This commits adds GPIO driver for LiteX SoC builder.
Due to the fact that GPIO in LiteX is unidirectional and can be
configured with different pins amount per port, additional entries
were added to the dts file.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
PCA95XX is a series of compatible I2C-based GPIO expanders,
with common registers on input/output, polarity and configuration.
This renames the original PCAL9535A driver to PCA95XX to indicate
that it can support this series. Additional features on variants
are guarded by kconfigs.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add driver for the Texas Instruments LMP90xxx series of multi-channel,
low-power 16-/24-bit sensor analog frontends (AFEs).
The functionality is split into two drivers; an ADC driver and a GPIO
driver.
Tested with LMP90080 and LMP90100.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The gpio_atmel_sam3 is no longer required since the gpio_sam, common
SAM family GPIO driver, provides improved functionality.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Adds a new xec gpio driver that can be used with the
XEC MCUs. This driver modifies the PCR1 register in order
to configure gpio settings. Interrupts are triggered by the EC
interrupt aggregator block.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit adds support for the keyscan functionality of the HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board is unmaintained and unsupported. It is not known to work and
has lots of conditional code across the tree that makes code
unmaintainable.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
* Add support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
Provide basic commands for configuring/setting/reading GPIO ports.
> gpio conf ..
> gpio set ..
> gpio get ..
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
After GPIO shim using NRFX has been implemented, old gpio_nrf5
shim is no longer needed.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
FE310 is the name of one SoC out of a range of products in the SiFive
Freedom line. The FE310 SoC port in Zephyr is compatible with all of
these products, so rename the SoC to SiFive Freedom
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Adds a shim layer around the imx gpio driver to adapt it to the Zephyr
gpio interface.
For now only the port 4 was tested.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Adds a driver for SX1509B I2C GPIO chip. This driver only supports the
basic GPIO features and does not currently implement the LED driver and
keypad matrix features.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Add gpio mcux driver which can be used for lpcxpresso54114 and other lpc
socs. In this driver, CMSIS register access is made for GPIO.
Option for access by GPIO Pin is provided as of now.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The PIO cores on Altera Nios-II processors can be used
for GPIOs and each PIO core can be configured as Input only,
Output only or as Bidirectional port from the Qsys tool.
The present Nios-II softcpu image on the Zephyr only has the
support for Output only port and the PIOs[0:3] are wired to
LED[0:3] on the Altera MAX10 board.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Adds a new gpio driver for the NXP i.MX family of SoCs. Read, write,
configure, and callback API functions are all implemented.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
