The `cpu.h` is meant to be a hack around Zephyr's dependencies
for unit-test, relocate it to a folder that's included only by
unit-test.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
In ull_disable, it is imperative that the callback is set up before a
second reference counter check, otherwise it may happen that an LLL done
event has already passed when the disable callback and semaphore is
assigned.
This causes the HCI thread to wait until timeout and assert after
ull_ticker_stop_with_mark.
For certain compilers, due to compiler optimizations, it can be seen
from the assembler code that the callback is assigned after the second
reference counter check.
By adding memory barriers, the code correctly reorders code to the
expected sequence.
Signed-off-by: Morten Priess <mtpr@oticon.com>
According to the RFC, MODE_IS_INCLUDE/MODE_IS_EXCLUDE codes should be
used while sendling Multicast Listener Reports in response to a query.
When performing a transition between states (e.g., when joining or
leaving a multicast group) CHANGE_TO_INCLUDE_MODE/CHANGE_TO_EXCLUDE_MODE
have to be used.
Signed-off-by: Konrad Derda <konrad.derda@nordicsemi.no>
From RFC:
* "source list" is an unordered list of zero or more unicast
addresses from which multicast reception is desired or not desired [...]
It means that there is no need to add any special address to specify
"block all" and "allow all" states explicitly. This commit removes the
unnecessary addition.
Signed-off-by: Konrad Derda <konrad.derda@nordicsemi.no>
I got some feedback about confusion as to why the bt_addr types are not
packed. This commit adds a note about it.
This commit also adds a check for the alignof of the structs to verify
the statement 'their members are bytes or byte arrays' to thoroughly
prove that the struct is effectively as-if packed.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
The shell UART TX code would only disable the TX IRQ when no data was
available in the TX ring buffer. However, it should also disable the IRQ
when all data retrieved from the buffer has been written. Otherwise it
will just result in another immediate TX IRQ which results in the IRQ
finally being disabled.
For this to work, since ring_buf_get_claim may not always return all
available data in the ring buffer on a single call, we need to loop
until either no data is left in the ring buffer or the UART was unable
to consume any of the data.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
MBEDTLS_PSA_CRYPTO_C and MBEDTLS_USE_PSA_CRYPTO are 2 different
things and the former should not automatically enable the
latter. The reson is that the user might want the MbedTLS
PSA crypto toolbox to be built, but at the same time he/she
does not want TLS/DTLS (and other intermediate modules such
as PK, MD and Cipher) to use PSA APIs.
For this reason this commit introduces a new Kconfig option
named CONFIG_MBEDTLS_USE_PSA_CRYPTO to enable the corresponding
build symbol. By default USE_PSA_CRYPTO is disabled. It is
only explicilty enabled in tests/samples that were previously
setting CRYPTO_C (since in those cases USE_PSA was set).
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
When BUILD_WITH_TFM is enabled we can dispatch hash computation
to TFM. This allows to remove the built-in support of SHA256 from
the non-secure side (if it's not used for any other purpose, of course).
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Moving toward the adoption of PSA crypto APIs, TinyCrypt is going
to be deprecated so we can remove it in favor of newer APIs.
Moreover tls_credentials is mostly meant to store data in the
protected storage meaning that there is a TFM implementation
providing this service. The same TFM can of course be used to
compute sha256 hashing thus saving memory footprint on the NS
side by removing TC.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
When using the TLS_CREDENTIALS_BACKEND_PROTECTED_STORAGE there is
BUILD_WITH_TFM enabled which means that we can take advantage of
TFM (thorugh PSA interface) to compute the SHA256 hash.
This removes the need for the built-in implementation of
mbedtls_sha256() on the non-secure image (unless it's used somewhere
else, of course) and therefore it helps in reducing the memory
footprint.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Add support for gratuitous ARP transmission by Zephyr network stack.
This allows to prematurely fill the peer ARP table, so there's no need
to send an explicit request when peer needs to send an actual packet.
The gratuitous ARP is send when the network interface is brought up
(joins the network) or a new IP address is added. The gratuitous ARP
request is also sent periodically, with a configurable interval time.
The gratuitous ARP should also be sent whenever MAC address of the
interface is changed, but as Zephyr only allows to do this when
interface is down, this is already covered by the first case (interface
brought up).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Implement LL_ASSERT_INFO1 and LL_ASSERT_INFO2 for triggering assertions
with parameter information provided for vendor core dump.
Adds Kconfig CONFIG_BT_CTLR_ASSERT_VENDOR by which the new LL asserts
map to BT_ASSERT_VND macros, which shall be implemented in the
debug_vendor_hal.h of the platform. If not enabled, LL_ASSERT_INFO will
map to existing BT_ASSERT_MSG with parameters printed.
Add use of LL_ASSERT_INFO2 where ull_ticker_stop_with_mark() result may
assert.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Fixing the websocket command output to align the fields and
printing interface index instead of a pointer value.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add socket obj_core support to websocket so that the socket
information can be viewed by "net sockets" command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
After upgrading the HTTP connection to websocket, call the
application registered callback to transfer the ownership of
the socket to the application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If the other end closes the connection, it is not exactly an
error so downgrade the print to debug level.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The http_server needs a way to bind a websocket socket to the
upgraded http connection socket. So websocket_register() is used
for that.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use normal "config" in order to avoid this error from compliance
check script:
Found pointless 'menuconfig' symbols without children.
