This commit adds a Context Synchronization Point immediately
after the reset handler switches to use the Process Stack
Pointer, during initialization.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Adds 8 MB and 64 MB flash size options, which correspond to the two
external flashes (qspi flash and hyperflash) on the mimxrt1050_evk
board. Adds a 32 MB SRAM size option, which corresponds to the external
sdram on the board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The API in the current SDK version is rom-patched, and uses
prcm.c code in the driverlib directory.
But, the PRCMMCU3200Init() API call should be prefixed by MAP_
to allow the option to use the ROM API in a future TI SDK version.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The loop that checks the MPU region permissions incorrectly
iterates from (num_region + 1) to 1. This should be
(num_region - 1) to 0. This results in the wrong regions
being checked and possible overflow for any implementation
that uses the max region value of 0xFF.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Until now, Zephyr has used a patched Kconfiglib that turns 'source' into
a globbing source (by replacing 'source' with 'gsource' at the token
level). There's two problems with this:
- The patch needs to be maintained separately
- Misspelled filenames are silently ignored, as they look like glob
patterns that don't match anything
Fix it as follows:
1. Replace all 'source' statements that use wildcards with 'gsource'
2. Remove the custom Kconfiglib patch so that 'source' no longer globs
The sed pattern '/source.*[*?]/s/source/gsource/' was run over all
Kconfig* files to do the replacement.
source's that use environment variables that might contain glob patterns
were manually changed to gsource.
Building the docs in doc/ is a good test, as doc/Makefile deliberately
sets the environment variables to glob up as many Kconfig files as
possible.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
This commit activates the built-in stack guard on the main_thread
before jumping to it upon system initialization. Stack guard is
activated if BUILTIN_STACK_GUARD is enabled by the user. The
commit also activates built-in thread stack guards at every
context switch, if BUILTIN_STACK_GUARD enabled by the user.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Ignore stack pointer limit checking during a HardFault or NMI
exception, to allow for the Fault handling function to execute
properly.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit implements the build-in interrupt stack protection
via the native MSPLIM register in ARMv8-M MCUs that support the
Main Extension. Main stack pointer overflows will cause Stack
Overflow UsageFaults. In addition, the commit introduces a new
config option, BUILTIN_STACK_GUARD, allowing the user to enable
and use the built-in stack protection in ARMv8-M firmware.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This patchset provides Xtensa's xcc compiler support for Xtensa
projects in Cmake. This requires the below environment variables
to be defined aptly. The appropriate xcc license information also
need to be supplied.
ZEPHYR_GCC_VARIANT=xcc
TOOLCHAIN_VER=RF-2015.3-linux
XTENSA_CORE=cavs21_LX6HiFi3_RF3_WB16
XTENSA_SYSTEM=/opt/xtensa/XtDevTools/install/tools/
RF-2015.3-linux/XtensaTools/config/
XTENSA_BUILD_PATHS=/opt/xtensa/XtDevTools/install/builds/
Change-Id: Ib3c10e8095439b0e32276ff37c00eca8420773ec
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some of the SoCs specify "Enable MPU" in Kconfig for enabling MPU
support. This will create ambiguity while selecting options via
menuconfig. Hence, append SoC family name to the selection strings
to looks more elaborative.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The title for selecting the configuration options for SoC's should be
"SoC Configuration" not "Board Configuration".
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Improve the help text of ARM k-config option
CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
It seems like SEGGER is supported across all the NXP SoC families so
lets enable it across all of them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We have been combining imported mcux drivers into a flattened directory
structure to maximize driver reuse, but the introduction of additional
nxp soc families (lpc and imx) to zephyr has introduced driver naming
conflicts. This caused us to rename and modify imported files, such as
fsl_gpio.c/h, to make them unique across all three nxp soc families.
This makes updating the the mcux drivers complicated, especially for the
lpc family.
Reoganize the mcux drivers into soc family subfolders, so we can just
copy all the drivers from an mcux distribution (which is done on an
soc-basis) into the appropriate soc family folder. Undo all of the
naming changes that occurred when lpc and imx drivers were originally
imported. Undo the accidental squashing of the kinetis watchdog and dcdc
drivers that occurred when the imx drivers were introduced.
The drawback to this approach is that we have duplicate files when the
same hw ip modules exist in multiple soc families, however there are
only few cases where this occurs, such as fsl_lpuart and fsl_trng.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that other work has eliminated the two cases where we had to do a
reschedule "but yield even if we are cooperative", we can squash both
down to a single _reschedule() function which does almost exactly what
legacy _Swap() did, but wrapped as a proper scheduler API.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
There was a somewhat promiscuous pattern in the kernel where IPC
mechanisms would do something that might effect the current thread
choice, then check _must_switch_threads() (or occasionally
__must_switch_threads -- don't ask, the distinction is being replaced
by real English words), sometimes _is_in_isr() (but not always, even
in contexts where that looks like it would be a mistake), and then
call _Swap() if everything is OK, otherwise releasing the irq_lock().
Sometimes this was done directly, sometimes via the inverted test,
sometimes (poll, heh) by doing the test when the thread state was
modified and then needlessly passing the result up the call stack to
the point of the _Swap().
And some places were just calling _reschedule_threads(), which did all
this already.
Unify all this madness. The old _reschedule_threads() function has
split into two variants: _reschedule_yield() and
_reschedule_noyield(). The latter is the "normal" one that respects
the cooperative priority of the current thread (i.e. it won't switch
out even if there is a higher priority thread ready -- the current
thread has to pend itself first), the former is used in the handful of
places where code was doing a swap unconditionally, just to preserve
precise behavior across the refactor. I'm not at all convinced it
should exist...
