Enable WPS PIN expire timeout parameter, this helps us in cleanup of
the Authorized MAC IE in the beacon in case no peer is connected
within the timeout.
Without this parameter the IE is not removed from the beacon.
Signed-off-by: Gaofeng Zhang <gaofeng.zhang@nxp.com>
Added support for SPI in 4-wire and 3-wire configurations to
the Infineon AIROC WiFi driver (drivers/wifi/infineon).
Review changes:
Move DT_DRV_COMPAT to common header file
Correct board-specific preprocessor lines
Removed AIROC_MAP_COUNTRY_CODE
Move Pico W configuration details to devicetree
Use pinctrl to manage shared data/interrupt GPIO
Clean up bus selection in Kconfig.airoc
Make SDIO and SPI bus struct independent
Replace LOG_DBG with LOG_ERR
Remove functionally duplicate operation
Remove spurious Kconfig option
Minor cleanup in CMakeLists.txt
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Combine BLE and 802.15.4 monolithic build under a single config to make
it less error prone.
The choice between a BLE/802.15.4 combo firmware and a BLE only firmware
is done depending on the Soc (like RW610 vs RW612).
Signed-off-by: Axel Le Bourhis <axel.lebourhis@nxp.com>
1) Unless ACS is being used, both "channel" and
"vht_oper_centr_freq_seg0_idx" parameters must be set.
Fixed "channel center segment 0" not being set in VHT Operation IE.
2) Set HT capabilities and VHT capabilities via the wifi ap config command.
3) Set AP bandwidth to wifi driver via the wifi_mgmt_api->ap_config_params.
Signed-off-by: Gang Li <gang.li_1@nxp.com>
MDK 8.68.1 uses nRF54L15_XXAA symbol for determining whether
given errata is applicable or not for nRF54L Series SoCs.
This causes all erratas to be disabled for nRF54L05 and nRF54L10.
To mitigate this DEVELOP_IN_NRF54L15 symbol needs to be defined,
and removed once new MDK is integrated.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
The signature of callback and the callback function is now changed, so,
add a wrapper to convert b/w them.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
MbedTLS Crypto ALT implementation clearly states that DPP3 isn't
supported, remove DPP3 to fix a build error related to HPKE.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
These files are now unconditiaonlly included, the defines within the
file takes care of both enable and disable of the feature.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This commit is to enable Ethernet drivers support on Renesas RA
MCU, first target support is the Renesas RA8 series
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Add support for mdio driver for Renesas RA MCU series
This support utilize the r_ether_phy driver in hal renesas
to support mdio write and read function
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The nrf wifi drivers include code related to qspi/spi bus. This work
moves bus related files to a new nrf70 bus library which is now
independent of the core driver and facilitlates building applications
directly using the bus APIs, agnostic to enabling wifi configs.
Signed-off-by: Bansidhar P.M <bansidhar.mangalwedhekar@nordicsemi.no>
Commit add `modcarrier` shell command for Openthread diagnostic mode.
Command can transmit modulated carrier out of device for test purposes.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Added dppic0 node label, alongside the dppic to maintain backward
compatibility. The use of dppic0 is preferred.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Changed the CMakeLists to enable the nrfx_gppi utilities based solely on
the CONFIG_NRFX_GPPI Kconfig. This unifies the configuration on all nRF
SoC families.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
The resource reservation header is now included according to a Kconfig
value. The Kconfig can be overriden out-of-tree in case a different
header is needed.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
For the C sources the offloaded raw TX mode wasn't considered and else
case picks up system mode files causing build issues.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Added hw_mode check of AP with hostapd when getting link mode of current
station. If the hw_mode of AP is 11b, then the link mode of current
station will show 11b.
Signed-off-by: Hui Bai <hui.bai@nxp.com>
Introduced few Kconfigs that allow to change default values
of MLE child timeout and child supervision timeouts.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Make sure that `MBEDTLS_PSA_ITS_FILE_C` is not defined when
`CONFIG_SECURE_STORAGE` is enabled as the former takes precedence over
the latter in Mbed TLS (`psa_crypto_storage.c`).
This fixes usage of the secure storage subsystem by Mbed TLS on platforms
such as `native_sim`.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
This reverts commit ec0b9ccbc1.
This commit has two issues:
1. We already query signal poll just above, so, wastes time querying the
infor from the firmware.
2. Doesn't handle modes, i.e., queries even for AP mode as well.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Allow `nrfs_backend_send` to push early requests into the message queue,
but defer sending them until a connection is established, at which point
the queue will be flushed. This benefits asynchronous code by making it
optional to call `nrfs_backend_wait_for_connection` before using the
nrfs service API, which is already non-blocking.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Traditionally threads have been initialized with a PRESTART flag set,
which gets cleared when the thread runs for the first time via either
its timeout or the k_thread_start() API.
But if you think about it, this is no different, semantically, than
SUSPENDED: the thread is prevented from running until the flag is
cleared.
So unify the two. Start threads in the SUSPENDED state, point
everyone looking at the PRESTART bit to the SUSPENDED flag, and make
k_thread_start() be a synonym for k_thread_resume().
There is some mild code size savings from the eliminated duplication,
but the real win here is that we make space in the thread flags byte,
which had run out.
Signed-off-by: Andy Ross <andyross@google.com>
Add a spinel support to an RCP design, the core of OpenThread lives on the
host processor connected to an RCP radio controller over a HDLC interface.
Signed-off-by: Jamel Arbi <jamel.arbi@nxp.com>
Currently, the serialization module for 802.15.4 enabled
the network core without giving it access to application
core memory in trusted execution mode. This commit
grands this access.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
Adding new CONFIG_MBEDTLS_PSA_KEY_SLOT_COUNT to select the number
of key slots in PSA Crypto core. The default value is 16. Be aware
that key slots consume RAM memory even if unused, so the proper value
should be a compromise between the number of slots required by
the application and the available RAM in the system.
This commit also:
- updates tests/crypto/secp256r1/mbedtls.conf to showcase how to
use this new symbol to reduce RAM footprint.
- tests/bsim/bluetooth/mesh/overlay_psa.conf to support all the
keys used in the test.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Adding the Kconfig symbol CONFIG_MBEDTLS_PSA_STATIC_KEY_SLOTS
to allow Mbed TLS's PSA Crypto core to use static key buffers
to store key's material. This helps reducing heap memory
usage and, potentially, it also discard code implementing
heap memory management if there's no other module in the build
that makes use of it.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
The shim files should be part of the Zephyr module directory within
Zephyr, as they are coupled with the module implementation which os OS
agnostic.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
