Removes unused instances of struct usdhc_priv in the nxp usdhc driver.
The DISK_ACCESS_USDHC_INIT macro is responsible for instantiating these
variables.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Updates the nxp usdhc driver data structure to keep a reference instead
of a copy of the constant config structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the source clock frequency variable in the nxp usdhc driver from
the config structure to the data structure in preparation for removing
the writable copy of the config structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the nxp usdhc driver to remove instance-specific conditionals
from driver functions. Now all instance-specific details, such as power
and card detect gpios, are contained in the driver config structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The check for label property is really checking to see if a device
exists and the better way to do that is to use DT_HAS_NODE(). Replace
refernces of DT_NODE_HAS_PROP(DT_INST(...), label) with
DT_HAS_NODE(DT_INST(...)).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converts the usdhc driver to the new gpio api. Updates the
device tree for the mimxrt1050_evk board to set appropriate active
high/low polarity for the power and card detect pins.
Note that the driver doesn't actually support interrupts yet. It
initializes a gpio callback for the card detect pin, but never actually
enables the gpio interrupt. This incomplete behavior is left as-is,
since the purpose of this patch is only to convert the driver to the new
gpio api, not to add new features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The usdhc driver was incorrectly post-decrementing a do/while loop
iterator, causing an extra iteration of the loop and an out-of-bounds
array access. Change the iterator to decrement within the loop instead.
Tested samples/subsys/fs/fat_fs on the mimxrt1050_evk board.
Coverity-CID: 203403
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
