In order to avoid pin configuration conflicts between peripherals,
add CONFIG_DISK_ACCESS_STM32_SDMMC flag to for each SDMMC pinmux
configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_PWM flag to for each pwm pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_I2C flag to for each i2c pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SPI flag to for each spi pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SERIAL flag to for each serial pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Update the dtsi for stm32l471 (which the higher SoCs are based on) to
support the stm32-sdmmc disk access device. Enable the device for the
stm32l496g_disco board, and update the pinmuxing.
Note that the stm32l496g_disco board also has a card detect gpio
(MFX_GPIO8), but this is not supported yet. When not specified the
driver will assume a card is present.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move all STM32 based board pinmux files into the board dirs so we are
consistent across all the STM32 platforms/boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2017-09-12 11:24:56 -04:00
Renamed from drivers/pinmux/stm32/pinmux_board_stm32l496g_disco.c (Browse further)
