The default values for the platform will be used when running
make *_defconfig instead of hardcoding them in the defconfig directly.
Change-Id: If2945cc11cfca787c2b93a96b502650f1dddd29d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This makes variables readable and consistent with other drivers
we have.
Change-Id: I816f133279497eafd5d5614013c8d224d5909590
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This driver naming is an exception which compared with all other drivers
we have. To keep things consistent the configuration options and variables
are renamed to <type>_<name>.
Change-Id: Ib95aa09630a507848f78d8f2c28706b545eed06d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Don't give on the semaphore if the ring buffer is full.
Fix a missing newline in a debug message.
Change-Id: Ic0030365665c32cc9f1c641f9dacffd1a1915b09
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some platforms send over \r\n for newlines, just send over the \n.
Change-Id: Ia6072eb3719a4c7dd828457cf1634d16f4eec38a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
On Galileo, there are additional GPIO pins on the legacy bridge.
This adds the config options to enable the driver for those GPIOs,
using the MMIO-based GPIO driver.
Change-Id: I0014018238a40577631bafbdf55ed0c6c0886194
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a simple driver for MMIO-based GPIO ports.
It does not trigger any interrupts due to pin level at this moment.
Change-Id: I0c439f221988817e4be72653c68257ef6ace5bde
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are 3x PCAL9535A GPIO chips on Galileo gen2 board.
This enables the driver for all of them.
Change-Id: Ie4d1aec9427e159a60322caac541b75e7ef973db
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds the driver for I2C-based PCAL9535A GPIO chip.
This currently only enables minimal set of features of the chip for
very simple input/output operations, and does not support interrupt
yet.
Change-Id: I32ea07a71a38866280a96e68cff49cb0df12b85d
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds to the configuration flags for GPIO:
() Indicates the polarity of the pin, whether it should be
normal or inversed.
() Enables pull up/pull down for the pin.
Change-Id: I2b0c57e5a539208aff7aeb4ea53050134ab404fd
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This change puts the DW GPIO Kconfig selections inside GPIO menu.
This also groups all DW GPIO related selections under GPIO_DW.
Change-Id: I776f3f6b89e1a4dc366648f8290abb27de9eceb8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This was missing an include file, which caused the macro to not
be expanded correctly. Including init.h fixes the issue.
Change-Id: I6b190e0c75828d9b6eb42a84c213dfc174510740
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Rename system.c and platform_config.c files in preparation for merging the ia32
based platforms to remove code duplication.
Change-Id: I88caf5294817e06c235379e92cd8ee7472e88028
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Change the IOAPIC driver to be initialized directly from the init
system. The function signature of _ioapic_init() function is updated
accordingly.
Change-Id: I2f824ac745926966eebb23f60445a41e1df9eb8f
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Change the LOAPIC driver to be initialized directly from the init
system. The function signature of _loapic_init() function is updated
accordingly.
Change-Id: I5ed26d53524c8526d413a05ac9a7a58dd4264c5a
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Change the PIC driver to be initialized by the init system. To be
initialized by the init system the function signature of the
_i8259_init() function needs to be changed to the standard *_init()
function signature specified by the device model.
Change-Id: I63bf1cd0ce78920fa20da94f5966e5aab4bf41b2
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
This introduces a generic driver set for console messages routed over
inter-processor interrupt (IPI) channels. These drivers bind to a
low-level IPI driver instance for the actual transport of messages.
ipi_console_sender installs printk and/or stdout hooks to forward
messages over IPI. There is currently no buffering on the sending side.
ipi_console_receiver installs an IPI callback which stashes incoming
characters into a ring buffer, which is monitored by a nanokernel
fiber. The fiber buffers the characters on a per-line basis and sends
them to either printk or stdout. Multiple instances of this driver
may be created in case you need to receive console data from multiple
CPUs.
Change-Id: Icebc110794fbe040f975101cd2ae6e78fb38645a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This interface is an abstraction for sending messages between
processors with irq-context callbacks and no definition of
protocol.
We assume that for all IPC implementations, we can send over a
message identifier and a sized data payload, and that the receiving
side gets an interrupt on an incoming message. APIs exist to indicate
the max value of the message id and how much data can be sent over a
single message.
