We have cases with UART drivers where TX interrupt handling is not
bootstrapped properly on enabling them. To make such cases more
obvious, start this sample with console_write(), the output of which
wouldn't appear if that's the case. (Of course, the sample starts
with printk() exlaining what may happpen.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This commit would add the pull-up or pull-down on the switch pin and
makes it functional on the board where there is no external pull-up.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
If shell UART backend was enabled and logger uart backend was
not explicitly disabled then both were used resulting in logs
being printed twice on terminal.
Patch modifies default state of log uart backend to depend on
state of shell uart backend.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Changed LOG_MODULE_REGISTER and LOG_MODULE_DECLARE macros to take log
level as optional parameter. LOG_MODULE_DECLARE can now also be used
in static inline functions in headers. Added LOG_LEVEL_SET macro
which is used when instance logging API is used to indicate maximal
log level compiled into the file.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Couple of findings which were revealed after changing
LOG_MODULE_REGISTER macro:
- missing semicolons after LOG_MODULE_REGISTER()
- missing LOG_LEVEL defines
- other
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The USB mass storage documentation was completely outdated. Rewrite it
using reStructuredText, and mentioning the two possible overlays.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The HID mouse sample uses the GPIO to read the state of a button, but
does not enable CONFIG_GPIO, causing the example to fail. Fix that.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Stop specifying that the 'remote' app should use the same board as the
root app.
Also, add assertions to make sure that the user does not try to
override the board that is specified in the app build scripts.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Stop specifying that the OpenAMP 'remote' app should use the same
board as the root app.
Also, add assertions to make sure that the user does not try to
override the board's that are specified in the app build scripts.
This fixes#10345
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Provide basic commands for configuring/setting/reading GPIO ports.
> gpio conf ..
> gpio set ..
> gpio get ..
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add console harness support for USB mass storage test.
Also, using overlay config for DISK_ACCESS configuration
and accessing the different config file with different
method.
Signed-off-by: Ajay Kishore <ajay.kishore@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove redundant 'sample' tag and add something that matches the
functionality and features being tested, demonstrated.
Avoid short abbriviations and using full names for fs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If user will enable shell than for each backend shell instance
will be created automatically.
Update all shell examples according to the new initialization
procedure.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
The $srctree environment variable gives the path relative to which
'(o)source' statements work (the current directory is used if $srctree
is unset). It is set to $ZEPHYR_BASE in cmake/kconfig.cmake, so there's
no need to qualify the source of Kconfig.zephyr in sample Kconfig files
(or in external projects).
All 'source's in Zephyr assume that the Zephyr root directory is used as
the srctree as well, and would break otherwise.
Remove the $(ZEPHYR_BASE)s to make it clearer that all 'source'
statements work relative to the Zephyr root. There was some user
confusion on IRC.
Also explain how things work in the documentation.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
usb_dc_status_callback() parameters are interface or configuration
numbers and should be const.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Refactor USB writes, start transfer only when device
is configured, the change makes it possible to work with native_posix
USB virtual controller.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Some terminals literally interprets shell output data. Hence to print
a message in new line shell needs to send `\r\n` each time. To minimize
flash usage user can now send `\n` as a line delimiter and shell will
automatically add missing CR character.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
The way uart console is setup for this is not compatible with the logger
and needs additional changes, excluding until we have this implemented
in a generic way.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Added functionality to enable active shell backends via Kconfig
file. When there will be more backends implemented user will
have an option to select only required ones.
It is no longer needed to select SERIAL in prj.conf.
Fixes#10190
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Fixed a bug in the OpenAMP sample's recursive build scripts, where it
would pass on the wrong board to it's second CMake invocation.
This fixes#10345
Fixed the same bug in ipm_mcux.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
1. Shell will accept CR or LF as line delimiter.
2. Macro SHELL_DEFINE simplified - it no longer requires
new line character.
3. Fixes: #10207.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
1. Command handler can return command exectution status as int.
2. Existing command handlers rework.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Extending logger to support logging transient strings (with %s).
With dedicated call (log_strdup), string is duplicated to a buffer
from internal logger pool. Logger implicitly manages the pool.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The shell subsystem, as it is today, depends on having a UART,
therefore let's add the dependency explicitly in its Kconfig
Fixes#10190
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
It is no longer necessary to set the KCONFIG_ROOT variable when the
KConfig file is in the application root directory.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
