This patch introduces the support of the Low Power Timer
for the STM32WBxx from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The SPI NOR driver requires that the size (in bits) be provided in the
devicetree node. Update the binding to make the property required,
and update all nodes based on the memory chip identified.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This patch introduces the support of the Low Power Timer
for the STM32L4xx from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds supoprt for the Atmel SAME54 SoC.
The SAME5x/SAMD5x is a line of Cortex-M4F MCUs that share peripherals
with the sam0 Cortex-M0+ and saml1x Cortex-M23 parts.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Introduce a standard watchdog alias 'watchdog0' that can be utilized
by sample/test code in the future. This helps remove the need for
CONFIG_WDT_0_NAME in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit moves DMA parameters previously hard coded in the driver
to the dts.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There is no APB2 bus on stm32f0 series.
What could be found as APB2 in CMSIS files is actually
second group of APB (A.K.A APB1_2).
Fix nodes that are using this wrong reference accorss the series.
Fixes#20310
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move the selection of the IP clock source for the modules in the NXP
Kinetis KE1xF SoCs from being hardcoded in soc.c to being specified in
the device tree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
STM32L151XB-A SoC is almost similar to the STM32L151XB SoC except that
it has more RAM (32KiB). Hence add devicetree and Kconfig support.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Indtroduction of generic device tree bindings for keyboard scan devices.
In addition, device tree node entries and dt specific bindings where
also implemented for Microchip MEC1501
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
STM32L1 uses the same spi controller as STM32F1 so we can just set the
right addresses and enable them. We also need to add the fixup names and
to correctly include the header for ST LL HAL.
Signed-off-by: Karl Palsson <karlp@etactica.com>
1. Replace the non-existent CPU device binding ("Cortex-R") specified
by the CPU node with a proper one.
2. Relocate CPU node declaration to SoC dtsi:
The CPU node should be declared in the SoC dtsi because the core
type is SoC-dependent. In fact, this is exactly how it is done in
the Cortex-M port.
3. Remove core_intc (supposedly Cortex-R VIC):
Unlike the NVIC of Cortex-M, the VIC of Cortex-R is not a true
interrupt controller in the conventional sense and merely acts as
a CPU input port for aggregated interrupt request and vector index
signals. For this reason, there is no point in declaring it in the
device tree and specifying it as an interrupt parent. All SoCs
incorporating Cortex-R implement a separate true interrupt
controller (for instance, GIC for Zynq MPSoC and VIM for Hercules).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The patch adds initial support for STM32F030X4 SoC.
STM32F0 Cube package advises to use 'stm32f030x6' code
for both STM32F030x4 and STM32F030x6 SoC variants.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Add soc and dts files to support for most of the common peripherals
in the STM32G4 series. Add specific support for the STM32G431RB.
Signed-off-by: Richard Osterloh <richard.osterloh@gmail.com>
Add #pwm-cells property in bindings for Nordic PWMs and add this
property with a suitable value assigned to all PWM nodes in dts
files for Nordic SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for DTS nodes
representing different types of Nordic SPI peripherals. Previously
"nordic,nrf-spi" was used for both SPI and SPIM. SPIS was already
handled separately.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/spi/
new binding for "nordic,nrf-spim" is added and common fields for all
3 types of Nordic SPI peripherals are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in spiX nodes are updated (when there is no
choice as only one type of SPI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/spi/
spi_nrfx_spim driver is updated with the new form of macros generated
from dts
* boards/
all spiX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of SPI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (SPI_x_NRF_SPI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the device tree to assign the correct peripheral clock to each
UART/USART/LEUART. Previously, the clock identifier was determined
through the sequence number of the instantiated UART. This meant
configuring all UARTs when only one of the later UARTs was required.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
This adds support for Kinestis K22
Co-authored-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Co-authored-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Co-authored-by: Tom Burdick <thomas.burdick@gmail.com>
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
Add RTC timer driver for CC13X2/CC26X2, and use it instead of systick
as system clock. It is necessary to use this timer for power
management support, so that the system can exit from deep sleep upon
expiry of timeouts.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
4 are found: 2 with a counter of 16bits and 2 with a counter of 32 bits.
