Both variables were used (with the same value) interchangeably
throughout CMake files and per the discussion in GH issue,
ZEPHYR_BASE is preferred.
Also add a comment with explanation of one vs. the other.
Tested by building hello_world for several boards ensuring no errors.
Fixes#7173.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The defconfig has CONFIG_SOC_MKL25Z=y, however CONFIG_SOC_MKL25Z doesn't
exist and should have been CONFIG_SOC_MKL25Z4, However its not
necessary to define this at all since it implied by the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The kl25z does not have the same spi hardware as the k64f and therefore
cannot use the same spi driver. Remove all references to spi for the
kl25z soc and frdm_kl25z board until we have a valid spi driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds led and button dts nodes to all kinetis boards and removes the
now unused preprocessor macros from board.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kl2x/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that the jlink runner supports the flash command, set
BOARD_FLASH_RUNNER when the OpenSDA or LPCLink debug adapter is
programmed with jlink firmware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Most boards enable the pinmux by default by setting CONFIG_PINMUX=y in
<board>_defconfig, but several boards did it in Kconfig.defconfig
instead. Several code reviews, such as #5043, have suggested using a
select in Kconfig.board to enable the pinmux, however this caused
warnings:
warning: (BOARD_LPCXPRESSO54114) selects PINMUX which has unmet direct
dependencies (BOARD_FRDM_K64F || BOARD_FRDM_KL25Z || BOARD_FRDM_KW41Z ||
BOARD_HEXIWEAR_K64 || BOARD_USB_KW24D512 || BOARD_GALILEO)
Fix how these boards enable the pinmux so they are more consistent with
other boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The various runners (flash/debug scripts) use environment variables to
take arguments. This is legacy behavior which is not desirable.
Use command line arguments instead.
Note: this leaves more general environment variables with publicly
documented behavior in place for now, for compatibility, e.g.:
ZEPHYR_FLASH_OVER_DFU, OPENSDA_FW, ESP_IDF_PATH, PYOCD_DAPARG
For example, when using dfu-util to flash arduino_101, instead of
setting DFUUTIL_PID, DFUUTIL_ALT, and DFUUTIL_IMG environment
variables, have the script invocation look like this:
python3 .../zephyr_flash_debug.py dfu-util flash \
[common arguments omitted] \
--pid=8087:0aba --alt=x86_app \
--img=.../build/zephyr/zephyr.bin
Make similar changes for other runners (openocd, etc.) and
targets (debug, debugserver).
To implement this in the scripts:
- have the individual scripts/support/runner/some-runner.py files
register their own command line arguments
- teach them to construct instances from arguments, not the
environment
- have zephyr_flash_debug.py request runners to register command
line argument parsers, and handle arguments
In the build system:
- add a new board_runner_args() extension function that board.cmake
files can use to add to the zephyr_flash_debug.py command line
- adjust cmake/flash/CMakeLists.txt to invoke with arguments
- add new helper include files for each runner (like
boards/common/dfu-util.board.cmake, etc.), which add default
options as needed and then add on overrides from
board_runner_args() calls
- update board.cmake files to use the new includes and extension
This implied some tweaking when using openocd to make the CMake string
escaping and unescaping work properly.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The Python-based runners have replaced the old shell scripts. Refactor
the build system accordingly:
- FLASH_SCRIPT is now BOARD_FLASH_RUNNER
- DEBUG_SCRIPT is now BOARD_DEBUG_RUNNER
The values, rather than being the names of files, are now the names of
runners in scripts/support/runner. They are still short, descriptive
names like "openocd", "jlink", "em-starterkit", etc.
Adjust the zephyr_flash_debug.py call and runner internals
accordingly. Have each runner class report a name and the commands it
can handle. This lets us move some boilerplate from each do_run()
method into the common run() routine, and enables further improvements
in future patches.
The handles_command() method is temporary, and will be replaced by a
more general mechanism for describing runner capabilities in a
subsequent patch. The initial use case for extending this is to add
device tree awareness to the runners.
To try to avoid user confusion, abort the configuration if an
xxx_SCRIPT is defined.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The old way of constructing FLASH_SCRIPT_ENV_VARS was corrupting the
values that were passed to the flasher. This new method is the
standard way of creating a dictionary/hashmap in CMake and does not
suffer from the same problem.
This fixes
https://github.com/zephyrproject-rtos/zephyr/issues/4844#event-1334599401
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable one adc channel on the SoC's PTB2 pin,
which is routed to the Arduino header A2 pin. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add board metadata to be consumed by the sanitycheck script to provide
better matching with testcases and to test based on features declated in
the board files.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that NXP boards support 'make flash' and 'make debug' via pyOCD and
Segger J-Link, update all the NXP board docs accordingly. Adds a new
generalized OpenSDA document so certain details don't have to be
repeated for every OpenSDA board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a new debug support script using pyOCD and configures most NXP
boards so they can use it. frdm_kw41z is the one exception because pyOCD
doesn't yet support kw41z. Tested with pyOCD v0.8.0 and the latest
DAPLink firmware for each board.
Introduces two new environment variables, PYOCD_FLASHTOOL and
PYOCD_GDBSERVER, that allow you to set custom paths to the pyOCD tools.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new debug support script using Segger JLink and configures all
NXP boards so they can use it. Tested with Segger JLink GDB server
V6.14b and OpenSDA v2.1 firmware.
Change-Id: Ia1b297d9c93d21db61379e22f27ae54cda3ad461
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In order to allow the use of such board, a very preliminar port was
developed. It consists of board files, as well as pinmux, uart, gpio,
spi drivers and device tree files.
Change-Id: I5753064e39e0b023cf4481744c176de26d8dbebb
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
