The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The length field for the MCUBOOT slot partitions in Nordic platforms
has always had an extra leading zero suggesting it's a 40-bit value,
being stored in a 32-bit field. Remove the incorrect leading zero to
reduce misunderstanding of the field.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the flags included in the new GPIO API to describe the properties of
LEDs and buttons in the device tree source files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Prepare for a day when all boards specify the chip select in the bus
devicetree node by making sure that the devicetree node associated
with arduino_spi uses the standard D10 pin from the arduino header as
the cs-gpios property value.
Also update the arduino tags in the board yaml files.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replaced NFFS mentions by LittleFS in all <board>.dts comments
to storage partitions.
Replaced NFFS by LittleFS in a few boards documentation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add SPI CS GPIO line to reel_board device tree. This is needed to make
the board work with Arduino SPI compatible shields.
Tested on reel_board (1507.1) and reel_board_v2 (1507.2).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add the green LED on the back of the reel_board to the device tree and
add PWM support for the front RGB LED.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Configure the pin connected to edge LED as PWM output.
On the new board version 1507.3 this pin also controls a buzzer.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We need to be able to specify GPIO flags in devicetree without that
preventing translation from the Arduino specifier to the host GPIO
specifier. Set up to ignore the low 6 bits of the flags field when
matching the child specifier, and to copy those bits to the parent
specifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit introduces separate "compatible" strings for DTS nodes
representing different types of Nordic SPI peripherals. Previously
"nordic,nrf-spi" was used for both SPI and SPIM. SPIS was already
handled separately.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/spi/
new binding for "nordic,nrf-spim" is added and common fields for all
3 types of Nordic SPI peripherals are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in spiX nodes are updated (when there is no
choice as only one type of SPI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/spi/
spi_nrfx_spim driver is updated with the new form of macros generated
from dts
* boards/
all spiX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of SPI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (SPI_x_NRF_SPI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
