If carrier is ON or OFF, then tell this information to upper IP stack
so that it can act accordingly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Don't hard code the syslog level to DEBUG, instead use the
CONFIG_SYS_LOG_ETHERNET_LEVEL setting like other ethernet drivers.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Native POSIX echo server sends malformed response to echo request of
size larger than 128 bytes (default size of each network data
fragment). Wireshark notices that by tagging echo request with "No
response seen". This commit fixes that issue.
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
Convert couple of MSEC() calls to K_MSEC() as the timeouts
when using MSEC() are just too long.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In case ethernet cable is unplugged, stm32 ethernet driver triggers
an error, driver initialization fails and fw crashes.
This could be enhanced as in case not cable is connected, HAL
returns a Time out, and will resume its initialization when
cable is plugged.
Treat HAL timeout in ethernet driver initialization as a
recoverable error and continues driver init when it happens.
Tested with sample/net/dhcpv4_client. Start board with cable
unplugged. Wait some time before plugging the cable. DHCP request
is correctly performed when cable is plugged.
Fixes: #7127
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
- tx_tsv is never used anywhere
- and rx_rsv can be allocated on stack
Optimizing a bit the stack usage in eth_enc28j60_rx() function as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
SPI API helps to directly transfer bytes from/to relevant buffers, so
let's take advantage of it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Driver is still a bit messy, not using for instance the 0-copy
capabilities of SPI API, but this will be fix later.
Constify most of the spi buf structures, removing useless variables,
renaming function with common prefix eth_enc28j60_ etc...
It seems to fix an issue on verifying if tx was successful as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Curently only link speed is exposed.
Opportunity taken to remove any post-fix enumerating the iface init
and/or the api: these must be generic and used by all the instances.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Set the received network packet priority according to VLAN priority.
Currently this mapping is 1:1 but can be changed if needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This enables / fixes VLAN support in mcux ethernet driver.
The commit contains these changes for enabling VLAN:
* Increase the size of the ethernet frame if VLAN is enabled.
* Enable VLAN in chip if VLAN is enabled
* If VLAN is enabled, then the iface in context struct should
not be used directly as there can be multiple VLAN iface
related to this physical device.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Let's use the new SPI API and ditch the old one.
Signed-off-by: Matthias Boesl <matthias.boesl@gmail.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As the native_posix board has ethernet driver, then enable it by
default if networking is enabled in prj.conf file. This way we can
use generic networking config file when running the application
for native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move IP address settings from net_if to separate structs.
This is needed for VLAN support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We can just use polling mode with 0 timeout when waiting data
to arrive from host OS. The 50ms timeout is not needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create infrastructure that allows ethernet device driver to tell
if it supports network packet checksum offloading. This applies only
to IPv4, UDP or TCP checksums. The driver can enable/disable checksum
offloading separately for Tx and Rx network packets.
If the device (ethernet in this case) can calculate the network
packet checksum for IPv4, UDP or TCP, then do not calculate the
corresponding checksum by the stack itself.
Fixes#2987
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to verify that the configuration is proper if we are
compiling the driver for unit test and not going to ever run
the test.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This creates zeth network interface in your host and allows user
to send and receive data sent to this network interface.
Fixes#6007
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use "select USE_STM32_HAL_ETH" to select the needed STM32 HAL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Amend stm32 ethernet driver with small changes:
*Provide HAL_ETH_Init return value in error message,
return on error and move it before thread creation
*Provide computed MAC address in debug message
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
IPv6 mcast addr to MAC mcast conversion was factored out to
subsys/net/ip/l2/ethernet.c for reuse by other drivers.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Now that proper solicited-node multicast group joing is implemented,
promiscuous mode's purpose is reduced to just debugging needs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If we were trying to send max MTU size data, then the temporary
frame_buf was overflowing because it only allocated 1500 bytes
for the buffer but then copied 1514 bytes into it (max mtu +
ethernet header).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With logging enabled, this leads to type mismatch warning, which is
promoted to error when building under CI.
Also, reomove extra "\n" from the logging messages.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The ethernet HAL has a different uint32_t typedef than Zephyr's u32_t:
uint32_t in the HAL is long unsigned int, while in Zephyr it's
unsigned int. This is causing a build warning on GCC ("warning:
passing argument 2 of ‘ENET_GetRxFrameSize’ from incompatible pointer
type") when passing a u32_t* where ENET_GetRxFrameSize expects a
uint32_t*.
Add a cast to silence the warning.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Until Zephyr has infrastructure to enable/disable the
reception of multicast frames we disable the hardware
multicast frame filter completly and pass all multicast
frames to the upper layer and let that deal with them.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
