In case of dualcore, STM32H7, STM32W and STM32MP1,
protect concurrent register write access with HSEM.
Done for following drivers:
clock_control, counter, flash, gpio, interrupt_controller
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This patch introduces the support of low power modes
for the STM32WBxx from STMicroelectronics based on the lptim
Here, the power modes are sleep modes have lptimer as wakeup source.
The sleep modes are configured by the SYS_POWER_MANAGEMENT.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Only boards with at least 64K Flash will activate MPU because:
MPU + UERSPACE + All switches implicity activated
(CONFIG_MPU_STACK_GUARD, CONFIG_ARM_STACK_PROTECTION ...)
will consume about 40K Flash
(value computed on nucleo_f767_zi on tests/arch/arm/arm_ramfunc/).
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The PWM drivers has been refactored using the HAL LL API. Not only that,
but the set pin_set function is now faster, as channel output compare is
just initialized if needed.
NOTE: Has been tested using H743zi board for now.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Those MCUs have 2KB RAM and 16KB FLASH memory, but they are still
powerful enough to run small configuration of Zephyr RTOS.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Added / Tested support for RNG on the STM32F767ZI nucleo board.
Updated the SoC defconfig to auto-enable the driver when
ENTROPY_GENERATOR is enabled, and updated the board README.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
This patch introduces the support of low power modes
for the STM32L4xx from STMicroelectronics based on the lptim
Here, the power modes are sleep modes with lptimer as wakeup.
Depending on the SYS_POWER_MANAGEMENT configuration.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the necessary clock configuration to support STM32L-based
SoCs. This change likely adds support for other STM32 SoCs as well
since the HSI48 clock is configured for all SoCs that support it
(except the STM32L4x) instead of just the STM32G4X.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
This is defining the SYS_CLOCK_TICKS_PER_SEC default value
depending on the LPTIM CLOCK frequency in case of LPTIMER,
to get a TICK value as a divider of the LPTIM clock source.
It gives a better result in formulas when converting
ticks to count unit.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Changes:
- Added all required board files in /boards/arm/96b_aerocore2
- Modified pinmux for stm32f4
Most of the changes in this PR is based on reverse-engineering of the
PCB layout and following commits in the PX4 firmware repository for
the same board. The manufacturer does not provide and or generate
schematics and pinout tables for this board.
This PR includes almost all of the interfaces connected to the STM32
MCU, the only thing not included is the J9 and J8 headers that connect
to a 96Boards baseboard.
These headers are not vital to the functionality of the Aerocore2.
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Add STM32F427. This is mainly aimed towards the stm32f427vi.
Changes:
- Add stm32f427 support based on previous work
done for the stm32f429.
- Rework currunt stm32f429 implimentation to now
be based on stm32f427.
- Introduce dedicated dtsi for the VI variant of both
stm32f427 and stm32f429. This is done to prevent stm32f4.dtsi
from being included twice.
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Use MSI as PLL source. This enables to run system clock at 110MHz.
To achieve this, voltage regulator should be set to scale 0.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch defines the dma feature for the stm32wbXX
and the dmamux feature for the stm32wb55x
soc series from STMicroelectronics
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add support for ADC on H7 series. Note that ADC1 and ADC2 share the same
register set, so it is added as "adc1_2".
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Due to a typo compiling the WWDG on the g4 family does not
work. This adds the correct include filename.
Signed-off-by: Richard Osterloh <richard.osterloh@gmail.com>
Enable I2S_STM32 in the soc common part, so it will no
longer be required in board default configuration.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Remove DT_ADC_{0..2}_NAME from dts_fixup.h, if this casues the
dts_fixup.h file to be empty we remove the file as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Complete STM32 conversion to new DT macros by removing
remaining occurences of DT_ST_STM32_ADC_FOO_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Complete STM32 conversion to new DT macros by removing
remaining occurences of DT_ST_STM32_ADC_FOO_LABEL.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The DT_I2S_* defines can be removed as the driver is now utilizing the
new dt macros that don't require these defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We don't need to define DT_NUM_IRQ_PRIO_BITS or DT_NUM_MPU_REGIONS in
dts_fixup.h files anymore, so we can remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make use of DT_NODELABEL macros to get device instances
information to configure drivers I2C instances.
This allows to remove I2C related lines in fixup.h files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use compatible information to configure i2c stm32.
With this, driver version selection is done thanks to compatible
and it is not needed anymore to do this via Kconfig symbol
selection under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
