A few CONFIG options got set twice in sensors_n_z.conf, remove the
duplicates as we get warnings associated with this:
warning: override: reassigning to symbol GPIO
warning: override: reassigning to symbol SENSOR
warning: override: reassigning to symbol SPI
warning: override: reassigning to symbol SYS_LOG_SENSOR_LEVEL
Change-Id: I7a723218db8e365bdb45c004e93bd2c4f55ab5ac
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
select is more intuitive and easy to remember, and it is shorter too :)
Change-Id: Icc79e5cb88163344c1e2fcf65e313c33c4afa2cc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The ICCM memory, when present, can be both written and read,
so changing the attributes to be read-write-execute.
Change-Id: I432bd36f4a6ef632b7c4ce3bf8aa138895d52642
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
I've moved the call for icache_setup from nanoArchInit() to
_PrepC(), because there is a lot of code executed now before
nanoArchInit() is called, and all this time the i-cache would
be off. It should be turned on as early as possible to make
initialization faster.
Change-Id: I76a809d57a1bf9aacf51e7bb9fe8c8425f37aa13
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
The main, idle, interrupt and workqueue call stack definitions are not available
to applications to call stack_analyze() on, but they often require to be
measured empirically to tune their sizes in particular applications and
use cases.
This exposes a new k_call_stacks_analyze() API call that allows the
application to measure the used call stack space for the 4
kernel-defined call stacks.
Additionally for the ARC architecture the FIRQ stack is also profiled.
Change-id: I0cde149c7366cb6c4bbe8f9b0ab1cc5b56a36ed9
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This patch moves pwm driver samples to samples/basic and also convert
documentation of PWM samples to RST.
Jira: ZEP-1536
Change-Id: Ib2b3ff8b1722a26618e9a6fe416e2138d82ca28b
Signed-off-by: Punit Vara <punitvara@gmail.com>
Includes for HCI drivers are found in include/drivers/bluetooth/.
Change-Id: I80ef8c60aa972f0f4d625c998dac5a3896fb2ab4
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This had been erroneously reported as a build error.
Issue: ZEP-1460
Change-Id: Idddaf833011beb1165bd766dd115c021c5b90cdf
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This will replace the current goal of 'make qemu' with 'make run' and
moves Qemu handling into its own file and into the boards instead of
being architecture specific.
We should be able to add new boards that support some other type of
emulation (by adding scripts/Makefile.<emu type>) and allow the board to
define their own options for the use type of emulation.
'make qemu' will still work, however it will be deprecated, starting
with this commit it is recommended to use 'make run'.
Jira: ZEP-359
Change-Id: I1cacd56b4ec09421a58cf5d010e22e9035214df6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the existing debugserver target also for Qemu debugging. Qemu
should be maintained as one of many emulation/simulations platforms and
emulation should be abstracted in the Makefiles and not tied to Qemu.
qemugdb will still work, it is however being deprecated.
Change-Id: I0cd10fb66debb939b8f7f1304bf2ef4605da6a1d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Re-add board documentation and integrate into the project online
documentation.
Setup sphinx to pick any new board documentation added to boards/*.
Change-Id: Id208d5ef923f8806135879dd33a55ed527dc5f27
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
These samples/tests fail to build on some of the nRF5x platforms. We
don't need Bluetooth enabled for these tests so we can reduce footprint
by turning it off.
Change-Id: I87e62a1d70f80d2bc22414d6a9e591e36ad9fa06
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The 16k RAM nRF51 variants pose a challenge to get applications to fit
within the available memory. Make the default ISR stack size smaller
than the previous 2k default, but big enough to run fully functional
Bluetooth controller and host stacks.
Change-Id: Ie7c5bb21a3ba620d283e6228a2482d280f85119d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
RAM size has increased on arduino_101_ble which causes it to no longer
be able to build test_controller_dbg.
Change-Id: Iab8ed2857db23d048cfa6b04e2d1fea31efbb13c
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On the nRF5x platforms we need always need the NRF_RTC_TIMER and it
depends on the CLOCK_CONTROL_NRF5. So enable all of these always.
Fixes issues if one tries to build nRF5x platforms w/o CONFIG_BLUETOOTH.
