stm32mp1 was adding a STM32 specific Core selection Kconfig
symbol while zephyr generic CPU_CORTEX_M4 could be used for the
same purpose.
Remove STM32 specific symbol and use generic one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32WB HCI driver requires definition of 2 RAM regions to support
use of 3 shared memory sections: MAPPING_TABLE, MB_MEM1 and MB_MEM2.
In linker.ld, under conditions of HCI driver to be enabled,
define SRAM1 and SRAM2 based on input defined in stm32wb linker.
Then define the 3 sections MAPPING_TABLE, MB_MEM1 and MB_MEM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
soc_register.h is available in most of stm32 series.
It is sometime empty or contains includes to flash_registers.h,
which is included directly with direct reference in flash driver.
soc_register.h is also included in stm32 clock drivers, but this
driver do not use direct reference to any register anymore.
Clean up these files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Unlike Cortex-M3 and Cortex-M4, in Cortex-M7 the number of
MPU regions may vary based on the implementation. This commit
adds a DTS node for the ARM MPU peripheral in the device tree
of Cortex-M7 SoCs and updates the fixup files, so we may extract
the number of MPU regions at build time. SoCs:
- nxp_rt
- same70
- stm32f7
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In kernel_arch_init() we initialize the ARM core (interrupt
setup, fault init, etc.) so we can also move z_clearfaults()
in the same function and skip invoking it in the SoC init
functions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Hex firmware file is convenient in some scenarios, like
generating signed firmware with `west sign`. So, enable
generating hex file.
Signed-off-by: Jun Li <jun.r.li@intel.com>
This commit adds driver support for ADC1 on all 8 supported series of
stm32 with resolution and conversion time selection and calibration.
Currently DMA is not supported for all series, and without it, zephyr
won't be able to catch up ADC's end of conversion interrupt, so this
version of the driver supports one channel conversion only. Users want
multi-channel conversion should use multiple sequences in their app
code.
This driver uses LL lib rather than HAL because the current HAL lib for
ADC will call HAL_DMA_* functions rather than using zephyr's common DMA
interface, so that way the driver will break the consistency of the
code.
This driver has been tested on multiple nucleo boards including
NUCLEO_F091RC/F103RB/F207ZG/F302R8/F401RE/F746ZG/L073RZ/L476RG and all
passed the test cases in tests/drivers/adc/adc_api. If the external ADC
line is floating, it may fail the tests since ADC may get 0V and the
test cases think 0 is failing. Connect it to any voltage source between
0-3.3V will help passing the test cases.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
All series of stm32 have at least one ADC instance and this commit adds
one ADC node to the root dts file of each soc, and also adds fixing up
mappings to them.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Add support for stm32mp1 basic UART API with Zephyr.
UART Console and UART shell are also supported.
Async UART API and USART support is to be done.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This commit renames the symbol CPU_HAS_SYSTICK to
CPU_CORTEX_M_HAS_SYSTICK, to look similar to all
other CPU_CORTEX_M_HAS_ options, and moves the
K-config symbol definition from arm/core/Kconfig to
arm/core/cortex_m/Kconfig.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
ARM SysTick timer is implemented by default in ARMv7-M
and Mainline ARMv8-M processors, so we include the
corresponding Kconfig symbol in arch/arm/core/cortex-M/Kconfig
and remove the selections from the Cortex-M SOCs.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
CPU_CORTEX_M does not need to be selected by Kconfig
symbols that already select a CORTEX_M variant.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add USART1 and LPUART1 nodes on stm32wb series.
Only these 2 ones are available for now on this series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add GPIO support to stm32wb series.
Only ABCDE and H ports are available for now on this series.
Accordingly, update series dtsi file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support to stm32wb series in stm32 clock_control driver.
Ip is similar to stm32l4 one but AHB bus presacler is renamed
to "CPU1" and CPU2 and AHB4 prescalers should be defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the initial SoC support for the STM32MP1 family. The code was
tested on STM32MP157c, but should work on any STM32MP1XX currently
available.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Same deal as in commit 4638652214 ("Kconfig: Use 'default' instead of
'def_bool' in Kconfig.defconfig files"), fixing new stuff that got
introduced since then.