However, first 32bits instance will not be exposed as it will be used by
rtos timer driver directly to implement k_busy_wait()
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32wb SoC. Enable the independent watchdog
for the stm32wb series for use with this driver.
Signed-off-by: Robert Weber <robertweber95@gmail.com>
The KE1xF SoC family SIM unit differs from the other Kinetis family
SoCs. Add a unique compatiable and binding for it.
Fixes#18160
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For quite a few peripherals that are currently supported by nrfx HALs
or drivers there are no definitions of corresponding CMSIS-Core
peripheral accessing symbols that would provide their base addresses
in the proper domain (secure or non-secure), accordingly to the build
target. This commits adds devicetree nodes for these peripherals so
that their base addresses can be used in definitions of the accessing
symbols mentioned above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Pull out the LPO fixed-clock that is part of the PMC hardware block as
its own child node of the PMC block. This is because the PMC could have
its own driver associated with it that is seperate from the LPO clk.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the ADC bindings to include #io-channel-cells and update the
related dts files to set #io-channel-cells.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
'interrupt-parent' should contain just the phandle of the node
interrupts are sent to.
This node (gic: interrupt-controller@f9010000) doesn't generate any
interrupts, so the 'interrupt-parent' value is never used (this is why
it wasn't caught). It'll give an error later with 'interrupt-parent'
declared as 'type: phandle' in bindings though.
Don't know what was intended. Just remove the 0.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
SPI3 clock info were missing and following macros were
not generated:
- DT_ST_STM32_SPI_FIFO_40003C00_CLOCK_BITS
- DT_ST_STM32_SPI_FIFO_40003C00_CLOCK_BUS
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds support for the Zynq UltraScale+ MPSoC as a qemu based
platform for Cortex-R based testing. This SoC only supports an
interrupt controller and serial port for limited testing.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
Remove unused "system-clock-frequency" property, we don't have this
defined in various bindings and thus aren't using it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use clock specified in the device tree for obtaining the source clock
frequency for the pwm_mcux_ftm driver instead of relying on having an
NXP Kinetis MCG clock available in all SoCs supporting FlexTimer (FTM)
modules.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
NRF_UICR needs to be defined for nRF9160 SoC in
nrfx_config_nrf9160.h, because it is not defined
in nrfx/hal/mdk/nrf9160.h (as it is a Secure-only
peripheral).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
With the new DT checks the dts bindings for "nxp,flexpwm" and
"nxp,imx-pwm" had old conventions that we now treat as build errors.
Additionally fix the number of #pwm-cells for "nxp,imx-pwm" to be 1.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
i.MX RT10XX processors have four eFlexPWM modules, each containing
four 2-channels PWM submodules.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The true mmio-sram nodes should not have had a 'device_type' property.
Remove it from the cases that we clearly know are SRAM.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These are not declared in dts/bindings/arm/nxp,kinetis-sim.yaml and do
not generate any output.
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
A minor spelling fix in an inline comment in
both nRF9160 Secure and Non-Secure .dtsi headers.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
These are not declared in any binding and do not generate any output.
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fix the following dtc warning:
mimxrt1064_evk.dts.pre.tmp:78.31-85.5: Warning (spi_bus_bridge):
/soc/flexspi1@402a4000: node name for SPI buses should be 'spi'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Several aliases were added to nrf9160[ns].dtsi files solely for
the purpose of getting base addresses of certain hardware modules
via DT_ macros generated for these aliases.
Since for one-instance modules the same can be now achieved with
standard DT_INST_0_* macros, there is no need to keep these aliases.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
pinmux: Add the relevant definition of the spi3 pin
dts: Fix a bug, spi3 does not have a label
soc: Supplement spi3 related definition
Signed-off-by: Findlay Feng <i@fengch.me>
stm32f429.dtsi wrongly introduced i2s nodes 4, 5 and 6.
Remove them as actually only i2s nodes 2 and 3 are supported on
these socs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a kernel timer driver for the MEC1501 32KHz RTOS timer.
