The disco_l475_iot1 board uses the vl53l0x sensor in XSHUT pin
master control configuration mode. So, it has to explicitly
enable it now.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adds a board-level config option to select whether the code gets linked
into internal instruction tightly coupled memory (ITCM), external
hyperflash, or external qspi flash. The default is ITCM.
Note that we are not yet building an image vector table (IVT) into the
image, therefore the zephyr binary is not bootable by the SoC ROM as-is.
However, the DAPLink firmware prepends an IVT to the image when you use
its drag-and-drop feature to program flash, and this results in a
bootable zephyr application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds flexspi and semc memory controllers to the i.MX RT SoC. Adds
hyperflash, qspi, and sdram external memories to the mimxrt1050_evk
board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Previously, when !CONFI_XIP, BOOTLOADER_SRAM_SIZE was defaulted
to 16 (K), reducing the size of SRAM available for the program.
Also, though it has no effect, the value for SRAM start in the
dtsi file was incorrect.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The frdm_k64f board document incorrectly listed spi signals on PTCD
pins, which don't exist. They should be on PTD pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Until now, Zephyr has used a patched Kconfiglib that turns 'source' into
a globbing source (by replacing 'source' with 'gsource' at the token
level). There's two problems with this:
- The patch needs to be maintained separately
- Misspelled filenames are silently ignored, as they look like glob
patterns that don't match anything
Fix it as follows:
1. Replace all 'source' statements that use wildcards with 'gsource'
2. Remove the custom Kconfiglib patch so that 'source' no longer globs
The sed pattern '/source.*[*?]/s/source/gsource/' was run over all
Kconfig* files to do the replacement.
source's that use environment variables that might contain glob patterns
were manually changed to gsource.
Building the docs in doc/ is a good test, as doc/Makefile deliberately
sets the environment variables to glob up as many Kconfig files as
possible.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
This patch adds DT description of generic storage flash
partition. This fixes issue #7227.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
FS_FLASH_MAP_STORAGE keyword enables the storage partition,
but it was depend on flash_map module which is unused by
NFFS. This patch makes it independent thanks
to it is possible to enable the storage partition
without flash_map module.
FS_FLASH_MAP_STORAGE was renamed to
CONFIG_FS_FLASH_STORAGE_PARTITION
as it is independent for flash_map.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add support to enable test application selectively based
on defconfig
Change-Id: I8111750ff099edd95ffa22c6e312999c801678ea
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A brief description about intel_s1000 and ways to connect,
flash, debug etc.
Change-Id: I459c64d8d9574bc3511da7f983d68e044cacc1d0
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable the CAVS I2S on intel_s1000. Also, introduce a test to
validate I2S in ping-pong and normal modes.
Change-Id: Iea78e22cedc7724c1c2e821c68d7030cc0a65047
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable the CAVS DMA on intel_s1000. Also, introduce a test to
validate the DMA.
Change-Id: I2ff233c45cfd8aea55e254d905350a666aa649a0
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patchset creates Debug, Debugserver and Flash scripts
ensuring support in the ZephyrBinaryRunner mode.
Change-Id: Ib4f7820b1c6a045bd67cf4a031be99cf61e65eca
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 has multiple levels of interrupts consisting of core, CAVS
Logic and designware interrupt controller. This patchset modifies
the regular gen_isr mechanism to support these multiple levels.
Change-Id: I0450666d4e601dfbc8cadc9c9d8100afb61a214c
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 makes use of DesignWare IP for I2C.
Change-Id: Ie091318c5959b95e1febeb5cefa440f35a6d144b
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable GPIO handling for intel_s1000. It uses a DesignWare IP.
Change-Id: I522534935e4ef3a56d93aca669f6de961d927481
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 uses DesignWare IP for UART. National Semiconductor
16550 (UART) component specification is followed in this IP.
Change-Id: Ied7df1dc178d55b6dbe71d729d6383ba07274ea4
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000_crb board makes use of the intel_s1000 SoC. It has
a built-in ROM which gets executed upon applying power. It then
executes the secondary bootloader followed by the FW (like zephyr).
Change-Id: If334c359b4372a56997c3b2e1eb9250e80847f07
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Following changes are necessary to use LP3943 LED driver present
in 96Boards Neonkey board
1. Enable I2C_3 interface
2. Reduce the speed of I2C_3 bus on 96Boards Neonkey. Due to some
design quirks, on board LP3943 LED driver connected to I2C_3
operates only at Standard speed of 100KHz.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
These are a direct copy from the nrf51_pca10028 board, since it's also
an nRF51 and has the same size flash.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The allowed values for APB2 prescaler are: 1, 2, 4, 8, 16.
