Assign special Product ID (0x101) to wpanusb protocol exporting
IEEE802.15.4 over USB.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This test prints out to the console, when testing on real hardware,
parse output and compare to what we are expecting to avoid timeouts.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove galileo as the only board to build for and cleanup the filtering.
Also, remove arduino 101 conf, this is not a networking platform we want
to tests.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Expand the contents of the smp_svr sample documentation so that it
covers all steps needed to perform DFU over BLE.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This application just enables VLAN tag for ethernet interface.
Set CONFIG_SAMPLE_VLAN_TAG option to define the desired VLAN tag.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of the sanitycheck tests were having too small limit for
network buffers when compiling for sam_e70_xplained board.
Increase the buffer limits when testing this for this board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some device include a temperature sensor, usually used as a
companion for helping in drift compensation, that measure the
die temperature. This temperature IS NOT related to the the
ambient temperature, hence a clean separation between the two
is required.
This commit introduces a clean separation between the two
types of temperature leaving the old deprecated definition
still there.
The list of current drivers that read the die (and not the ambient)
temperature is the following:
- adxl362
- bma280
- bmg160
- bmi160
- fxos8700
- lis3mdl
- lsm6ds0
- lsm6dsl
- lsm9ds0
- mpu6050
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add multifunction composite test for building USB device with HID and
MSC functions.
Fixes: #2613
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The current problem with HID is that we need to "patch" static
descriptor table with the size of report descriptor defined in the
user application.
The proposed solution is to have composite_pre_init() defined with
priority CONFIG_KERNEL_INIT_PRIORITY_DEVICE which should run before
composite_init() defined with priority
CONFIG_APPLICATION_INIT_PRIORITY.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
We can use default values of CONFIG_USB_DEVICE_VID and
CONFIG_USB_DEVICE_PID for sanity check builds.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The final ending chunk was not sent after the request was served.
This caused the remote client to constantly send the same request
to the server.
Fixes#6356
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In sample application of COAP put and post
methods are implemented in coap-server.c
and coap-client.c
Signed-off-by: Tarun Kumar Agarwal <tarun.kumar.agarwal@intel.com>
this sample expect there has a button in you board, that was
the mouse's left button, tested in linux by using evtest.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Combine several generic config file into prj.conf that can be
used by several boards and configurations.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This demostrates how to classify the network traffic when sending
data. The application will create similar functionality as
echo-client so user can use echo-server running in remote host to
test this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always allocating both IPv6 and IPv4 address information
to every network interface, allow more fine grained address
configuration. So it is possible to have IPv6 or IPv4 only network
interfaces.
This commit introduces two new config options:
CONFIG_NET_IF_MAX_IPV4_COUNT and CONFIG_NET_IF_MAX_IPV6_COUNT
which tell how many IP address information structs are allocated
statically. At runtime when network interface is setup, it is then
possible to attach this IP address info struct to a specific
network interface. This can save considerable amount of memory
as the IP address information struct can be quite large (depends
on how many IP addresses user configures in the system).
Note that the value of CONFIG_NET_IF_MAX_IPV4_COUNT and
CONFIG_NET_IF_MAX_IPV6_COUNT should reflect the estimated number of
network interfaces in the system. So if if CONFIG_NET_IF_MAX_IPV6_COUNT
is set to 1 and there are two network interfaces that need IPv6
addresses, then the system will not be able to setup IPv6 addresses to
the second network interface in this case. This scenario might be
just fine if the second network interface is IPv4 only. The net_if.c
will print a warning during startup if mismatch about the counts and
the actual number of network interface is detected.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move IP address settings from net_if to separate structs.
This is needed for VLAN support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add a sample that demonstrates a custom board definition. This proves
that BOARD_ROOT works and can be a useful reference when creating a
custom board definition.
Instead of spending time making up a board, the nrf52840_pca10056
board has been copied as-is. And the hello world sample has been used
as the basis for the application.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
There are currently two samples in the
~/zephyr/samples/application_development/ directory. This commit
allows them to be visible in the documentation.
It is not clear why this has not been done already.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Cover the required steps to use the Controller with Linux's BlueZ and
QEMU, and link to the relevant sections in the subsystem developer
guide.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to avoid duplication, move all information relating to QEMU and
BlueZ from samples to subsystems, and expand to cover BlueZ installation
and usage of Controllers with BlueZ and QEMU in detail.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the base64 encoding and decoding functionalit is now provided by a
separate library, remove the line in the CMakeLists.txt file that refers
to it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
With the new CONFIG_BOOTLOADER_MCUBOOT option there is no longer a need
to define custom overlays in order for a project to be bootable by
MCUboot. Remove therefore those unnecessary complications in the sample.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Each USB sample, when compiled, will provide a different
USB product string. A "nice to have" feature when trying
out the USB samples (they will show up differently in
`lsusb` or `dmesg`), and also illustrates how to set up
custom USB constants in the config files.
Requires #6589.
Signed-off-by: Iván Sánchez Ortega <ivan@sanchezortega.es>
With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
