For autogeneration on board pages and indexes, consistency in naming is
required, few board names did not match the images of the boards.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removing this flag allows to find the spi binary generation tool
in cmake's default paths. This also aligns this CMakeList with
the version currently found in the MEC EVB
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
x86_64 supports 4 levels of interrupt nesting, with
the interrupt stack divided up into sub-stacks for
each nesting level.
Unfortunately, the initial interrupt stack pointer
on the first CPU was not taking into account reserved
space for guard areas, causing a stack overflow exception
when attempting to use the last interrupt nesting level,
as that page had been set up as a stack guard.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We need to lock interrupts before setting the thread's
stack pointer to the trampoline stack. Otherwise, we
could unexpectedly take an interrupt on this stack
instead of the thread stack as intended.
The specific problem happens at the end of the interrupt,
when we switch back to the thread stack and call swap.
Doing this on a per-cpu trampoline stack instead of the
thread stack causes data corruption.
Fixes: #24869
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add support for running the DAC loopback test case on the NXP
FRDM-K64F development board.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Enable the driver for the Kinetis Digital-to-Analog (DAC) modules
present in the NXP Kinetis K6x SoC series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add device tree nodes for the Digital-to-Analog (DAC) modules present
in the NXP Kinetis K6x series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add option for indicating that a NXP Kinetis SoC contains a
Digital-to-Analog (DAC) module.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support for running the DAC loopback test case on the NXP
TWR-KE18F development board.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Enable the driver for the Kinetis Digital-to-Analog (DAC32) module
present in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add device tree node for the Digital-to-Analog (DAC32) module present
in the NXP Kinetis KE1xF series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add option for indicating that a NXP Kinetis SoC contains a
Digital-to-Analog (DAC32) module.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Remove dts_fixup.h files that are needed anymore, remove defines that
are used, and replace defines with new DT macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board definition for the NXP LPCXpresso55S16 development
board. Only non-secure (ns) access is supported for now.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add initial devicetree for the NXP LPC55S16. Only non-secure (ns)
access is supported for now.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Kukui has two I2C ports with various peripherals including a battery
charger and a TCPCi-compatible port controller
Enable I2C so that these can be used. No drivers are provided so far.
Also update the GPIO documentation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert the usb_vbus_set function to utilize a chosen property
('zephyr,usb-device') to determine the device node that should have a
'vbus-gpios' property set for usb_vbus_set to be more than just a noop.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_USB* to just USB*.
Also fixup how USB_MAXIMUM_SPEED was defined. We should only define it
if the property exists.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is to update west.yml to point to hal_ti with the latest changes
from TI SimpleLink SDK 4.10.00.07 for CC32xx.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Move defines for _RAM_ADDR, _RAM_SIZE, _ROM_ADDR, and _ROM_ADDR into
the linker.ld and thus remove dts_fixup.h. We rework to use
DT_REG_ADDR and DT_REG_SIZE on DT_CHOSEN(zephyr_sram) and
DT_CHOSEN(zephyr_flash).
Also fixup use of _RAM_ADDR/_RAM_SIZE in newlib/libc-hooks.c.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove dts_fixup.h files that are not used (empty) or the defines aren't
used anymore and thus can be removed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
