If shell is enabled then enable all sub-shells if their dependencies are
satisfied. This was done for some modules and subsystems but was not
consistent.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Include stm32XXxx_ll_utils.h in soc.h for every stm32 SoC,
if CONFIG_HWINFO_STM32 is selected.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Make the NRF hwinfo driver depending on !TRUSTED_EXECUTION_NONSECURE
because the FICR registers are not accessible from the non-secure
world.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Introduce the HWINFO_HAS_DRIVER Kconfig symbol to get
the information if hwinfo is supported on the current platform.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds driver supporting reading DNA ID value for LiteX SoC
builder.
Signed-off-by: Jakub Wegnerowski <jwegnerowski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
ESP32 can sport up to 4 network interfaces: two 802.11 (station and
ap), ethernet, and bluetooth. All of them derive from the same RDATA
register in efuse block 0. However, in most cases, the last (sixth)
octet will change like so:
- 802.11 station: mac[5] += 0
- 802.11 ap: mac[5] += 1
- bluetooth: mac[5] += 2
- ethernet: mac[5] += 3
Read "Number of universally admnistered MAC address" section in esp-idf
documentation[1] for more information.
[1] https://docs.espressif.com/projects/esp-idf/en/latest/
Signed-off-by: Leandro Pereira <leandro@hardinfo.org>
Add driver support for Atmel SAM0 device ID, which is 16-bytes long.
The device ID can simply be read from memory at a known location, but
the location is only described in the data sheet, not in ASF.
For SAMD2x it's 0x0080A00C, 0x0080A040, 0x0080A044 & 0x0080A048.
For SAMD5x it's 0x008061FC, 0x00806010, 0x00806014 & 0x00806018.
This adds a new property to the device tree to define the device ID
registers for this SoC family.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Add driver support for Atmel SAM device ID, which is 16-bytes long. On
this SoC family, the device ID is part of the flash controller and
complex to read. Therefore the driver reads it once at boot time and
then just returned the copy saved in RAM.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use LL drivers instead of HAL driver because LL driver is available
for all soc while HAL driver is not.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The hwinfo shell uses shell functions and thus doesn't build when
CONFIG_SHELL=n. Fix that by adding a dependency on SHELL.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add driver support for kinetis ID device.
The length depends on the SoC.
`SIM_GetUniqueId` was not used because the struct would reorder
the ID and makes the driver more complicated because the length
of the struct depends on the SoC.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit adds support for device id shell command.
Example:
uart:~$ hwinfo devid
Length: 12
ID: 0x1b0320d51485330313420
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit adds a new hardware info API.
With this API it is possible to read out the device ID.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