Set APB2 prescaler value to 1 in boards defconfig.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The NFFS partition at the end of flash is also useful for any other
file system or even the Flash Circular Buffer (FCB). Rename the
partition from 'nffs_partition' to 'storage_partition' and make it
depend on a new hidden Kconfig entry which the relevant users will
select (such as NFFS and FCB).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In some BLE use cases, using MSI driven SYSCLK is required.
Rework board Kconfig.defconfig in order to enable use of 2
alternate default clock configurations.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We have been combining imported mcux drivers into a flattened directory
structure to maximize driver reuse, but the introduction of additional
nxp soc families (lpc and imx) to zephyr has introduced driver naming
conflicts. This caused us to rename and modify imported files, such as
fsl_gpio.c/h, to make them unique across all three nxp soc families.
This makes updating the the mcux drivers complicated, especially for the
lpc family.
Reoganize the mcux drivers into soc family subfolders, so we can just
copy all the drivers from an mcux distribution (which is done on an
soc-basis) into the appropriate soc family folder. Undo all of the
naming changes that occurred when lpc and imx drivers were originally
imported. Undo the accidental squashing of the kinetis watchdog and dcdc
drivers that occurred when the imx drivers were introduced.
The drawback to this approach is that we have duplicate files when the
same hw ip modules exist in multiple soc families, however there are
only few cases where this occurs, such as fsl_lpuart and fsl_trng.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes#7137
Enables the i2c drivers for these boards.
Required to enable i2c with these boards.
Tested samples/bluetooth/beacon for nrf52_pca10040
with i2c enabled.
Parameters used for enabling i2c:
CONFIG_I2C=y
CONFIG_I2C_0=y
CONFIG_I2C_NRF5=y
CONFIG_I2C_NRF5_0_GPIO_SCL_PIN=6
CONFIG_I2C_NRF5_0_GPIO_SDA_PIN=7
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.com>
Adds led and button dts nodes to all kinetis boards and removes the
now unused preprocessor macros from board.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update names of the configuration entries so that the new nRF SPIS
driver can be used on this board.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The test "net/utils" fails to build on nucleo_f103rb
due to "region `SRAM' overflowed by 8 bytes.
Disabling PWM at the board level to build the test.
Moreover, according to issue #6858, we will only configure
board valuable HW and connectors on board level and the
user should enable what is needed on application level.
Reported-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
boards/x86/arduino_101/arduino_101_defconfig currently enables
CONFIG_UART_QMSI_0_HW_FC (HW flow control on UART 0), but doesn't enable
CONFIG_UART_QMSI_0 (the UART itself), which is a direct dependency.
This means CONFIG_UART_QMSI_0_HW_FC remains disabled despite the request
to enable it, and kconfig.py prints a warning.
Enable CONFIG_UART_QMSI_0 in the arduino_101_defconfig.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The TRNG IP block in the KW41Z is really an entropy source and not
intended to be used as a general purpose random number generator
source. The block has 15 slots to read from and when the last slot
is read it has to regenerate the 15 numbers. This process takes
3-5 seconds and is blocking. The change here is to use the TRNG as
an entropy source to the XOROSHIRO pseudo random number function
and then have the KW41Z use XOROSHIRO for random number generation.
Signed-off-by: David Leach <david.leach@nxp.com>
When we added support for the HiFive1 board we forget to make sure it
had a board yaml file. Add the file so we get sanitycheck running on
the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
configuration supports the following hardware features on the Cortex M4
Core:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
The default configuration can be found in the defconfig file:
boards/arm/colibri_imx7d_m4/colibri_imx7d_m4_defconfig
Other hardware features are not currently supported by the port.
Connections and IOs:
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
was tested with the following pinmux controller configuration.
+---------------+-----------------+---------------------------+
| Board Name | SoC Name | Usage |
+===============+=================+===========================+
| UART_B RXD | UART2_TXD | UART Console |
+---------------+-----------------+---------------------------+
| UART_B TXD | UART2_RXD | UART Console |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
All boards based on STM32 should use dts for I2C and SPI.
Move CONFIG flags selection from boards to arch and select them
for all STM32 SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We run the same tests over and over again in different qemu
environemnt. Optimize the list to reduce redundant testing of the same
protocols. Picked qemu_x86 because it has userspace enabled.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We are testing and building this already using qemu_x86, no need to
build the same thing all over again.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
