The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since commit 5963ebaf33
("drivers: spi: CS configuration through devicetree")
the SPI GPIO CS flags are obtained from DT,
but the patch series has missed the necessary changes
in the device trees for displays and link_board_eth.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The length field for the MCUBOOT slot partitions in Nordic platforms
has always had an extra leading zero suggesting it's a 40-bit value,
being stored in a 32-bit field. Remove the incorrect leading zero to
reduce misunderstanding of the field.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The Kconfig PWM_[0-3] sybmols don't have any meaning for nrf family of
SoCs. The driver doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SoC node has compatibles for the specific SoC in place, having the
same compatible at the top level is technically a conflict and the
top-level one should really just be about the board. Remove the SoC
related compatibles at the top-level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Kconfig options that enable I2C and SPI instances are no longer used
in nRF drivers. Remove all assignments done to these options in related
board definitions, samples, and tests.
For nrf52_pca20020, also no longer needed setting of default values
for GPIO_SX1509B* options is removed (now the gpio_sx1509b driver is
enabled by default when a corresponding devicetree node is enabled).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `I2C_x_NRF_TWI*` that select
the type of nrfx driver (for TWI or TWIM peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding I2C node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between TWI and TWIM for a given instance.
Since all `I2C_x_NRF_TWI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the flags included in the new GPIO API to describe the properties of
LEDs and buttons in the device tree source files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Prepare for a day when all boards specify the chip select in the bus
devicetree node by making sure that the devicetree node associated
with arduino_spi uses the standard D10 pin from the arduino header as
the cs-gpios property value.
Also update the arduino tags in the board yaml files.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replaced NFFS mentions by LittleFS in all <board>.dts comments
to storage partitions.
Replaced NFFS by LittleFS in a few boards documentation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add SPI CS GPIO line to reel_board device tree. This is needed to make
the board work with Arduino SPI compatible shields.
Tested on reel_board (1507.1) and reel_board_v2 (1507.2).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add the green LED on the back of the reel_board to the device tree and
add PWM support for the front RGB LED.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
SOC_FAMILY_NRF has no prompt. Assignments in configuration files have no
effect on symbols without prompts. A prompt means the symbol is
user-configurable.
SOC_FAMILY_NRF is instead enabled indirectly through being selected by
other symbols.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Name convention for nordic USB driver changed
Kconfig files for custom boards have to be udapted accordingly.
Changes affect only name convention change.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Configure the pin connected to edge LED as PWM output.
On the new board version 1507.3 this pin also controls a buzzer.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We need to be able to specify GPIO flags in devicetree without that
preventing translation from the Arduino specifier to the host GPIO
specifier. Set up to ignore the low 6 bits of the flags field when
matching the child specifier, and to copy those bits to the parent
specifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit introduces separate "compatible" strings for DTS nodes
representing different types of Nordic SPI peripherals. Previously
"nordic,nrf-spi" was used for both SPI and SPIM. SPIS was already
handled separately.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/spi/
new binding for "nordic,nrf-spim" is added and common fields for all
3 types of Nordic SPI peripherals are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in spiX nodes are updated (when there is no
choice as only one type of SPI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/spi/
spi_nrfx_spim driver is updated with the new form of macros generated
from dts
* boards/
all spiX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of SPI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (SPI_x_NRF_SPI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Match the speed speficied for all boards using the jlink runner when
using the pyocd runner on the same board.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Use Device Tree,and in particular a new 'bt-c2h-uart' to select which
UART is being used to communicate with an external BLE Host when acting
as a Controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Hdc1008 driver is renamed into ti_hdc to prepare it to support all
available Texas Instruments HDC sensors (e.g. hdc1080, hdc2080).
Signed-off-by: Nikos Oikonomou <nikoikonomou92@gmail.com>
Enable pull-up on UART TX pin to reduce power consumption.
If the board is powered by battery the SoC consumes more
power than expected.
The consumption increases because TX pin is floating
(High-Impedance state of pin B from Dual-Supply Bus Transceiver).
Similar to commit b5b728495b
("boards: reel_board: enable pull-up on UART RX pin")
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