This will be a foundation to build various high-level drivers
which can be bound at runtime to this low-level interface. Some
examples:
* IPC where IPC messages are used as a doorbell to signal new data in
a shared queue
* IPC with various kinds of message buffering and deferred message
processing via semaphores
* IPC for serial console debug output, either a byte or a message at
a time
* IPC over UARTS in a non-shared memory environment where large-ish
messages are exchanged
* Shared memory IPC where data pointers are exchanged and a protocol
for freeing the data once the receiver is done with it
The size parameter passed to ipc_send() isn't propagated to the
receiving side. The receiver needs to infer how many bytes of
data to read in the callback function based on the protocol implemented
in the high-level driver; it can be based on message ID, or bits reserved
in the message ID for the message size, or some other mechanism.
Change-Id: I9a9529beb61cdebdfb1bafd29d037f926fab3c1b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These features set are not experimental anymore.
Change-Id: Ia9e4803982f625157e78c8002c38fed1e95c4892
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
We are introducing other kinds of drivers which support a console
that isn't over a UART.
Change-Id: I0dddbdce958437b5709c5ab26252ed47d030413d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The code fragment to bind the instances of the I2C driver is not
platform specific but is driver specific.
All the information required to bind a driver instance comes from
CONFIG_ variables. Having the binding code with the driver code
avoids duplicating the code fragments in each platform where the
driver may be used.
Change-Id: I9ea132c9340437ccb292bb8f3fa3d3a2b2a794db
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
The code fragment to bind the instances of the SPI driveri is not
platform specific but is driver specific.
All the information required to bind a driver instance comes from
CONFIG_ variables. Having the binding code with the driver code
avoids duplicating the code fragments in each platform where the
driver may be used.
Change-Id: Iff40227e3e25d431ae870d585445971f35d934dd
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
The code fragment to bind the instances of the GPIO driver were being
replicated in every platform_config.c This code is not platform
specific but is driver specific.
All the information required to bind a driver instance comes from
CONFIG_ variables. Having the binding code with the driver code
avoids duplicating the code fragments in each platform where the
driver may be used.
Change-Id: Ie07a3d12d25201e82ce7074455e6c036f463851b
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Features displayed with "[EXPERIMENTAL]" should depend on
CONFIG_EXPERIMENTAL.
Change-Id: I0a86dff442014caa2fa4629138dbe29e69d5b853
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
This buffer can be examined at runtime with a debugger to see what
is going on. Helpful if there are no other working console drivers
on the system.
Change-Id: I759467a57d16204b4b316c4f6fa8b7d5e1d1d236
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This will be useful when an implementation of a generic API requires an
int as user data when such has been defined to be a pointer.
int do_something(struct device *dev, void *user_data);
When the implementation would:
int impl_do_something(struct device *dev, void *user_data)
{
int identifier = POINTER_TO_INT(user_data);
...
Change-Id: Ic892927a03ac49e95527ef8e0e817d00256aa3bb
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Match loapic.h and allow 'ioapic like' drivers to export same ioapic
interface.
Change-Id: Ia2e5380cf9c3fc72e27beb198013e7416daa6aca
Signed-off-by: heeleyth <thomas.heeley@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The c files actually check for the Kconfig variables, so there is no
need to do the checking in the Makefile again adding double logic.
Change-Id: I8521047bd575c8f9d64f7d8e5abfb5eee8a40cb3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not enable the feature by default when EXPERIMENTAL features
are enabled.
Change-Id: I0538f9f94bb47a4bc870c8974e80faf273070f91
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
When configured as GPIO_ACCESS_BY_PIN, the callback should
be called only if the pin is enabled and received an interrupt.
Change-Id: I7addeb57c8d46dddc027e9b82a92654cd210ade1
Signed-off-by: Ricardo de Almeida Gonzaga <ricardo.gonzaga@intel.com>
if printk is disabled, the variables will be unused and we will
get compiler warning.
Change-Id: I5dad791ae89d7a8c98f9e4660da472ef0caacc92
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This enables passing the value to be used when writing to CCC so it can
be configure for indications in adition to notifications.
Change-Id: Ied89faed422e5c5ec60618d512dbd3f250f50b46
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables bt_gatt_subscribe to subscribe using indication value in
addition to notification.
Change-Id: I25f3b057e36b023a79fb66b11b70716ecc299ba9
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The correct code is 0x1e not 0x1f.
Change-Id: Icee68ebd01d76a4b3ed31a54e18b1115172f5b71
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