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Contrary to ARMv7-M, in ARMv8-M MCUs with the Main Extension,
BusFault Status Register bits are sticky and must be cleared.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This patch changes the ARM system calls to use registers for passing
or arguments. This removes the possibility of stack issues when
callers do not adhere to the AAPCS.
Fixes#6802
Signed-off-by: Andy Gross <andy.gross@linaro.org>
During the transition of privilege levels while performing syscalls,
the ARM documentation recommends flushing the pipeline to avoid
pre-fetched instructions from being executed with the previous
privilege level.
The manual says:
4.16 CONTROL register
(...) after programming the CONTROL register, an ISB instruction
should be used.
(...) This is not implemented in the Cortex M0 processor.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The TRNG IP block in the KW41Z is really an entropy source and not
intended to be used as a general purpose random number generator
source. The block has 15 slots to read from and when the last slot
is read it has to regenerate the 15 numbers. This process takes
3-5 seconds and is blocking. The change here is to use the TRNG as
an entropy source to the XOROSHIRO pseudo random number function
and then have the KW41Z use XOROSHIRO for random number generation.
Signed-off-by: David Leach <david.leach@nxp.com>
- Removed OT_PLAT_RADIO_DEVICE_NAME
- Changed OpenThread binding to use NET_AP_IEEE802154_DEV_NAME
- Modified Kconfig chain to ensure NET_AP_IEEE802154_DEV_NAME
is enabled for both native 802.15.4 and OpenThread configurations
- Changed default setting of NET_L2_IEEE802154 in defconfig for mkw41z4.
- Fixed OpenThread api support code to use the state of mIsCcaEnabled
in the transmit frame to conditionally invoke radio_api->cc() on
transmits.
Signed-off-by: David Leach <david.leach@nxp.com>
The i.MX7 SoC is a Hybrid multi-core processor composed by Single/Dual
Cortex A7 core and Single Cortex M4 core.
Zephyr was ported to run on the M4 core. In a later release, it will
also communicate with the A7 core (running Linux) via RPmsg.
The low level drivers come from NXP FreeRTOS BSP and are located at
ext/hal/nxp/imx. More details can be found at ext/hal/nxp/imx/README
The A7 core is responsible to load the M4 binary application into the
RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer,
and get the M4 out of reset.
The A7 can perform these steps at bootloader level after the Linux
system has booted.
The M4 can use up to 5 different RAMs. These are the memory mapping for
A7 and M4:
+---------------+-----------------+---------------------------+
| Memory Name | Start Address | Size |
+===============+=================+===========================+
| TCML | 0x007F8000 | 32KB |
+---------------+-----------------+---------------------------+
| TCMU | 0x20000000 | 32KB |
+---------------+-----------------+---------------------------+
| OCRAM_S | 0x20180000 | 32KB |
+---------------+-----------------+---------------------------+
| OCRAM | 0x00900000 | 128KB |
+---------------+-----------------+---------------------------+
| DDR | 0x10000000 | 256MB |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
All boards based on STM32 should use dts for I2C and SPI.
Move CONFIG flags selection from boards to arch and select them
for all STM32 SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
srd bits start at bit 8, not bit 5.
To date we are not using sub-regions so this problem was
undetected.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Ports F and G are not present on some STM32L0 parts, so
for these parts port H external interrupt should be enabled
by writing value 0x5 instead of 0x7 to SYSCFG_EXTICRn registers
(see e.g. RM0367, 10.2.4).
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Removing ${} variable evaluation fixes the issue.
For sam4s_xplained:
Before:
/repos/zephyr/samples/hello_world/build$ make VERBOSE=1 | grep march
/repos/zephyr/samples/hello_world/build$
After:
/repos/zephyr/samples/hello_world/build$ make VERBOSE=1 | grep march
...
-mthumb -mcpu=cortex-m4 -march=armv7e-m
...
Signed-off-by: Paolo Teti <paolo.teti@gmail.com>
Move driver specific to dedicated file when relevant (i.e.: more than
1-2 options), use if/endif also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
A previous commit had mistakenly overwritten the copyright years instead
of extending the range. Fix this mistake so that the proper range is
recorded.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The existing nrf5_common.h now applies to other Nordic ICs that are not
part of the "5" family. Instead rename this to nrf_common.h to cover the
upcoming ICs that belong to other families.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use HAS_ Kconfig option as intended, those are invisible option that
signify support of a certain feature that can be selected by a hardware
or platform.
For RTT and system view this was not dont in an inconsistent way.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
STM32F0 flash driver already uses FLASH_PAGE_SIZE from HAL
in flash layout part, so CONFIG_FLASH_PAGE_SIZE is redundant
and confusing.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Move the dts.fixup back to board dir in prep for support mps2_an521.
The memory maps between the two mps2_an385 and mps2_an521 differ greatly
so its easier to just keep the fixup files with the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Kconfiglib does not support UTF-8 properly yet, so avoid issues by
removing the UTF-8 character from the name until this is fixed.
See https://github.com/ulfalizer/Kconfiglib/pull/41
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit introduces the ARM_SECURE_FIRMWARE k-option,
which indicates that we are building an ARM Secure application.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the implementation of the SecureFault
handling for ARMv8-M-based Cortex-M33. The implementation is
compiled conditionally with compile-time directive
CONFIG_ARM_SECURE_FIRMWARE, which is to signify the intention to
build a Secure image on ARMv8-M with Security Extensions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
