The zephyr,code-parition was set incorrectly to SRAM. Set it to the
slot0 partition, so that enabling BOOTLOADER_MCUBOOT will place the code
at the proper address.
Signed-off-by: David Brown <david.brown@linaro.org>
The partition table in DTS are offsets within the flash device, not
absolute addresses. The flash doesn't start at 0 on the lpc55s6x
(because of the secure execution bit), but the offsets in the partition
table should.
Signed-off-by: David Brown <david.brown@linaro.org>
The OPENSDA_FW and LPCLINK_FW cmake variables are remnants of pre-west
days where we used an environment variable to set the desired debug host
tool, such as jlink or pyocd, based on which debug probe firmware was
loaded on the board. We now have two possible ways to do this, neither
of which requires the nxp-specific OPENSDA_FW or LPCLINK_FW variables:
1. Set standardized cmake runner variables when generating the build
system:
$ west build -- -DBOARD_FLASH_RUNNER=jlink -DBOARD_DEBUG_RUNNER=jlink
2. Use the west "--runner" argument with the debug and flash commands:
$ west debug -r jlink
Remove the now unnecessary OPENSDA_FW ond LPCLINK_FW variables and
update board documentation accordingly.
A few boards (frdm_kw41z, hexiwear_k64, mimxrt10{20,50,60,64}_evk)
reordered pyocd.board.cmake and jlink.board.cmake includes to preserve
the default runner when OPENSDA_FW was not explicitly set.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable GPIO as a workaround to enable some SPI slaves are not correctly
controlled using the Flexcomm SPI device.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Replace usage of deprecated GPIO_INT_ACTIVE_LOW, GPIO_INT_ACTIVE_HIGH,
GPIO_PUD_PULL_UP flags with a new equivalent in a few boards that were
added after 2.2 release.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Conditionalizes i2c pinmuxes on CONFIG_I2C for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes spi pinmuxes on CONFIG_SPI for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes serial pinmuxes on CONFIG_SERIAL for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Map Arduino interface to LPCXpresso55S69 pins.
Also tell which SPI interface is used by Arduino.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Map mikroBUS interface to LPCXpresso55S69 pins.
Also tell which SPI interface is used by mikroBUS.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Swap this out and make the status a parameter.
Leave a couple of cases of DT_NODE_HAS_COMPAT().
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
These are redundantly checking a node's status twice.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Map lpcxpresso55xxx type boards entropy device to rng peripheral.
Apllies to all versions of lpcxpress55s69 and lpcxpresso55s16.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The Kconfig I2C_[0-9] sybmols don't have any meaning for the majority of
SoCs. The drivers doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as usart. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as i2c. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
LPC55S69 CPU1 definition added.
Dual Core is not enabled!
Definitions related to dual core split of SoC's CPUs.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
LPC SoCs share the same register for all GPIO poarts. This leads us to a
device tree configuration that missmatches GPIO register address and
GPIO port identifier.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
LPC54114 to use D0 and D1 pinout.
LPC55S69 to use A0 and A1 pinout.
Pins enabled to be used as GPIO for 2 pin test gpio_basic_api.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Updates the mcux lpc driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle functions recently added to the gpio api.
ISR functions to be added later.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all lpc socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the lpc usart shim driver to more accurately reflect the
flexcomm hardware IP and to prepare for instantiating it on an SoC
outside the LPC family.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the high-speed spi instance 8 on the lpcxpresso55s69 board.
Configures pinmuxes and clocks, and updates board documentation
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In board pinmux.c ifdef of the form DT_GPIO_KEYS_SWx_GPIO_CONTROLLER
should be DT_GPIO_KEYS_SWx_GPIOS_CONTROLLER.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There are a few non-PNG (JPEG and WebP) files that are being
name as PNG files. This causes pdflatex/latexmk to fail due
to them not actually being PNG files. So rename those files
with correct extensions and update the RST files.
Also converted the WebP file in JPEG as PDFLatex cannot parse
WebP image.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Enables the pyocd runner on the lpcxpresso55s69 board. Note that this
currently requires building pycod from source to pick up fixes in
https://github.com/mbedmicro/pyOCD/pull/690
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