This timer is a count down 32-bit counter clocked at a fixed
32768 Hz. It features one-shot, auto-reload, and halt count down
while the Cortex-M is halted by JTAG/SWD. This driver is based
on the new Intel local APIC driver. The driver was tuned for
accuracy at small sleep values. Added a work-around for RTOS
timer restart issue. RTOS timer driver requires board ticks per
second to be 32768 if tickless operation is configured.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This was always intended to be a bytestring rather than an array, but
full support was missing. Since that has been addressed switch it to
the preferred format.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The property is required on all SPI clients, but was missing from
several devicetree nodes. Set it, using the capitalized version of the
node alias when present, with "jedec,spi-nor#0" as the fallback.
Closes#17662
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Have the SoC dtsi files for microchip mark the devices (uart & i2c) as
disabled by default and let the board dts files enable which one's they
need/use (which is what's happening already).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
spi-max-frequency is marked as required in
dts/bindings/mtd/jedec,spi-nor.yaml.
I took the value from the datasheets (133 MHz for all), and guessed that
a dummy entry is fine for QEMU.
Fixes some errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There doesn't seem to be any use of the virtualcom device in the code,
so lets remove it from the dts as it describes itself as a usb device
controller which it is not.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds a fixed clock node (representing clock driving
system bus). The added node is then referenced by peripherals requiring
information about driving clock frequency.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
This commit adds 'clock-frequency' property to the cpu nodes.
The clock frequency specified in the added property is used
during platform configuration. Examples:
- The SWO logger uses clock frequency to configure SWO output.
- Plenty of platforms need CPU clock specified for their HAL.
- Most of devices with USB needs information about CPU clock
in order to configure USB clock source.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
This patch populates "clocks" property in stm32 usb nodes
for clock related usb configuration code of each dtsi files
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The spi-nor flash nodes require a jedec-id property as per the binding.
We add the jedec-id's as best we can determine based on the data sheets
for the various flash modules on these boards.
However these id's should be validated by actually reading the value to
ensure they are correct.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix USB phy node for stm32l432 and stm32l452, which contain
a USB controller and not a OTG FS controller.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
1) dts/bindings/mmc/mmc.yaml: specifies common mmc.
2) dts/bindings/mmc/nxp,imx-usdhc.yaml: specifies
nxp usdhc module which inherits mmc.
3) dts/arm/nxp/nxp_rt.dtsi: usdhc support on RT chip.
4) boards/arm/mimxrt1050_evk/mimxrt1050_evk.dts:
usdhc slot support on mimxrt1050_evk board.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
A number of minor issues with the 'fixed-clock' support:
* Fix the #clock-cells to be 0
* Fix nxp_ke1xf.dtsi to set #clock-cells 0 and the clock reference to
only be a phandle.
* Fix the generation script to only generate what it should for a
'fixed-clock'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add clock support for STM32G0X SoC series.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch adds support for the STM32G071xx
from STMicroelectronics.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com>
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Allow individual specification of the time quanta used for the CAN bus
propagation segment and phase segment 1.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Added support for the STM32L496XE series with 512KB internal flash and
256KB SRAM of contiguous addresses.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
sram2a and sram2b where defined in the prospect of defining
HCI shared memory sections from device tree.
Remove them, since this is not the case anymore.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add support for the Low Power Inter-Integrated Circuit (LPI2C)
controllers found in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The node name for device_id was device_id@0 it should be
device_id@80a00c to reflect the first register region
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ARM SysTick peripheral is optional in Cortex-M0 MCUs,
so we delete the respective dts node when the peripheral
is not present.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Atmel SAM D series SoC variants (present in the tree) all have
an ARM Cortex-M0+ core, not a Cortex-M0, so we correct this in
the .dtsi header.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Unlike Cortex-M3 and Cortex-M4, in Cortex-M7 the number of
MPU regions may vary based on the implementation. This commit
adds a DTS node for the ARM MPU peripheral in the device tree
of Cortex-M7 SoCs and updates the fixup files, so we may extract
the number of MPU regions at build time. SoCs:
- nxp_rt
- same70
- stm32f7
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Adding missing erase-block-size entries for the flash-controller
nodes in the nrf52810 and nrf52811 .dtsi files.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move flash-controller and SRAM node definitions under SoC node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Reduced Kconfig for counter with nRF TIMER and RTC. Added overlays
for TIMER and RTC configuration in the counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds basic support for nrf52811 in the arch SoC, dts
and nrfx folders.
