Add support for the IS31FL3194 3-channel LED driver. This driver can be
configured to handle its outputs as either a single RGB LED or (up to)
three independent LEDs.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
The controller and the driver support two hardware configurations:
- one three-channel (RGB) LED
- or three single-channel LEDs
Signed-off-by: Peter van der Perk <peter.vanderperk@nxp.com>
Add support for LP5009, LP5012, LP5018 and LP5024 devices which only
differ by the number of LEDs they can control.
Also, update application sample to run on all these new supported
devices.
Based on initial work from:
- Marek Janus <marek.janus@grinn-global.com>
- Rico Ganahl <rico.ganahl@bytesatwork.ch>
Signed-off-by: Mathieu Anquetin <mathieu.anquetin@groupe-cahors.com>
Enabled support for is31fl3733 driver. This driver supports
the full LED API, and enables the following features of the is31fl3733:
- individual LED dimming
- individual LED enable/disable
- bulk writes of LED enabled and dimming states
- global LED current limit
- blanking (via custom API)
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
The IS31FL3216A is a fun light LED controller. The LED current of each
channel can be set in 256 steps by adjusting the PWM duty cycle through
an I2C interface.
Signed-off-by: Guy Morand <guy.morand@bytesatwork.ch>
Add a minimal driver for the ti lp5569 led controller. The driver supports
multiple instances. Commands on|off|set_brightness are supported.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Implement a LED driver for Microchip XEC using the breathing,
blinking LED controller. The driver supports LED on, off, and
blink API's. The BBLED block uses the 32768 Hz clock domain
allowing the module to operate in light and deep sleep states.
Blink frequency is 32768 divided by 256 * (prescale + 1) where
prescale is a 12-bit value. Duty cycle is specified by an 8-bit
value where 0 = full off, 127 is 50%, and 255 is full on.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add support for TI TLC59108 an I2C 8-bit LED driver.
Supported blinkink period: 41ms to 10730ms
Supported brightness value: 0 to 100%
This driver supports the following APIs:
1. led_blink
2. led_set_brightness
3. led_on
4. led_off
This is a modified version of the NXP PCA9633 driver.
Signed-off-by: John Kjellberg <kjellberg.john@gmail.com>
This driver supports the PWM driven LEDs. The devices are created from
the DT nodes with a compatible property matching "pwm-leds". For each
child node a LED is created and its "pwms" phandle's node is used to
retrieve the PWM configuration: channel, period and flags. If some of
this properties are missing (it is the case for some PWM controllers),
then reasonable default values are used.
This driver implements the following LED API methods:
- led_on
- led_off
- led_blink
- led_set_brightness
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
This patch introduces the "led" shell command. This allows to run the
LED API functions (and to test the LED drivers) from the Zephyr shell.
The following subcommands are supported:
- on
- off
- get_info
- set_brightness
- set_color
- set_channel
- write_channels
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
This patch adds support for the Texas Instruments LP5030 and LP5036
I2C LED controllers. They are respectively providing up to 30 and 36
channels (i.e. 10 or 12 RGB LEDs).
In addition to the channel/color registers this LED controller provides
a per-LED brigthness register. This driver implements both LED-based and
channel-based API methods:
- led_on
- led_off
- led_get_info
- led_set_brightness
- led_set_color
- led_set_channel
- led_write_channels
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit add support for the LED driver functionality of the
HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support for TI LP5562 I2C 4-channel LED driver.
Supported blinking period: 1ms - 1000ms
Supported brightness value: 0% - 100%
This driver supports the entire currently available API.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add support for NXP PCA9633 an I2C 4-bit LED driver.
Supported blinkink period: 41ms to 10667ms
Supported brightness value: 0 to 100%
This driver supports the following APIs:
1. led_blink
2. led_set_brightness
3. led_on
4. led_off
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Add support for LED APIs for controlling the LED devices. This
API can be used by the LED devices present on the chip and connected
externally via buses like I2C, SPI etc...
Following APIs are currently supported:
1. led_blink
2. led_set_brightness
3. led_on
4. led_off
Driver support using these APIs will be added in subsequent patches.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
