The length field for the MCUBOOT slot partitions in Nordic platforms
has always had an extra leading zero suggesting it's a 40-bit value,
being stored in a 32-bit field. Remove the incorrect leading zero to
reduce misunderstanding of the field.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The SoC node has compatibles for the specific SoC in place, having the
same compatible at the top level is technically a conflict and the
top-level one should really just be about the board. Remove the SoC
related compatibles at the top-level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on nrf52840_pca10056 board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replaced NFFS mentions by LittleFS in all <board>.dts comments
to storage partitions.
Replaced NFFS by LittleFS in a few boards documentation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use Device Tree,and in particular a new 'bt-c2h-uart' to select which
UART is being used to communicate with an external BLE Host when acting
as a Controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add the bt-mon-uart chosen node to all the nRF-based boards so that they
can all use CONFIG_BT_DEBUG_MONITOR without additional changes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The current flash configurations for all nRF52840's in Zephyr is
VERY constrained when it comes to allowing samples any space for
storage or custom areas. It only leaves the last 4 pages of flash
for "storage".
The nRF52840 is also capable of using OpenThread which defaults
to using the last 4 pages of flash for storing OpenThread-related
network data.
This means that while using OpenThread under any configuration
designed to use mcuboot partition slots, there is no space left
over for storage of any kind.
Let's adjust the partition table to set storage at 8 pages of
flash (32k). This fixes the conflict with OpenThread and leaves
room for future use cases that may arise.
Signed-off-by: Michael Scott <mike@foundries.io>
This is a follow-up to commit e2b38e02bf.
Default PWM instances are enabled in Kconfig and DTS (with channel 0
set to LED0 pin) for these boards so that it is possible to build basic
samples blink_led and fade_led for them without extra modifications.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
As we want to remove dts dependency on Kconfig, we had a case based on
CONFIG_BOOTLOADER_MCUBOOT. From a DTS point of view that was just
getting the chosen property 'zephyr,code-partition' set. We can easily
move this to the actual dts files and remove the mcuboot.overlay.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the nrf52840_mdk
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In an effort to reduce the number of CONFIG_ defines in dts files, we
can remove CONFIG_MCUMGR_SMP_UART and just always set
'zephyr,uart-mcumgr' as there is no harm to always having this set for
those board dts files that define the property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