The nRF52811 is a Bluetooth 5.1 Direction Finding SoC with comprehensive
protocol support.
The nRF52811 SoC is capable of the latest features of Bluetooth 5.1,
the most prominent being Direction Finding.
The radio in the nRF52811 SoC has comprehensive protocol capabilities,
including Bluetooth 5.1 Directing Finding, all Bluetooth 5 features,
802.15.4, Thread, Zigbee, ANT and 2.4 GHz proprietary.
It has 4 dBm TX power and has been optimized to offer the best RX
sensitivity of all SoCs in the nRF52 series.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
add usbd1 definition to rt dts file,
set EHCI controller config default value in rt1050 default config file,
add EHCI controller driver MACROs to dts_fixup.h,
initialize EHCI clock in rt soc.c
add HAS_MCUX_USB_EHCI for supported soc in Kconfig.soc
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Dts Nodes for all the GPIO portswere defined. In addition,
a new binding file was created for the gpio driver.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Expose MEC1501 5 I2C/SMB controllers
Add Microchip specific I2C device tree properties
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
All series of stm32 have at least one ADC instance and this commit adds
one ADC node to the root dts file of each soc, and also adds fixing up
mappings to them.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
This adds interrupt support to the SAM0 GPIO driver. This is heavily
inspired by @nzmichaelh work in #5715. The primary difference
from that implementation is that here the External Interrupt
Controller (EIC) is separated out into an interrupt controller driver
that is less tightly coupled to the GPIO API. Instead it implements
more of a conversion from the EIC's own odd multiplexing to a more
traditional port and pin mask IRQ-like callback. Unfortunately,
through the EIC on the SAMD2x are relatively well behaved
in terms of pin to EIC line mappings, other chips that share the
peripheral interface are not. So the EIC driver implements a
per-line lookup to the pin and port pair using definitions extracted
from the ASF headers.
The EIC driver still makes some assumptions about how it will be used:
mostly it assumes exactly one callback per port. This should be fine
as the only intended user is the GPIO driver itself.
This has been tested with some simple programs and with
tests/drivers/gpio/gpio_basic_api on a SAMD21 breakout and an
adafruit_trinket_m0 board.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds a SERCOM I2C driver for SAM0 series chips.
Tested with a SAMD21 chip on a SSD1306 display and a MLX90393
sensor. Only compile tested for SAMD20 and SAMR21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Implementation of pinmux for the stm32mp157c_dk2 board.
Some UART pin mux definition has been added (mainly for
UART console and UART/SPI Arduino shield support).
This can be completed with pin mux for other stm32mp157c
UART.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for stm32mp1 basic UART API with Zephyr.
UART Console and UART shell are also supported.
Async UART API and USART support is to be done.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move SERCOM peripherals to use the raw defines generated from DTS
parsing. This adds aliases to the DTS so that the SERCOM number
can still be used for clocking and pinmux.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the SAM0 DMA Controller (DMAC). Chained
transfer are not currently implemented.
Tested with tests/drivers/dma/loop_transfer and custom modifications
to that test using three parallel reloading channels. Also tested
with a trivial program that did memory->serial.
Signed-off-by: Michael Hope <mlhx@google.com>
[hageman@inthat.cloud: Rebased and updated commit message]
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Initial support for Microchip MEC1501 series is added to the tree.
Additional support for UART is also included. This SoC supports
two operational modes for interrupts (Direct and Aggregated). For
this commit, the direct capable interrupts are configured in
direct mode.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Adds Atmel SAMR21 soc which is based on SAMD21, but with a AT86RF233
radio connected internally via SPI.
