Update boards that use to declare ethernet support to enable
matching ethernet node.
Similarly to other devices, use dts API to control ethernet pin
settings.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
nucleo_f767zi with soc cut-A (Device marking A) has some ethernet
restrictions.
Use of cut-Z is adviced.
fixes#26519
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
All pinmux supporting CAN, SPI and I2C of F7 series are added.
Since the F7 series supports up to two CANs,
the pin names of CANs have been changed.
Several minor pinmux errors have also been fixed.
Sorted by Alternate function.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Added / Tested support for RNG on the STM32F767ZI nucleo board.
Updated the SoC defconfig to auto-enable the driver when
ENTROPY_GENERATOR is enabled, and updated the board README.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_CAN flag to for each can pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_ADC flag to for each adc pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_PWM flag to for each pwm pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_I2C flag to for each i2c pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SPI flag to for each spi pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SERIAL flag to for each serial pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
For auto doc generation purpose, get name value of boards' yaml files
in sync with name provided as board name in .rst file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of CAN_X Kconfig symbols by access to dt instances
Control of enabled instances is now done using dts nodes status
field ('okay'/'disabled'). For boards supporting only can2,
can1 instance is disabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
ADC_1 peripheral instance was enabled by default in driver.
This is not the usual way to enable peripheral instances, as it
makes board configuration unclear.
Move activation in boards that are declaring ADC support.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
CONFIG_BOARD_FOO is enabled in a number of board *_defconfig files
although it is useless as it is set by default (as defined as a
one option choice, symbol defaults to 'y').
CONFIG_BOARD_FOO should remain only in target that are defined
in boards providing multiple choices (dual cores, board with multiple
revisions).
Clean it from STM32 impacted boards.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Added dts additions for stm32 nucleo f767zi board, also added
and modified soc addtions for thet board.
Updated dts reference file name.
Updated yaml to take out adc for now.
Signed-off-by: Roland Ma <rolandma@yahoo.com>
