Enable extended advertising commands in the shell and enable the
runtime check of feature support in the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When using extended advertising the connection can be established on
different PHY. In order to have an updated value of the current PHY
we need to read the PHY of the connection in the connection complete
event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add application control of initiating phy change procedure and it's
parameters.
The reasons for allowing the application control over the PHY:
- Allow changing to Coded PHY.
- Application may change PHY to react to changes in environment
to balance throughput and range.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add application control of initiating data length procedure and it's
parameters.
The reasons for allowing the application control over the data length:
- Bandwidth control adjusted based on number of active connections.
- Changing data length before switching to coded phy.
- Applying workarounds for interoperability problems.
- Controlling order of ATT MTU and data length procedures.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add Kconfig option so that the application can disable automatic
initiation of the data length procedure. This is symmetric with the
PHY auto initiation kconfig option.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Refactor setting the maximum data length parameters supported on in
auto data length procedure. This makes setting the data length of the
connection a re-usable function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
After increasing SPI speeds on LPC family SoCs, the slow clock
speeds have been removed and default clock speeds are in use now.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Attached Flexcomm SPI driver to the main clock used by the core.
This means setting the SPI clock the same value as the core clock.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
High Speed Flexcomm device that handles high speed SPI transfer are
mapped to the same High Frequency clock that the ARM core uses.
This allows for higher frequency SPI traffic.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
This fixes some cases where an integer timeout received as a parameter
was not converted to a timeout before being used in standard API.
Changes to the POSIX library were not included as that's being
reworked in a separate PR.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Originally this only dealt with constant timeouts. Add the ability to
recognize integer parameters and convert them as well.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Cloned from counter_basic_api with modifications based on DS3231
limitations:
* Only one device tested per board;
* Counter cannot be stopped or started;
* Alarms are serviced by worker thread, so are not invoked from ISR
and require that test thread yield to allow processing (no
k_busy_wait());
* Multiple Alarms test is disabled as documented in test.
Additional tests were added for DS3231-specific API.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The DS3231 is an I2C real-time clock with internal temperature
compensated oscillator, maintaining civil time to 1 s precision with
nominal 2 ppm accuracy from 0-40 Cel.
The basic functionality is exposed as a counter that is always running
at 1 Hz. Much more functionality is exposed as driver-specific API,
including the ability to translate between the time scale of the DS3231
and the time scale of the Zephyr uptime clock. This allows correlation
of events in the system clock to UTC, TAI, or whatever time scale is
used to maintain the DS3231.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
These helper functions may clarify how much data is available to read
from or write to the circular buffer of a k_pipe.
Fixes#25036
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
The Bluetooth 5.2 specification was recently released, and has a new
version identifier (11) assigned to it in the Bluetooth Assigned
Numbers.
Relates to commit fa241f0249 ("bluetooth: Add decoding for BLE 5.2
version string")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
With BT_CTLR_USER_TICKER_ID_RANGE it is possible for vendors to add a
number of ticker nodes for proprietary purposes. The feature depends on
BT_CTLR_USER_EXT.
Signed-off-by: Morten Priess <mtpr@oticon.com>
These look up tables generalize the compat2enabled map in a way we
will need to make the API more flexible in Zephyr.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Let's get the actual node status, instead of relying on enabled.
Leave enabled in place for gen_legacy_defines.py's sake.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
If a devicetree node doesn't have a matching binding we will at least
populate a common standard set of properties for that node. The list of
standard properties is:
compatible
status
reg
reg-names
label
interrupt
interrupts-extended
interrupt-names
interrupt-controller
This allows us to handle cases like memory nodes that don't have any
compatible property, we can still generate the reg values.
We limit this to known properties as for any other property we can not
fully determine the property type without a binding and thus we can't
ensure the generation for that property is correct or may not change.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This commit adds a sample application intended to present capabilities
of the flash driver for AT45 family chips and to serve as a reference
of how to make use of that driver.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add a driver that can handle several instances of AT45 family chips,
which are enabled by specifying DT nodes for them with the "compatible"
property set to "atmel,at45" and other required properties like JEDEC
ID, chip capacity, block and page size etc. configured accordingly.
