition is not found (an optional field which is not
implemented). Instead, return ENOENT which lets the LwM2M engine
know to send ZOAP_RESPONSE_CODE_NOT_FOUND to the LwM2M server at the
end of handle_request().
NOTE: This behavior is not correct when we call the writer right after
a CREATE operation where the data is assigned to resources for the
first time. This case will be handled in a follow-up patch once we're
able to distinguish between a WRITE and a CREATE in the write op
handler.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
POSIX requires struct sockaddr's field to be named "sa_family"
(not just "family"):
http://pubs.opengroup.org/onlinepubs/009696699/basedefs/sys/socket.h.html
This change allows to port POSIX apps easier (including writing
portable apps using BSD Sockets compatible API).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Fix controller assert due to a bug introduced in commit
07270e52ba ("Bluetooth: controller: Coding style and
refactoring").
This reverts implementation to original way it was and the
calculation of the ticker expiry will now not overflow the
range of the RTC peripheral, which is a 24 bit counter.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_pkt_get_reserve_data ignores the timeout parameter when in isr,
using K_NO_WAIT instead, which can lead to invalid fragment.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Per LwM2M specification 5.3.1 Register, report "ct=11543" when JSON is
supported. Also, report the resource type as rt="oma.lwm2m" when "ct="
presents.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Per LwM2M specification 5.3.1 Register. When object instances are
available, object ID can be ignored in registration message
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
According to LwM2M specification 5.2.7.3 Bootstrap DISOCVER,
security object is only reported to the bootstrap server.
Correct the behavior to (1) report server object to the server
(2) do not report security object at registration time
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Fix checks for BT_HCI_RAW and move default range after the other range
options, required by Kconfig to avoid overwriting other options.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
This is how it's called in the main docs, so use this same phrase in
Kconfig and samples too.
Also, added some articles to docs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The RSSI value is an 8-bit signed integer. Since the Link Layer works
only with positive unsigned integers, translate into a negative number
at the HCI layer.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This option enables full debugging output for memory allocations.
As that can produce lot of output and slow down the device under test,
it is disabled by default.
The previous CONFIG_NET_DEBUG_NET_PKT will collect information about
memory allocations but will not print any output. Use "net mem" or
"net allocs" commands in net-shell to see the memory allocation status.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Because the name of the memory pool can be quite long, print
it last so that the columns get aligned nicely.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are not in ESTABLISHED state, then there is no need to
try to resend any pending data packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the expire send timer expires, then it sends the packet.
If that happens, then we must not try to send the same packet
again if we receive ACK etc. which can cause re-sends to happen.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the packet sending is slow then we must NOT increment the ref
count when re-sending it. This is unlikely but can happen if there
are lot of debug prints etc. extra activities that prevent the driver
to actually send the packet fast enough.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that the sent flag is only set after we have really
sent the packet and the driver has verified that.
If the net_pkt_set_sent() is called while still in tcp.c, then
depending on how fast the device is, it might happen that the
retry timer expires before the packet is actually sent. This was
seen in frdm-k64f with ethernet and various debug prints activated.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is a backlog entry when TCP context is released, then
cancel the ACK timer if one exists.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that a network packet is sent after calling
http_response_send_data(). Othwerwise the packets might be
piling up and not sent in timely manner.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some older C libraries do not have errno for EPFNOSUPPORT.
Fixes issues with newlib in some versions of Xtensa XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The initial function prototype did not have 'inline' in it,
resulting in a compiler warning with XCC.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It's never a good idea to redefine functions as macros if intended
to be unused in some configuration
- "statement with no effect" warnings
- "unused argument" warnings
- No type checking done if the macros are used
These have been redefined as empty inline functions.
Fixes compiler warnings with XCC.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The second 'const' is misguided, indicating that the returns pointer
value itself cannot be changed, but since pointers are passed by value
anyway this is not useful and was generating warnings with XCC.
The leading 'const' indicates that the memory pointed to is constant,
which is all we needed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Inline functions declared in header files need to be declared
static. Fixes a compiler warning with XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Older value of 256 was introduced in 1.7 times. Testing on
BOARD=96b_carbon with 2 weeks old codebase however showed that TX
thread stack however can grow to 324 bytes. Finally, with the
latest master, following stacks are reported on BLE disconnect
(with CONFIG_INIT_STACKS enabled):
rx stack (real size 1024): unused 452 usage 572 / 1024 (55 %)
tx stack (real size 384): unused 16 usage 368 / 384 (95 %)
Two outcomes:
1. TX stack needs increase.
2. Over time, the stack usage grows, plus variations in SPI
drivers should also be taken into account.
So, increase the stack size to 416 bytes, to leave some headroom
beyond the immediate values seen on 96b_carbon.
Jira: ZEP-2510
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Currently, the HTTP_NETWORK_TIMEOUT setting is hard-coded as 20 seconds.
Not every application may want to wait that long, so let's change this
to a CONFIG option: CONFIG_HTTP_CLIENT_NETWORK_TIMEOUT
NOTE: This also removes HTTP_NETWORK_TIMEOUT from the public http.h
include file. It was not being used externally to HTTP client sources.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Add a sample application that allows a Zephyr-based Bluetooth
controller to interface with an HCI driver via SPI. This sample
implements the same BT SPI protocol already as Zephyr's HCI SPI
driver.
Currently, the sample only supports the legacy SPI API.
Provide a single configuration file, avoiding board-specific
files. Some board-specific configuration information must be provided
via other means:
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_PIN
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Since Extended Scanner Filter Policies is an independent feature from
Controller-based Privacy, split it out so it can be built independently
and included without it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A TCP FIN message is passed on to user apps as a tcp_received_callback
with a NULL pkt parameter. This means the connection is closing and
the app should do whatever cleanup it needs as there will be no further
callbacks for the current TCP connection.
Currently, if a HTTP client request doesn't receive a "body" which
the HTTP parser can use to trigger on_message_complete, then the request
will end up timing out and most apps will think an error has occurred.
Instead, let's handle the TCP FIN message and return the waiting
semaphore, leaving the app to deal with whatever has been set in the
current HTTP context response data (IE: http_status).
This fixes using HTTP client to send POST data to servers which
only respond with HTTP_OK status and no body.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Unless offset was specified, it should default to 0, whereas
previously, value from the last command was used.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
"Network Application Support" itself is renamed from "Network
Applications" and also includes net_app API.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Whenever privacy is enabled, we support the Extended Scan Filter
Policies functionality, and therefore we must show it in the bitfield of
LE supported features for the controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Avoiding segmentation in the GATT-based Mesh Proxy protocol requires
having an RX buffer length of at least 77. We could round it up to 80
since there's otherwise wasted space, however there's also
BT_HCI_RESERVE to consider, so to avoid pushing over the 4-byte
boundary for certain HCI drivers just leave the size at 77.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is needed in order to get information which function is
doing the ref. With inline function this was not possible.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