Some symbols, like ALTERA_AVALON_PIO, are only defined in
Kconfig.defconfig files, and so need the def_bool.
Motivation (from the note at the end of
guides/kconfig/index.html#common-shorthands):
For a symbol defined in multiple locations (e.g., in a Kconfig.defconfig
file in Zephyr), it is best to only give the symbol type for the "base"
definition of the symbol, and to use 'default' (instead of 'def_<type>'
value) for the remaining definitions. That way, if the base definition
of the symbol is removed, the symbol ends up without a type, which
generates a warning that points to the other definitions. That makes the
extra definitions easier to discover and remove.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Allows to enable initial RTS/CTS hardware flow control
in the dts.
Co-authored-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
The SYSCFG_CFGR1_PA11_PA12_RMP define is present even on packages where
the remap isn't strictly required. This commit makes the remap optional
based on a DT property.
Also fixes syntax error caused by a missing );.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
On STM32F3 devices, a trick was required for normal use of registers.
This was actually an issue in flash registers defintions which should
be defined as volatile.
Fix this and additionaly, fix definition for STM32F1 which was also
lacking the volatile instruction.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32f4 series, uart4 is not an usart, so generated with
'st,stm32-usart' compatible and hence generated defined should be
prefixed with DT_ST_STM32_UART_ rather than DT_ST_STM32_USART.
Fixes#14542
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There are some implicit rules in STM32 family Kconfig.defconfig
fragments organizations.
Add comments to explicit these rules.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
GPIO port H is available on all SoCs of L4 series.
Move Kconfig GPIO_STM32_PORTH symbol deifnition to series Kconfig
fragment Kconfig.defconfig.series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Follow the pattern we have for other peripherals in that if the driver
class (CAN) is enabled than enable the driver for that class
(CAN_STM32). Also have the STM32 CAN driver depend on being on a STM32
SoC.
Remove setting of CONFIG_CAN_STM32 in any .conf files as it will get set
of CONFIG_CAN is set/enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit removes "select SYS_POWER_*_SUPPORTED" entries from
Kconfig on SoCs which are not implementing sys_set_power_state()
method used to control power mode.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
A common driver is shared between stm32 chips, which was not the case
for stm32f3 series. As a consequence stm32f3 was not maintained
equally and was missing features such as flash layout or dts based
configuration.
Besides, drivers had some flows such as wrong bus clock and
missing HSI clock activation which lead to issues on boards not
using HSI as main clock.
As a consequence this commit moves stm32f3 series flash driver to
common stm32 flash drivers.
Fixes#4197
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The SYS_POWER_LOW_POWER_STATE_SUPPORTED and SYS_POWER_LOW_POWER_STATE
suggests one low power state but these options control multiple
low power state. This commit uses plural in the names to indicate
that.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
SoC family STM32F769XI supports both double and single precision
floating-point unit. This commit enables double-precision by
default in this SoC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Provides a STM32 RTC driver using new counter API.
Driver does not support wrap related functions (set, get, ..)
Fixes#11373
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
exti driver implementation does not fit all SoCs because
some EXTI ip does not match stm32_exti register map provided.
Instead of providing exti register map for all SoCs, use LL API
which abstracts IP variations and enable uniform use of the drivers
on all STM32SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds STM32 L452 soc with L452xC variant. L452 has 160 KB SRAM;
therefore, mpu mem config has been extended; IRQ number is based on
'stm32l452xx.h'.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Clean up a left over from GPIO driver factorization.
Definition of GPIO_REG_SIZE and GPIO_PORTS_BASE do not need anymore
to be spread accross SoCs.
Put these definitions directly in STM32 pinmux driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The original implementation of gpio functions access registers
directly. Using LL library can add a set of unifying access
functions for all series of stm32 for avoiding accessing low level
code, and improve readability.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
All series STM32 have mostly the same GPIO architecture
and can share the same code for GPIO manipulation.