The driver is only capable of using "power of 2" binary page sizes in
those chips and at initialization configures them to work in that mode
(unless it is already done).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The Gen3 (formerly "mesh") Particle product line has a header that is
structurally related to the Adafruit Feather, and is generally
compatible with Featherwing shields. Provide nexus maps for both the
native header layout, and for the subset feather header layout, and
add alias labels for the peripherals that would be referenced from
shield overlays.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This header is physically related to the Adafruit Feather, but uses a
different pin numbering and exposes a slightly different set of pins.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
referring the ARM's Systick driver, we did the following improvements:
* use 31 bits of 32-bit counter to avoid the rare but possible
overflow of elapsed(). If 32 bits val are used, elpased() may
return a wrong value. then wrong HW cycles.
* two ways to update the correct cycles
- through systick timer irq
- when systick timer irq cann't be handled because of irq
locked/disabled, call z_timer_cycle_get_32->elapsed to update
the correct cylces. no more than one counter-wrap is allowed.
* if elapsed() is not called too long (more than one counter-wrap) from
systick tiemr irq or from z_timer_cycle_get_32. The lost of HW cycles
is unavoidable.
* some detailed discussion can be found in #24332
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Fix use of DT_HAS_DRV_INST which does not exist.
Use DT_HAS_NODE_STATUS_OKAY(DT_DRV_INST(n)) instead.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The LoRa shell requires the alias 'lora0' for the default radio. Use
the same alias for the samples to make them portable across different
radios and devices.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Provide basic commands that are useful when testing a LoRa
radio. Currently, the shell supports:
> lora conf ...
> lora send ...
> lora recv ...
> lora test_cw ...
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
The LoRa shell and samples need a way to find the default LoRa
radio. Add the DT alias 'lora0' for the default radio.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Add an API to transmit a continuous wave at a fixed frequency. This
functionality is useful to test the radio in a lab setup.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Updates the fat_fs sample documentation to reflect that it can run on
multiple boards, not just the nrf52840_blip.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the fat_fs sample yaml to depend on a feature rather than
whitelisting specific boards. This implicitly extends the sample to
mimxrt10{60,64}_evk boards, since they already support the feature.
The only whitelist board remaining is the nrf52840_blip, which requires
a device tree overlay for this sample.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the fat_fs sample to move board-specific configurations to
separate files and support a shared prj.conf file.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables sdhc on the mimxrt1064_evk board. Configures pinmuxes and device
tree, and updates board documentation accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables sdhc on the mimxrt1060_evk board. Configures pinmuxes and device
tree, and updates board documentation accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit removes the redundant `LOG` and `LOG_IMMEDIATE` selections
in `prj.conf`, since the `TEST_LOGGING_DEFAULTS`, which is enabled by
default for all tests, selects `LOG` and `LOG_MINIMAL`.
This effectively allows the test to run with the default test logging
policy, set by the testing subsystem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit removes the redundant `LOG` and `LOG_IMMEDIATE` selections
in `prj.conf`, since the `TEST_LOGGING_DEFAULTS`, which is enabled by
default for all tests, selects `LOG` and `LOG_MINIMAL`.
This effectively allows the test to run with the default test logging
policy, set by the testing subsystem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit removes the redundant `LOG` and `LOG_IMMEDIATE` selections
in `prj.conf`, since the `TEST_LOGGING_DEFAULTS`, which is enabled by
default for all tests, selects `LOG` and `LOG_MINIMAL`.
This effectively allows the test to run with the default test logging
policy, set by the testing subsystem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit removes the redundant `LOG` and `LOG_IMMEDIATE` selections
in `prj.conf`, since the `TEST_LOGGING_DEFAULTS`, which is enabled by
default for all tests, selects `LOG` and `LOG_MINIMAL`.
This effectively allows the test to run with the default test logging
policy, set by the testing subsystem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Add basic driver for GIC V3 interrupt controller.
This implementation supports
- distributor, re-distributor and cpu interface initialization
- configuration and handling of SPI, PPI and SGI.
- V2 Legacy mode is not supported and uses system interface.
Current implementation supports GIC secure state only.
All interrupts are routed to Secure EL1 as 'irq' by configuring
them as Group1 Secure.
TODO:
- MPIDR based affinity routing setting.
- percpu redistributor probe
- message based SPI and SGI generation api
- EL1NS support. Legacy mode support.
- LPI/ITS is not supported.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Frame format was validated, but its length should be also validated
relevantly against the format.
Fixes#24970
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