Change-Id: I0f9af785e785f37ec289a935ddf70ee6dec08cd4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These two fields in the thread structure control the preemptibility of a
thread.
sched_locked is decremented when the scheduler gets locked, which means
that the scheduler is locked for values 0xff to 0x01, since it can be
locked recursively. A thread is coop if its priority is negative, thus
if the prio field value is 0x80 to 0xff when looked at as an unsigned
value.
By putting them end-to-end, this means that a thread is non-preemptible
if the bundled value is greater than or equal to 0x0080. This is the
only thing the interrupt exit code has to check to decide to try a
reschedule or not.
Change-Id: I902d36c14859d0d7a951a6aa1bea164613821aca
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Some thread fields were 32-bit wide, when they are not even close to
using that full range of values. They are instead changed to 8-bit fields.
- prio can fit in one byte, limiting the priorities range to -128 to 127
- recursive scheduler locking can be limited to 255; a rollover results
most probably from a logic error
- flags are split into execution flags and thread states; 8 bits is
enough for each of them currently, with at worst two states and four
flags to spare (on x86, on other archs, there are six flags to spare)
Doing this saves 8 bytes per stack. It also sets up an incoming
enhancement when checking if the current thread is preemptible on
interrupt exit.
Change-Id: Ieb5321a5b99f99173b0605dd4a193c3bc7ddabf4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Add global option for legacy configurations and enable by default for
backward compatibility. Disable option on tests and keep it on legacy
samples and tests.
Jira: ZEP-964
Change-Id: I0831e2aa74d438b1ac74eb762186cb220a504beb
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Disk IO functions are used by both FS and USB Mass Storage.
This patch refactors those from FS directory to a separate one.
In addition existing, config options were modified to make
stuff meaningful.
Jira: ZEP-1276
Change-Id: Ia2a2e18f3dbbbdb964c3dc0427d8138ad86134cd
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Remove legacy option and use SYS_CLOCK_EXISTS where appropriate.
Change-Id: I3d524ea2776e638683f0196c0cc342359d5d810f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Various sensor samples are hardwired to expect returned sensor values
are represented as doubles. In each case this assumption is incorrect.
Introduce a generic sensor_value to double helper function and adjust
the samples to use it.
Change-Id: I89c788686576562b84e07a36064640231340c33b
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Remove aio disabling code before calling callback. If aio is
disabled before callback is invoked, calling pending
interrupt check API in the callback will get negative result.
If user wants to disable the aio, it can do this in callback
instead of this being done blindly before callback.
Jira: ZEP-1437
Change-Id: I42ebe4584af6396ac2360152f9b0e2c389c44145
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
drivers/gpio/gpio_pcal9535a.c defines a nano_timer,
but never uses it. So delete it.
gpio_sch.c uses a k_timer, but gpio_sch.h defines a
nano_timer. So change the variable poll_timer to
type k_timer.
Jira: ZEP-1525
Change-Id: I884e4703c1ace61da5be7d9c63e58e7c3bce7f68
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
The way the PATH modification bit was set was failing unnecesarily
when the shell is being ran with -e (fail on error), which is leading
to unnecessary (and dangerous) workarounds in integration scripts.
So wrap it in an if sentence, so the shell doesn't bail out when the
grep fails to find the scripts_path in PATH.
Change-Id: Ia88a5f430e08ef4c186d11834f4cd840ccd29f7f
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This will allow inclusion of documentation files that exist outside of
doc/ and will make it possible to add rst files across the tree,
especially for boards, samples and tests.
Change-Id: I7afcf92d99f504b2bc0b2b7e3452acb2f8e08294
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In commit bf4fb51f44, "net: if: Add NET_IF_UP flag"
a reference to ctxt->iface was added in the ipsp_disconnected function.
Let's add the ctxt variable definition to fix the build break.
Change-Id: Ib06047e333504f3db4fe175fb3ef1dce347e1916
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Cut wait times by 4, in chunks in 25ms instead of 100ms. This allows to
see what is going on, but with much faster transitions, which makes the
demo slightly less boring.
Change-Id: I32fdd6e41a9af1fe9aa8a8f186de7945986b3a71
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Similar to _pend_queue, it's more efficient to do the logic inline.
Change-Id: I68ac4fbc26c97b6ec9322caef98504ff6ccc8727
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
It's calling a function on every iteration, it's more efficient to just
do the logic inline.
Change-Id: I166e377d4ffb3056749fd625cb789173030904ac
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