The AT86RF233 is not yet supprted by Zephyr at this point.
This code is very much copy & paste from atmel_sam0/samd21
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Add USART1 and LPUART1 nodes on stm32wb series.
Only these 2 ones are available for now on this series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add GPIO support to stm32wb series.
Only ABCDE and H ports are available for now on this series.
Accordingly, update series dtsi file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support to stm32wb series in stm32 clock_control driver.
Ip is similar to stm32l4 one but AHB bus presacler is renamed
to "CPU1" and CPU2 and AHB4 prescalers should be defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add driver support for Atmel SAM0 device ID, which is 16-bytes long.
The device ID can simply be read from memory at a known location, but
the location is only described in the data sheet, not in ASF.
For SAMD2x it's 0x0080A00C, 0x0080A040, 0x0080A044 & 0x0080A048.
For SAMD5x it's 0x008061FC, 0x00806010, 0x00806014 & 0x00806018.
This adds a new property to the device tree to define the device ID
registers for this SoC family.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
2 identical packages were defined for stm32f412 SoC, invariant "g".
Merge them in new sinclge stm32f412Xg.dtsi.
Update matching boards accordinlgy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
SAMD20 does not have the DMA or USB peripherals and as a result
the IRQs for all subsequent lines are shifted down from SAMD21.
This splits the interrupt assignment for the SERCOMs into the
SoC specific DTS file and moves the USB definition to SAMD21 only.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Ports B and C share a common interrupt vector on kw40 and kw41z socs,
but we don't currently have a way to express this in device tree. A
check was added in commit 77cb942a97 that
correctly causes build errors on kw40/41 boards when both ports are
enabled.
Disable the port b interrupt for now until we have a better way to
handle this.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
According to nrf51 and nrf52 specifaction every peripheral is
assigned a fixed block of 0x1000 bytes. Due to that dts for
nrf51 and nrf52 chips have been updated.
The only exception is gpio for nrf52840 where gpio0 and gpio1
share the same memory regions. For this reason, the definition
of gpio for nrf52840 is different from the others.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
On various stm32 soc packages CCM is available and SRAM size
mentionned in datasheet include CCM.
Though, actual SRAM size defined in dtsi files should not
include CCM sizes.
Fix this on impacted dtsi files.
Fixes#14779
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The iMX RT1060 and RT1064 have additional dedicated 512KB on-chip ram.
This OCRAM2 is mapped at 0x20200000, formerly OCRAM1 (flexram) mapping
which is moved to 0x20280000 in order to guarentee global OCRAM memory
continuity regardless OCRAM1 size configuration (256KB by default).
In default configuration, this gives 768KB (512+256) on-chip ram:
0x20200000 to 0x202BFFFF.
OCRAM2: 0x20200000 - 0x2027FFFF
OCRAM1(FlexRam): 0x2028FFFF - 0x202BFFFF
Add this memory region as a single node in the rt1060 device tree.
Note: MPU expects power of two memory region, in case of 768KB, let
the MPU configure 1MB instead.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
uart4 is not available on whole stm32f4 series (not on stm32f401
for instance), remove from stm32f4.dtsi
It is actually correctly defined in f405, f413 but missing in f446,
so add it in there.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
1. SW PWM device node added to common nrf5_common.dtsi
2. SW PWM node set in all nRF5x DTSI files.
Different initial settings for nRF51 and nRF52 devices.
Status is ok by default for nRF51.
3. Added yaml binding for Nordic SW PWM node.
4. Set codeowner of nordic dts bindings to @anangl
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
In the recent MDK brought by nrfx 1.6.2, these legacy peripherals have
been revealed as available also in nRF52810. This patch allows their
use in Zephyr drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
On currently supported stm32f3 chips,
erase-block-size = 2048
write-block-size = 2
Set these property in stm32f3 series root dtsi file.
Fixes#9686
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add nvs support to nucleo_f091rc board. This requires to
add erase-block-size property to stm32f0.dtsi.