Use regular 'config' symbols instead.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Allow connection to be upgraded from HTTP/1.1 to websocket.
This commit does nothing yet with the upgraded connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Check what kind of upgrading we are doing and return error
if we receive upgrade that we do not support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This change works around the issue with the semaphore timeout during
the Bluetooth HCI driver initialization when the bt_enable function
is called in the context of the System Workqueue thread. This issue
only affects platform that use the IPC service and its ICBMsg backend
(e.g. the nRF54H20 DK target).
The bt_enable function, when called in the System Workqueue context,
results in a deadlock, as the waiting semaphore of the Bluetooth HCI
driver times out:
bt_hci_driver: Endpoint binding failed with -11
During the Bluetooth HCI driver open operation in the context of the
bt_enable function, the driver code waits using the semaphore for the
endpoint binding process of the IPC service module to finalize. The
issue occurs when the waiting occurs in the System Workqueue context.
The ICBMsg backend from the IPC service schedules a system work during
the endpoint registration, in which it finalizes the binding operation
- also in the System Workqueue context. As the Bluetooth HCI driver
with its wait operation keeps the System Workqueue context busy, the
endpoint binding cannot be completed by the ICBMsg backend before the
HCI driver semaphore timeout.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
When building ISO applications on a device that has the host
and controller on the same core, the application developer
shouldn't have to set controller specific configurations.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
`OPENTHREAD_PLATFORM_KEY_REF` should not be selected for RCP
architecture, as keys are handled on host's side and passed to
device over Spinel, and therefore they cannot be exported
on platform from reference with PSA Crypto API.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
Part of the initialization is done in the static usb_device_init()
function called by SYS_INIT(). We can move part of it, which initialize
the descriptor and calls usb_set_config(), to usb_enable(). This allow
some usb_get_device_descriptor() dependencies called at application
desired point.
Also make sure that usb_fix_descriptor() is called only once.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
These relocations are needed e.g. when an LLEXT is built from
multiple files and they share data objects.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Add missing break inside switch statement to allow UDC context to
indicate that current operating speed is High-Speed. Due to missing
break statement, the stack always assumed Full-Speed.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Two issues fixed:
When pull-context is created, it does not have to wake up the RD
client context. Ignore the EPERM warning.
When new pull-context creates a new socket, sometimes socket-loop
gets to recvfrom() before we have set O_NONBLOCK on the socket.
So use ZSOCK_MSG_DONTWAIT on zsock_recvfrom() so it does not
block the socket loop.
Fixes#71450
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Modem chat scripts should be able to add a script command which
is simply a delay. The validation of chat scripts currently
disallows chat script commands which only have a timeout set.
Update modem_chat to allow modem chat script commands which
only have a timeout. Additionally do a bit of cleanup to
remove duplicate code.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
net_buf_alloc(K_FOREVER) can now fail (if run from the syswq). Propagate to
the caller instead of asserting.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
It may happen that the interface is up but not yet running
when we issue the rejoin_ipv6_mcast_groups(). This can be
fixed by calling this function again right after the iface
is set to 'running' state in the notify_iface_up handler.
Signed-off-by: Marcin Kajor <marcin.kajor@nordicsemi.no>
This sets the number of arguments for SMF_CREATE_STATE() to always
be the same, independent of the selected Kconfig options.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
The `BT_DEBUG_*` Kconfig symbols have been deprecated for more than 2
versions, remove them.
Update code that was still using them.
Remove the Bluetooth specific `Kconfig.template.log_config_bt` and use
`Kconfig.template.log_config_inherit` from the logging subsystem
instead, now that the legacy symbols can be removed.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Add the CAP commander reception start procedure which starts reception
on one or more CAP acceptors
With the implementation of broadcast reception start procedure we also need
some mockups for unit testing
Signed-off-by: Andries Kruithof <andries.kruithof@nordicsemi.no>
This commit fixes the incorrect include path for the fuse library.
pkg_search_module populates the <XXX>_INCLUDE_DIRS cmake var.
Signed-off-by: Russ Webber <russ@rw.id.au>
When calling net_if_get_default(), print a warning if no
network interfaces are found. This helps debugging mysterious
crashes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
When trying to get IPv6 prefix, if there are no network interfaces
then the net_if_get_default() will return NULL but we should not
crash at that point but return gracefully.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Making default preferred time much closer to default valid time
so that the served addresses are much shorter time in deprecated
state where they cannot be utilized. This is important in Zephyr
as there are limited number of IPv6 addresses that can be allocated
to the network interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The local address used for established TCP socket needs to be
dig out from TCP internals and not from context->local.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
We usually cannot use context->local for established TCP connections
because the local address is not updated for TCP if we are bound to
any address. So create helper that try to figure out the end point
addresses.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