Functions of the external interrupt line control are also the same.
This patch extracts common code from them and put them into the 'common'
folder.
Functions of control GPIO of these series scattered in
soc/arm/st_stm32/stm32xx/ folders contain these functions:
stm32_gpio_flags_to_conf(), stm32_gpio_configure(), stm32_gpio_set(),
stm32_gpio_get, stm32_gpio_enable_int().
This patch merges them into the gpio_stm32.c file.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
On STM32L4, 14 pins (Port G[15:2]), require external power supply.
Activate this at port G init when PWR_CR2_IOSV is defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add uart5 nodes to stm32f1 series dts.
Provide matching dts_fixup add-on.
Signed-off-by: Chen Han <qq1433255094@outlook.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support for Low Speed External 32.768 kHz oscillator (LSE ).
Add support for MSI PLL-Mode offering an automatic calibration feature
in combination with the LSE. This allows the MSI to reach an accurate
+/-0,25% clock perfectly suitable for USB full-speed clock.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
This patch adds a flash driver for the STM32F7x series, inspired from
the STM32F4x one. It has been tested on the STM32F723, but should also
work on other SoCs of the family.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Declare and define arm_mpu_config and arm_mpu_regions
structs as const, as they are not modified in run-time.
Fixes#10320
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds support for STM32L471xG. Since STM32L475 only adds
USB, stm32l475.dtsi now includes stm32l471.dtsi
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
All drivers require DTS for their primary SPI settings.
Removing SPI_[0-9]_NAME config option added some more samples changes.
Usage of these options there was anyway not relevant.
Fixes#11064
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Now that Cortex-M7 cache issues have been fixed in commits 828ae6b8 and
13972693, it is possible to safely enable the MPU on the STM32F7 SoC
series.
Note that the ITCM area is not mapped into an MPU region. This should
not be an issue for now, as Zephyr does not provide yet a way to
populate and use this area.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
STM32F103 micros starting from 64-pin (xE) packages upward have
available port G. This patch defines a dts binding for them.
Signed-off-by: Pavel Kral <pavel.kral@omsquare.com>
Provide CONFIG macros for clocks bits and bus properties in fixup
files and use them to simplify logic in uart devices instanciation
code
Fixes#10448
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The information extracted from the device tree is now used to initialize
GPIO device instances. Up until now the GPIO device driver made no use
of this information. Actual instance creation is still controlled using
the Kconfig method. Missing GPIO device tree nodes were added in the
process for STM32L073, STM32F413 and STM32F373.
The information for gpio instance initialization has already been
present for supported STM32 SoCs but remained unused. Changes in the
device tree had no effect on GPIO functionality and was essentially
redundant. Using the device tree for hardware description seems
plausible and less painful than a myriad of defines in some SoC
description header.
The change was implemented under the assumption that current device
trees provide a correct description of the SoCs. Base register addresses
and RCC register bits were not explicitly checked for each device.
Manual tests were executed on:
- NUCLEO-F103RB
- STM32F429I-DISCO
- STM32F746G-DISCO
- NUCLEO-F767ZI
Manual tests consisted of blinky on different GPIOs and pins on each
board.
sanitycheck was executed for all STM32 based boards
Fixes: #10629
Signed-off-by: Martin Bertsche <martin72216@googlemail.com>
The only difference between the F413xH and F413xG is flash memory size.
STMF413xH: 1536 Kbytes
STMF413xG: 1024 Kbytes
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
For the stm32f4xx family the SPI and I2S are sharing same
controller, so we can reuse same definitions.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
stm32f4xx_ll_spi.h include file is shared between I2S and SPI
(controller is same). So we need to include it even when I2S_STM32
is enabled.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This patch adds timers and PWM nodes to STM32 F7 series, as well as the
corresponding dts fixup entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit introduces CPU_HAS_ARM_MPU and CPU_HAS_NXP_MPU options,
which indicate which flavour of MPU is supported by given SoC family.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The STM32_ARM_MPU_ENABLE option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the STM32_ARM_MPU_ENABLE option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
