Change automated searching for files using "IRQ_CONNECT()" API not
including <zephyr/irq.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The TI SimpleLink SDK got updated to version '4.40.04.04' in 'hal_ti'.
This introduced renames of some functions in HAL and has to be reflected
in Zephyr drivers which make use of them.
This renames 'PRCMPowerDomainStatus' to 'PRCMPowerDomainsAllOn' in all
affected 'cc13xx_cc26xx' drivers.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Reserve the upper 8 bits of gpio_dt_flags_t for SoC specific flags and
move the non-standard, hardware-specific GPIO devicetree flags (IO
voltage level, drive strength, debounce filter) from the generic
dt-bindings/gpio/gpio.h header to SoC specific dt-bindings headers.
Some of the SoC specific dt-bindings flags take up more bits than
necessary in order to retain backwards compatibility with the deprecated
GPIO flags. The width of these fields can be reduced/optimized once the
deprecated flags are removed.
Remove hardcoded use of GPIO_INT_DEBOUNCE in GPIO client drivers. This
flag can now be set in the devicetree for boards/SoCs with debounce
filter support. The SoC specific debounce flags have had the _INT part
of their name removed since these flag must be passed to
gpio_pin_configure(), not gpio_pin_interrupt_configure().
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
PRE_KERNEL_1 is to be used for devices that have no dependencies
and do not use kernel features, such as those that rely solely on
hardware present in the processor/SOC. This commit updates these
gpios to initialize during the PRE_KERNEL_1 rather than the
POST_KERNEL. Some SoC drivers are moved to PRE_KERNEL_2 due
to dependencies.
A lot of 'other' drivers can depend on GPIOs though phandles
(such as reset lines, data or command gpios, etc...). Most of these
drivers that would need this would come up on the POST_KERNEL,
and it's likely the driver may not be up yet as it should be defined.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
Refactors all of the on-chip GPIO drivers to use a shared driver class
initialization priority configuration, CONFIG_GPIO_INIT_PRIORITY, to
allow configuring GPIO drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
Most drivers previously used CONFIG_KERNEL_INIT_PRIORITY_DEFAULT or
CONFIG_KERNEL_INIT_PRIORITY_DEVICE, therefore the default for this new
option is the lower of the two, which means earlier initialization.
Driver-specific options for off-chip I2C- or SPI-based GPIO drivers are
left intact because they often need to be initialized at a different
priority than on-chip GPIO drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Now that we generate a header that extern's all possible devicetree
based device struct we can remove DEVICE_DT_DECLARE and
DEVICE_DT_INST_DECLARE as they aren't needed anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert gpio drivers to use new DT variants of the DEVICE APIs.
DEVICE_AND_API_INIT -> DEVICE_DT_DEFINE
DEVICE_GET -> DEVICE_DT_GET
DEVICE_DECLARE -> DEVICE_DT_INST_DECLARE
etc..
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit removes API functions and macros which were deprecated in
2.2 release. GPIO drivers are updated accordingly.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Convert older DT_INST_ macro use in cc13xx_cc26xx drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding a dependency on the GPIO resource in the TI Power module, and
configuring the edge detection on pads as a wakeup source.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Use gpio_pin_t uniformly when passing pin indexes to the driver. Use
gpio_flags_t uniformly when passing flags to the driver. Change name
of pin configuration function in API function table to be consistent
with other API functions.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The only remaining port operations have dedicated API function table
entries. Remove the defines for access op (mode), and remove support
for access op from all implementations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The last external reference to these was removed when the pin
write/read functions were deprecated. Remove the syscall support, API
function table entries, and implementation from all drivers.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
These have been replaced by the appropriate call to
gpio_pin_interrupt_configure(). While the disable function could be
implemented using the new functionality, the enable function cannot
because the interrupt mode is not available. Consequently we cannot
replace these with equivalent functionality using the legacy API.
Clean up the internal implementation by removing the inaccessible
port-based enable/disable feature, leaving the pin-based capability in
place.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Updates the cc13x2/cc26x2 gpio driver and all associated boards to use
new device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Tested with:
samples/basic/blinky
samples/basic/button
tests/drivers/gpio/gpio_api_1pin
tests/drivers/gpio/gpio_basic_api
On board:
cc1352r1_launchxl
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The value of GPIO_INT_ACTIVE_LOW is 0, so the bit checking if statement
is never executed. Use GPIO_INT_ACTIVE_HIGH when checking this bit.
Fixes#16162
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