Storage partition is set to 4kb at the end of the flash.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Initial support for Microchip MEC1701 series is incorporated to the
tree. Additional support for UART is also included. This SOC supports
two operation modes for interrupts (Direct and Aggregated). For this
commit, the interrupts are configured in direct mode.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This patch adds basic support for the PWM devices available on the Atmel
SAM family. Beside enabling the driver, everything is selected through
the device tree, including enabling the PWM0 and PWM1 devices. Thus
CONFIG_PWM_0 and CONFIG_PWM_1 are ignored.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add EPIT (Enhanced Periodic Interrupt Timer) peripheral support
for i.MX6SoloX soc.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Adds device tree bindings for the imx enhanced LCD interface (eLCDIF)
controller. The compatible is reused from linux.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Actually, add the "status" property that enables the nodes explicitly.
They were apparently enabled by default without this property.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add sam0_rtc_driver that implements system timer API on top of the RTC
and can be used as a replacement for the default systick timer.
Signed-off-by: Martin Benda <martin.benda@omsquare.com>
This commit introduces the possibility to have multiple
device nodes attached to the same I2S controller. For this
purpose a new i2s-device.yaml description has been introduced
with the a 'reg' property to define the logic number of the
device. For example, if two microphones are attached to the
same I2S port (say 1) to achieve stereo audio, the two microphones
might be described in dts as:
&i2s1 {
status = "ok";
mic@0 {
compatible = "...";
reg = <0>;
label = "...";
};
mic@1 {
compatible = "...";
reg = <1>;
label = "...";
};
};
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added UART4 alternate pin function for L4 µC for PC10 and PC11.
Corrected naming of previously defined UART4 TX and RX defines.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
The SPI1 controller that is connected to the mcr20a block utilizes the
hardware chipselect and not a GPIO CS. So remove the cs-gpios property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SPI0 node had a property called 'cs' which wasn't used or defined as
part of the binding yaml. So let's remove it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get warnings from dtc when building any of the NXP i.MX-RT boards of
the form:
mimxrt1020_evk.dts_compiled: Warning (simple_bus_reg):
/soc/random@400CC000: simple-bus unit address format
error, expected "400cc000"
Simple fix to make everything lowercase to have the unit-address and reg
match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds STM32 L452 soc with L452xC variant. L452 has 160 KB SRAM;
therefore, mpu mem config has been extended; IRQ number is based on
'stm32l452xx.h'.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Use the symbol generated from DT so that it is common for nRF9160
and nRF5 family SoCs. To avoid artificial renaming of CLOCK_POWER_IRQn
to POWER_CLOCK_IRQn.
For nRF5 family SoCs clock nodes were not defined so far, thus they are
added so that the proper DT symbol is generated for them as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add missing node for instance 0 of the RTC peripheral and use an alias
to the flash-controller node instead of the nvmc node definition (there
is no need to have a separate node just to get the NVMC base address).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fix the QSPI and hyperflash nodes to be proper SPI children and expose
the address range for direct access as part of the controller's reg
region.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the TRNG device contained in the i.MX RT SoCs. It uses
the existing MCUX driver, and mostly consists in adding the Kconfig and
DTS entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add uart5 nodes to stm32f1 series dts.
Provide matching dts_fixup add-on.
Signed-off-by: Chen Han <qq1433255094@outlook.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit introduces the main device tree header files (.dtsi)
for Nordic nRF9160 SOC, for both Secure and Non-Secure domains.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We only need to add the reg property in flash0 and sram0,
in the different DTS headers for the nRF SOCS. We do not
seem to need to define the nodes again. This commit applies
this simplification for flash and sram sizes definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Fix the following warning that shows up in some NRF device tree files:
Warning (simple_bus_reg): /soc/pwm@4002D000: simple-bus unit
address format error, expected "4002d000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On i.mx6/7 the TCMU and TCML regions are specific to instruction or
data. So use the nxp,imx-itcm for TCML and nxp,imx-dtcm for TCMU.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The imx-rt-{i,d}tcm bindings can actually be utilized on the i.MX6/7 as
well for the TCM{L,U} regions of memory as they are specific to
instruction or data.
