Instead of having a board-specific config for this adc test, enable the
required battery-sense circuit by default at the board level when the
adc driver is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have an mcux shim driver, remove the old k64-specific
driver. Also remove include/drivers/k20_sim.h, since the old
k64-specific driver was the only thing left using it.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If the ftm driver is enabled, use the instance routed to the RGB led and
configure the pinmuxes as ftm channels instead of gpios.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that we generate BLUETOOTH_UART_ON_DEV_NAME, UART_PIPE_ON_DEV_NAME,
and BLUETOOTH_MONITOR_ON_DEV_NAME Kconfig defines for dts enabled
platforms add those into the appropriate dts files and remove from the
various board/Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables a usable adc driver instance based on the board design. No
additional pinmux configuration is necessary because a dedicated adc pin
is routed to the board's battery sense circuit. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add board metadata to be consumed by the sanitycheck script to provide
better matching with testcases and to test based on features declated in
the board files.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that NXP boards support 'make flash' and 'make debug' via pyOCD and
Segger J-Link, update all the NXP board docs accordingly. Adds a new
generalized OpenSDA document so certain details don't have to be
repeated for every OpenSDA board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a new debug support script using pyOCD and configures most NXP
boards so they can use it. frdm_kw41z is the one exception because pyOCD
doesn't yet support kw41z. Tested with pyOCD v0.8.0 and the latest
DAPLink firmware for each board.
Introduces two new environment variables, PYOCD_FLASHTOOL and
PYOCD_GDBSERVER, that allow you to set custom paths to the pyOCD tools.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new debug support script using Segger JLink and configures all
NXP boards so they can use it. Tested with Segger JLink GDB server
V6.14b and OpenSDA v2.1 firmware.
Change-Id: Ia1b297d9c93d21db61379e22f27ae54cda3ad461
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Adds fxas21002 and max30101 sensors to the list of supported features in
the hexiwear_k64 board document. Updates the pinmux table with the
sensor pins and sorts it by port name, then pin number.
Change-Id: I7d4c2c3b7b0e6e52b34e5675ce957c3bc5d18d46
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
For the SoCs in which all the boards for that platform are using dts we
can remove the Kconfig bits that are now coming from device tree.
Change-Id: Iccf4c84beb83fa1c516b6166f94de37b4a0162ae
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds DTS support for the Hexiwear K64 platform. This
includes enabling the DTS config option and adding conditionals around
the options to be replaced.
In addition, a DTS file is provided that customizes the Kinetis
platform to match the hexiwear board. A fixup file is provided to map
the generated information to the current client driver usage. This
file is temporary.
Change-Id: I247d538c6e13e0d1d4141fee74046575a7d2972e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Stop using the specific uart_k20 driver by default and start using the
more generic mcux uart driver instead.
Jira: ZEP-719
Change-Id: I7b107ea7118887591362159283ebb5413b45595a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The k64 gpio driver quietly initializes the pinmux to force the pin to
be a gpio, regardless of the setting defined by the board's pinmux
table, or even if the pin was not in the pinmux table.
This behavior caused the accelerometer interrupt pin to be incorrectly
defined in the frdm_k64f and hexiwear_k64 pinmux tables.
Change-Id: If46df0e051452fef291d5ad5cdff56463d5f465e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear_k64 i2c pinmux settings were copied over incorrectly when
the new mcux pinmux driver was created.
Change-Id: I72e5f8f7c06e2d9b08921109691edaf311f3811b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the uart console pins from the k64 soc init to the frdm_k64f and
hexiwear_k64 board pinmux tables. Not having these pins in the board
pinmux tables led one to believe that no pins in PORTB were being used
on the hexiwear_k64 board, and thus the port was incorrectly disabled by
default.
Also fixes PORTB to be enabled by default if the uart console is used.
Change-Id: Ide6b7b34dfba8a75a02a8f2bf37cce843afb92f1
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Merges the ksdk pinmux dev driver into the regular ksdk pinmux driver,
which now exposes the public pinmux API. Removes the private ksdk pinmux
API and converts the frdm_k64f and hexiwear_k64 boards to use the public
pinmux API.
Jira: ZEP-958, ZEP-1432
Change-Id: Ie5f60b604133093050b9c596050cad776d7b7cb3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Disable PORTA and PORTB by default on the hexiwear_k64 since there are
no pins in the pinmux table for these ports. Enable PORTE only if UART4
is enabled.
Change-Id: Ifdb01cacf0c475a9478454eb61474a930e22a628
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The basic blinky sample expects LED0_GPIO_PORT and LED0_GPIO_PIN macros
to be defined by board.h. The frdm_k64f and hexiwear_k64 boards don't
have a physical LED with this name, so create an alias to the green LED
to make the sample work.
Change-Id: I3426c571bb2e3165dbd9f4372d863b474c35fd5c
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
All pins from the existing pin init in
drivers/pinmux/k64/pinmux_board_hexiwear_k64.c were brought forward.
Jira: ZEP-1393
Change-Id: I3eb38dc435809cb7997d5884ff63bf8dd1e54720
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add defaults for the fxos8700 sensor, including which i2c instance, the
slave address, and interrupt pin.
Change-Id: Ib8a1e451ddfd84d2b2f19b0da846854acc969dcf
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Change the default Bluetooth UART device name to the UART connected to
the on-board kw40.
Change-Id: I2ae981bce31a58aed4dc6d3c378fc6f6a0bec76f
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The k64 SoC has multiple instances of many peripherals, but which
instances can actually be used depends upon the board design and pinmux
configuration.
Move all instance-specific default driver configurations from the SoC to
the boards (frdm_k64f and hexiwear_k64). Default driver selection
remains in the SoC (e.g., enable the KSDK I2C driver when I2C is
enabled).
This paves the way to support different driver defaults for the
frdm_k64f and hexiwear_k64 boards, but it does not yet change any of the
default values; it only changes where the default values get set.
Change-Id: Id9ed898762eb400ecefeac91ae4dce66da05622d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Introduce an architecture sorting of boards. This is to allow for
easier maintenance going forward as the number of boards grows. It
will be easier for any scripts to know the board/arch mapping without
having to maintain an explicit list of what boards are associated with
which arch. We can also do things like have architecture maintainers
cover reviews and branches for arch/${ARCH} and boards/${ARCH} going
forward.
Change-Id: I02e0a30292b31fad58fb5dfab2682ad1c5a7d5a7
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
