The i2c5 instance are used on arduino connector of
stm32mp157c-dk2.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@linaro.org>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds pinmux defines for all the external ADC lines
supported by stm32. All defines are named after the datasheet of the
corresponding product lines.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Implementation of pinmux for the stm32mp157c_dk2 board.
Some UART pin mux definition has been added (mainly for
UART console and UART/SPI Arduino shield support).
This can be completed with pin mux for other stm32mp157c
UART.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since STM32_OSPEEDR_VERY_HIGH_SPEED flag is required for all I2S_CK
pins, lets add this to the STM32F4 pinmux header and remove the
duplicates in board files. While we are at it, let's add the missing
pinmux definitions for I2S_2 also.
Fixes: #9028
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Reformat L4 pinmux to be consistent with other pinmux files,
and for a better reading.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Fix issue #9028: last bit of SPI/I2S transaction may be corrupted.
Impacted STM32 SOC series: F0/F1/F2/F3/F4/L0.
Notes:
- F2/F4/L0: set gpio to very_high speed ('11')
- F0/F3: set gpio to high speed ('11').
- F1: set gpio to 50MHz.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added UART4 alternate pin function for L4 µC for PC10 and PC11.
Corrected naming of previously defined UART4 TX and RX defines.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Supported PWM at pins A0, D3, D5 and D6 which are also Arduino
compatible. Also the onboard red LED can be used with PWM.
The basic/{fade_led, blink_led} samples to apply to this board
seemlessly and operate on the onboard red LED.
Also supported RTC.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
Clean up a left over from GPIO driver factorization.
Definition of GPIO_REG_SIZE and GPIO_PORTS_BASE do not need anymore
to be spread accross SoCs.
Put these definitions directly in STM32 pinmux driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
All series STM32 have mostly the same GPIO architecture
and can share the same code for GPIO manipulation.
Functions of the external interrupt line control are also the same.
This patch extracts common code from them and put them into the 'common'
folder.
Functions of control GPIO of these series scattered in
soc/arm/st_stm32/stm32xx/ folders contain these functions:
stm32_gpio_flags_to_conf(), stm32_gpio_configure(), stm32_gpio_set(),
stm32_gpio_get, stm32_gpio_enable_int().
This patch merges them into the gpio_stm32.c file.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f723e_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f769i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Add pin muxing for STM32F302x8 by sharing most of the definitions
of the STM32F303xC. Add USART3 for both the 302x8 and the 303xC.
Add a PWM that is specific to the 302x8.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>