With this refactoring of pcie directory, RC drivers are placed under
host/ directory, EP drivers are placed under endpoint/ directory and
they are completely independent of each other.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
PCIe shell was enabled by default if shell is enabled in below commit:
commit ee985d81aa ("shell: enable modules by default if shell is
enabled").
However, this shell file has tests for PCIe RC, not applicable to EP.
So, should not be default enabled for PCIe EP.
If we add EP shell tests in future, they should be added under
drivers/pcie/endpoint/ directory.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
If shell is enabled then enable all sub-shells if their dependencies are
satisfied. This was done for some modules and subsystems but was not
consistent.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add public APIs for PCIe endpoint driver:
- EP configuration space read/write
- Mapping/Unmapping of Host buffer and PCIe outbound region
- Raise interrupt to Host
These are minimal base APIs to make PCIe EP functional.
Also, add a Kconfig and an empty CMakeLists.txt for drivers to extend.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
