Add interrupt and DMA tests for GD32 boards.
Use overlay-gd32-spi-interrupt.conf when testing interrupt based transfer,
use overlay-gd32-spi-dma.conf when testing DMA transfer,
Add overlay file for GD32 boards for these tests.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Periodic enqeueu of buffers can cause a attempt to start
a new transfer even though an endpoint is already busy.
Split usbfsotg_xfer_start() into two function, one to start
next transfer and another to continue the transfers, and use
busy state flags to explicitly mark an endpoint busy.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Pending state flag was only used by the UDC nRF USBD driver.
With the introduction of busy state flag it is no longer needed
and can be removed.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Periodic enqeueu of buffers can cause a attempt to start
a new transfer to host even though an IN endpoint is already busy.
Use busy state flags to explicitly mark an endpoint busy.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The name and wording used in template can be misleading.
Use more accurate word instance instead of device since
an implementation does not necessarily have to implement
a device (in the sense of Zephyr device model), and if it
does then devicetree should be used to describe number of
instances as in the case of CDC ACM implementation.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Fixes: #53696
Create a BOARD_REVISION_CONFIG setting to be consistent with the
BOARD_DEFCONFIG setting.
This allows systems which re-uses the Kconfig module to overrule the
file to be used as BOARD_REVISION_CONFIG in same way as is done for
the BOARD_DEFCONFIG file.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Provide a Kconfig option to enable HW RX and TX checksum, which
can increase throughput performances.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The function checked several value, but the BAP spec does
not specify that these cannot be different from stream to
stream in the CIG. The function thus did nothing but needlessly
restrict the upper layers.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Previous commit dealing with cleanup (c304db56f1) was not taking
--prep-artifacts-for-testing into consideration. Fix this and make sure
we do cleanup when this option is enabled.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Set the name of binaries to be kept when doing device testing and ignore
unrelated subsystems using tags.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Have boards define what binaries should be kept for device testing. The
purpose of this is to reduce the amount of artifacts and just keep the
binaries needed for flashing a device, reducing the size of the final
payload.
A board can have twister keep multiple binaries needed for testing when
--prep-artifacts-for-testing option is used.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add missing "default y" to the Kconfig option so that it gets selected
automatically when a matching devicetree node is enabled.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Since the commit 2ed292e1be, the HSI48
clock must be explicitly enabled in the devicetree when a peripheral
that depends on the HSI48 clock is enabled.
This commit enables the HSI48 clock for the `ronoth_lodev` board
because it enables the RNG, which requires the it.
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
This reverts commit 81908cd367.
This commit introduced a regression on SOF. Value of soc_cpus_active is
set by the core X it self in functions pm_state_set and
pm_state_exit_post_ops. soc_adsp_halt_cpu can by called only by the
primary core.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
ASSERT_OK macro is confusing as it accepts additional arguments, but
don't use them. This commit removes the confusion by making ASSERT_OK
macro accept only one argument. An additional macro ASSERT_OK_MSG is
added that mandates a format string that will be printed and optionally
arguments for the format string.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Extend Friend Queue overflow test by overflow with segmented messages:
- when a segmented message is preempted by an unsegmented message;
- when a segmented message is preempted by another segmented message;
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This commit fixes issue introduced in
5d059117fd.
Use extra flag stored in user data of net_buf to control segmented
messages in Friend Queue. The initial idea with using fragments didn't
work.
This fixes the following PTS tests:
- MESH/NODE/FRND/FN/BV-08-C
- MESH/NODE/FRND/FN/BV-19-C
- MESH/NODE/CFG/HBS/BV-05-C
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This restores the 'storage' partition (16 KiB) in the stock layout
(fstab-stock.dts), removed in 9a842588fb, probably by mistake (the
commit description refers to scratch area only).
This was found when building OpenThread Co-Processor sample.
Fixes#53689
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Fix UDP TX packet count when DHCPv4 is used. Currently UDP TX counter
is only updated when net context is in use. DHCPv4 however does not use
net_context underneath, therefore it needs to update UDP TX stats on its
own.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
After fcntl.h moved to posix, there have a compiler note
on fdtable.c. As suggested in fcntl.h, instead with
zephyr/posix/fcntl.h.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
The interrupt and watchdog registers of the it82xx2 will be
remapped, so these device nodes should be separated to
it81xx2 from it8xxx2. it8xxx2 dtsi are common settings
for it81xx2 and it82xx2.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
With ETH_STM32_HAL_API_V2 avoid log error message
if error log report:
we have problems if the traffic is high
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
Due to some previous time-related header issues, we included
`<sys/time.h>` without including `<time.h>`. The latter is
necessary for `time()` (specified by both ISO C and POSIX).
Fixes#53673
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
For NPCX SMB/I2C SMB modules in FIFO mode, the registers include:
* Common registers, offset 0x00-0x0f, accessible regardless of the value
of BNK_SEL
* Bank 0 registers, offset 0x10-0x1e, accessible if BNK_SEL is set to 0
* Bank 1 registers, offset 0x10-0x1e, accessible if BNK_SEL
is set to 1
In the current driver, it uses two structures, `smb_reg` and
`smb_fifo_reg`, to access `Common + Bank 0` and `Common + Bank 1`
registers. But It might be easy to misunderstand that they are two
different modules.
This CL tries to simplify this by the following steps:
1. Use `union` to combine `Bank 0/1` registers in the same structure.
2. Remove `smb_fifo_reg`. We needn't use two structures to present
SMB registers.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Inclusion of this file is now deprecated in favor of
find_package(Zephyr ...). Update documentation appropriately.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
The boards, shields, and zephyr_module CMake modules have some issues
in their comments that can be trivially fixed up.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Add SDO block transfer support for the CANopen program download west
runner. SDO block transfers are experimental in the underlying CANopen for
Python.
Reduce the program download chunk size to half the program download buffer
size to avoid blocking IO.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The find_lsb_set is giving the position of the first '1' found,
starting from 1. "Bits are numbered starting at 1
from the least significant bit."
So that the find_lsb_set(64MBytes) is 27.
The HAL_QSPI_Init() accepts Init.FlashSize where "FlashSize+1
is effectively the number of address bits
required to address the flash memory."
To get 64MBytes = 2^26, the value of the Init.FlashSize must be 25.
and bit written to the DCR = 25.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The find_lsb_set is giving the position of the first '1' found,
starting from 1. "Bits are numbered starting at 1
from the least significant bit."
So that the find_lsb_set(64MBytes) is 27.
To get 64MBytes = 2^26, the value of the Init.DeviceSize must be 26.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Change the stm32_ospi_read_sfdp to have AddressSize
prepared in one single condition.
Add more debug msg.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
mesh_shell application has been included recently some set new
abilities that added more functionality for testing.
That caused the application cannot fit in some supported plarforms
like qemu_cortex_m3. The reduced legacy configuration has been
added to fit stack into it. This platform is used in CI.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Function cbpprintf() returns int type and may return negative error
code. Fixes static tool warnings.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
When re-generating hardware map for DKs with more than 1 serial port (more
enries in the hardware map), then we keep enfo only about the last entry.
For boards like nrf5340 it works, because the last serial port is used,
but for nrf52840 with two ports, the first one is important, so after
re-generating the hardware map it does not work.
The solution is to keep all entries after re-generating the hardware map.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
This commit adds the support for host commands being transported
by the Serial Host Interface on the IT8xxx2 SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
This commit adds the support for host commands being transported
by the Serial Host Interface on the NPCX SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
