Add driver for Festo VEAA-X-3 series proportional pressure regulator.
The driver assumes that the maximum ADC value matches the maximum
output from the device, and that the maximum DAC value matches the
maximum input value for the device. External hardware is probably
required between the ADC/DAC and the device.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add driver for TSic 206/306/316/506F/516/716 temperature sensor.
The driver uses PWM capture driver to read a single wire with
Manchester-like encoding.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Based on the iis2dlpc driver, with some significant differences in
interrupt handling.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
The DHT20 sensor is a temperature and humidity sensor that uses I2C to
communicate with a microcontroller. The DHT20 sensor is Aosong.
use standard crc
update description to add reference to AHT20 and AM2301B
clean code, use defines and bit manipulation
add dht20 to i2c test suite for build tests
update bit manipulation
use more defines instead of raw numbers
add bindings to allow aht20 or am2301b to be used in devicetree
in all 3 cases, the same dht20.c driver is compiled
Signed-off-by: Nathan Olff <nathan@kickmaker.net>
Add driver for Angst+Pfister O2 sensors FCX-MLD25 & FCX-MLD95 and maybe
more. Tested with FCX-MLD25.
Supports get O2 value, get status, and power management.
Note that in suspended power mode heating output is at 20 %, thus
probably not suited for a battery powered device.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The STTS22H is an ultralow-power, high-accuracy, digital temperature
sensor offering high performance over the entire operating temperature
range. This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/resource/en/datasheet/stts22h.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Implement a sensor for the output diagnostics of the low side
switch BD8LB600FS.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Add driver for ScioSense ENS160 multi-gas sensor. The driver includes
support for I2C and SPI, attributes for setting temperature and
humidity compensation and data ready trigger.
Also add ScioSense to the list of vendor prefixes.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
The LIS2DE12 is an ultra-low-power high- performance three-axis
linear accelerometer belonging to the “femto” family with digital
I2C/SPI serial interface standard output.
This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/en/datasheet/lis2de12.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds source and header files required for bmp581 I2C driver.
I have used bmp581_user.h to add more usage related definitions
but bmp581.h to add hardware related definitions.
Signed-off-by: Talha Can Havadar <havadartalha@gmail.com>
Signed-off-by: Gerhard Jörges <joerges@metratec.com>
This is a driver targetting the Bosch BMA 4-series accelerometers. It
has been specifically developed for the BMA422 but should be compatible
with others in that line, excepting the BMA400. Supports key attributes
and async RTIO one-shot operation. I2C operation is supported, with
stubs for a SPI implementation provided for future improvement.
Signed-off-by: Tristan Honscheid <honscheid@google.com>
The LIS2DU12 is a linear 3-axis accelerometer with advanced digital
functions whose MEMS and ASIC have been expressly designed to build
an outstanding ultralow-power architecture in which the anti-aliasing
filter operates with a current consumption among the lowest in the
market.
This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/en/datasheet/lis2du12.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add code to configure and program Lcu, Trgmux and Emios_Icu IPs to
get the the rotations by the motor in radians.
Co-authored-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Co-authored-by: Mayank Mahajan <mayankmahajan.x@nxp.com>
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
The LPS28DFW is an ultracompact, piezoresistive, absolute pressure sensor.
Compared to the LPS22DF, the LPS28DFW is waterproof and has a Dual FS
capability and does not have SPI. This commit extends the LPS22DF driver to
be compatible with the LPS28DFW device.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
The LPS22DF is an ultracompact, piezoresistive, absolute pressure sensor
that functions as a digital output barometer. The LPS22DF provides lower
power consumption, achieving lower pressure noise than its predecessor.
This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/en/datasheet/lps22df.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
