LPC GPIO architecture uses multiple devices.
GPIO input is routed via INPUTMUX to the PINT
device which roots the interrupt to NVIC.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Updates the mcux lpc driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle functions recently added to the gpio api.
ISR functions to be added later.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
stm32_exti_enable was returning errors on line > 32 or line pointing
to non implemented line. Both conditions are hard-coded, hence there
is no use to detect them dynamically in the code.
Check them with assert. As a consequence, function could now be void.
Additionally, enable exti irq line only if both checks are passed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since it is now possible to disable/re-enable interrupts and
also to reconfigure an already configured interrupt, it is
now required to clear non requested triggers.
While it is not strictly requested, triggers are also cleared
when interrupt is disabled (assuming trigger should be configured
when interrupt is enabled).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
fixup exti
Perform few clean up in stm32 gpio driver:
*Clean up uint32_t occurrences left over.
*Move function gpio_stm32_flags_to_conf from const to static
and remove useless parameter check
*Rework error handling in functoin gpio_stm32_config
*Remove gpio_stm32_int_enabled_port function and have direct call
to gpio_stm32_get_exti_source
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Updates the imx gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
- tests/drivers/gpio/gpio_basic_api
On boards:
- udoo_neo_full_m4
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Updates the mcux igpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Removes port configuration support since that feature is deprecated in
the new gpio api.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
On boards:
- mimxrt1015_evk
- mimxrt1020_evk
- mimxrt1050_evk
- mimxrt1060_evk
- mimxrt1064_evk
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Implement the new GPIO driver APIs for the HT16K33 and update the
driver to use the new GPIO flags.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
On the TI CC32xx, the GPIO peripheral supports only 8 pins per port.
We should add assertions where appropriate to verify this.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Updates the cc13x2/cc26x2 gpio driver and all associated boards to use
new device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Tested with:
samples/basic/blinky
samples/basic/button
tests/drivers/gpio/gpio_api_1pin
tests/drivers/gpio/gpio_basic_api
On board:
cc1352r1_launchxl
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Updates the cc32xx gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Tested with:
samples/basic/blinky
samples/basic/button
tests/drivers/gpio/gpio_api_1pin
tests/drivers/gpio/gpio_basic_api
On boards:
cc3220sf_launchxl
cc3235sf_launchxl
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API.
Tested on external SX1509B breakout board and Thingy:52.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
The interrupt triggering on both edges is a remnant from the old
Quark SE which has a customized DesignWare GPIO block. So remove
the support for both edges as the board is no longer supported.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The MCUX GPIO peripheral must be configured as either input or output.
Reject attempts to configure disconnected or bidirectional.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove handling for GPIO_INT_LEVELS_LOGICAL in driver now that we do
that in gpio_pin_interrupt_configure and gpio_pin_configure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove handling for GPIO_INT_LEVELS_LOGICAL in driver now that we do
that in gpio_pin_interrupt_configure and gpio_pin_configure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove handling for GPIO_INT_LEVELS_LOGICAL in driver now that we do
that in gpio_pin_interrupt_configure and gpio_pin_configure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove handling for GPIO_INT_LEVELS_LOGICAL in driver now that we do
that in gpio_pin_interrupt_configure and gpio_pin_configure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change when we clear interrupt status to happen before we handle the
callbacks. As the callbacks might manipluate the GPIO state and cause
a GPIO interrupt. If we clear interrupt status after than we might
miss an interrupt.
Also only clear interrupts for interrupts that are we have enabled and
that were reported when we read from the interrupt status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on frdm_k64f board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on nrf52840_pca10056 board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on sam_e70_xplained board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on efr32_slwstk6061a board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Both pin sets and values encoding pin values are ultimately represented
by 32-bit unsigned integers. Provide typedefs that make the role of a
parameter explicit.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit moves interrupt configuration for a single pin from
gpio_pin_configure to gpio_pin_interrupt_configure function.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds following functions which work with pin logical levels
(take into account GPIO_ACTIVE_LOW flag):
- gpio_port_get, gpio_port_set_masked, gpio_port_set_bits,
gpio_port_clear_bits, gpio_port_set_clr_bits
- gpio_pin_get, gpio_pin_set
Functions which work with pin physical levels:
- gpio_port_get_raw, gpio_port_set_masked_raw, gpio_port_set_bits_raw,
gpio_port_clear_bits_raw, gpio_port_set_clr_bits_raw
- gpio_pin_get_raw, gpio_pin_set_raw
As well as functions:
- gpio_port_toggle_bits, gpio_pin_toggle_bits
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
When building the i2s tests on 96b_argonkey we get the following
warnings:
drivers/dma/dma_stm32.c: In function 'dma_stm32_configure':
drivers/dma/dma_stm32.c:181:2: error: 'periph_addr_adj' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
181 | switch (increment) {
| ^~~~~~
drivers/dma/dma_stm32.c:161:2: error: 'memory_addr_adj' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
161 | switch (increment) {
| ^~~~~~
Fix by initialzing periph_addr_adj and memory_addr_adj to 0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