So let's rename imx-rt-{i,d}tcm to imx-{i,d}tcm.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Due to a bad timing in merging PR #10744 and PR #12083, the flash0 node
in stm32f756Xg.dtsi ended-up at the root of the device tree, while the
flash0 node it is trying to override in stm32f7.dtsi is now under
/soc/flash-controller.
This patch fixes that by moving it at the right location.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Adds a second sram node to the k64 device tree to acknowledge that the
additional sram is present in hardware, but deliberately not used in
zephyr until an outstanding issue is solved. The upper and lower sram
nodes are contiguous in the memory map, however the Cortex-M4
architecture does not support misaligned accesses across the boundary
between the two nodes.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds a flash driver for the STM32F7x series, inspired from
the STM32F4x one. It has been tested on the STM32F723, but should also
work on other SoCs of the family.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We currently get a number of warnings like:
Warning (simple_bus_reg): /soc/otgfs_phy: missing or empty
reg/ranges property
This is due to the usb phy nodes not have a reg property since they
don't have an mmio address associated with them.
Move the phy nodes out of the SoC node so their lack of a reg property
will not cause a warning. This is similar to how Linux dts files
handle the phy nodes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the following warning that shows up in some NRF device tree files:
Warning (simple_bus_reg): /soc/pwm@4001C000: simple-bus unit
address format error, expected "4001c000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
1. PWM device node added with alias to all
nRF52x DTSI files. 1 instance for
nRF52810, 3 instances for nRF52832, and
4 instance for nRF52840.
2. Added yaml binding for Nordic PWM node.
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
Add comptiable into the device tree and associated binding files for NXP
i.MX RT ITCM/DTCM memory regions.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The STM32L433 has the same layout than the STM32L432, additionally it
has GPIOD, GPIOE, I2C2, USART3 and SPI2.
Also move USART3 and SPI2 out of stm32l4.dtsi since STM32L432 does not
have it.
Fixes#10909.
Signed-off-by: Markus Roppelt <markus.roppelt@gmx.de>
The Silicon Labs EFM32 Pearl Gecko MCU includes:
* Cortex-M4F core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* multiple low power peripherals
Ported from EFM32WG:
https://www.silabs.com/documents/public/application-notes/an0918.0-efm32_to_efm32jgpg_migration_guide.pdf
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds the virtualcom device to the nrf52840 SoC dts and adds a board
specific nrf52840_overlay.dts file, copied exactly from the
arduino101_overlay.dts file, to set the console device name
appropriately for the subsys/usb/console sample project.
There were no clear alternatives to add a usb_cdc: virtualcom device to
all known SoC devices with USB support as should probably happen.
There was also no clear alternatives to add a non-board specific overlay
to the example.
This fixes a specific problem with the nrf52840-dk board for this sample
project.
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
This commit adds support for STM32L471xG. Since STM32L475 only adds
USB, stm32l475.dtsi now includes stm32l471.dtsi
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
This patch adds a flash driver for the Atmel SAM E70 SoC. The driver has
been kept simple by considering that the flash is only composed of 8-KiB
blocks. Indeed an area at the beginning of the flash might be erased
with a smaller granularity, and the other blocks can also be erased with
a higher granularity. It also only handles the global read/write
protection, not the 128-KiB lock regions. A write error is returned if
a region is locked.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables Networking hardware on i.MX-RT type drivers.
Reuses the same eth_mcux driver used by Kinetis family; initialization
sequence refactored to work with this board as well. Unlike Kinetis
family, i.MX has a single ENET interrupt and we need to discriminate
between interrupts using a status register.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add Messaging Unit B peripheral support for i.MX6SoloX soc so it can
use IMX IPM.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
dtc was producing this warning when we build on SAMD SoCs:
Warning (simple_bus_reg): /soc/nvmctrl@41004000:
simple-bus unit address format error, expected "40022000"
The reg addr isn't used by the flash_sam0.c driver so we wouldn't notice
this issue. Looking at the atmel HAL we see:
#define NVMCTRL ((Nvmctrl *)0x41004000UL)
So that provides confirmation of what the reg addr should be.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
