For the !SOC_I2C_SUPPORT_HW_CLR_BUS in which we implement bus
reset via GPIOs, change the devicetree properties to be actual
gpio properties and update the code to reflect this.
Signed-off-by: Kumar Gala <galak@kernel.org>
This commit adds the pll2 and pll3 clock control nodes
with st,stm32u5-pll-clock compatible.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit changes the range for stm32u5 pll divider values
to allow divider value of 1.
- DIVQ is allowed to beconfigured 1 for all PLL instances
- DIVR can be 1 for PLL2 and PLL3, but is not valid for PLl1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
We have drivers for "nxp,lpc-rtc" and "zephyr,native-posix-counter"
devicetree compatibles, however we had no bindings for them. Add
simple bindings
Signed-off-by: Kumar Gala <galak@kernel.org>
Two files ending with yml while the rest is ending with yaml, just
rename those two to avoid special handling.
Fixes documentation build.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL adds a DT node, 'power_leakage_io', which property,
'leak-gpios', contains GPIOs that have leakage current. In oerder to get
better power consumption, npcx power driver will disable the connections
between these io pads and input buffers before entering deep sleep.
Then, restore the connections after ec wakes up.
The users can overwrite this property at board DT file. Here is an
example:
&power_leakage_io {
leak-gpios = <&gpio0 0 0
&gpiob 1 0>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL configures low-voltage (1.8V) detection via GPIO driver with
GPIO_VOLTAGE_1P8 flag. It also adds support for this flag in
pin_get_config() function.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Cleanup npcx low-voltage (1.8V) detection configuration. It removes
unused soc utilities, macros, and DT node. We will configure this
feature by GPIO driver with GPIO_VOLTAGE_1P8 flag later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
ITE EC chip it81202 and it81302 both have embedded integrated
pd module (support two usbpd ports), this is different from
standalone TCPC. To prevent cc pins leakage, we disable not
active ITE USBPD port cc modules, then cc pins can be used
as gpio if needed.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Devicetree is the natural place to describe hardware, so move the
maximum frequency the SPI can work with to Devicetree instead of relying
on values from HAL.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some panels using this driver don't provide tcon/cdi/pwr/softstart
values in their reference code. It is normally expected that the right
values will be loaded from OTP in such cases. Make these values
optional to support such panels.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Introduce a generated Kconfig.dts that sets a Kconfig symbol for
every compatible.
* We set DT_HAS_<compat>_ENABLED if the devicetree has a node with
<compat> enabled. (status is okay...)
We can then use the Kconfig symbol in driver Kconfig to determine
if the driver should be available, and thus enabled by default.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Any project with Kconfig option CONFIG_LEGACY_INCLUDE_PATH set to n
couldn't be built because some files were missing zephyr/ prefix in
includes
Re-run the migrate_includes.py script to fix all legacy include paths
Signed-off-by: Tomislav Milkovic <milkovic@byte-lab.com>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add configuration for SPI connected ADXL345 accelarator sensor
as adi,adxl345-spi.yaml.
Rename original adi,adxl345.yaml that configured for I2C
rename to adi,adxl345-i2c.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Implement support for SAMR34 and SAMR35 parts, tested on a SAMR34
Xplained Pro dev board. Confirmed operational peripherals: UART, GPIO,
PWM, ADC.
NOTE: The SAMR34 datasheet lists NVIC line 20 for the ADC's interrupt,
but the SAML21 datasheet gives line 22. It appears that the SAMR34 sheet
is incorrect (the ADC doesn't function with line 20), and as such, I have
also omitted the adjustments for TC4 and AC...
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
Implement support for SAML21 parts, tested on a SAML21 Xplained Pro dev
board. Confirmed operational peripherals: UART, GPIO, PWM, ADC.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
The built-in USB serial peripheral is a virtual serial and does not
allow to be configured like a normal UART.
Removing the unused UART config parameters.
Also reducing initialization to single-instance only.
Signed-off-by: Martin Jäger <martin@libre.solar>
Remove 'label' property from SDHC nodes. We can use variants of
DEVICE_DT_GET to get access to a device pointer for use in an
application.
Signed-off-by: Kumar Gala <galak@kernel.org>
