The OPENSDA_FW and LPCLINK_FW cmake variables are remnants of pre-west
days where we used an environment variable to set the desired debug host
tool, such as jlink or pyocd, based on which debug probe firmware was
loaded on the board. We now have two possible ways to do this, neither
of which requires the nxp-specific OPENSDA_FW or LPCLINK_FW variables:
1. Set standardized cmake runner variables when generating the build
system:
$ west build -- -DBOARD_FLASH_RUNNER=jlink -DBOARD_DEBUG_RUNNER=jlink
2. Use the west "--runner" argument with the debug and flash commands:
$ west debug -r jlink
Remove the now unnecessary OPENSDA_FW ond LPCLINK_FW variables and
update board documentation accordingly.
A few boards (frdm_kw41z, hexiwear_k64, mimxrt10{20,50,60,64}_evk)
reordered pyocd.board.cmake and jlink.board.cmake includes to preserve
the default runner when OPENSDA_FW was not explicitly set.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes the frdm_k64f and twr_ke18f boards to enable the kinetis
temperature sensor only if the sensor and adc drivers are both enabled.
This fixes a logging error seen at runtime in
samples/bluetooth/peripheral_hr.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
tested on mimxrt1060_evt
MEMORY_NOCACHE is needed
test on frdmk64f
special test slot need configure with
CONFIG_DMA_TEST_SLOT_START
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Conditionalizes can pinmuxes on CONFIG_CAN for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes ethernet pinmuxes on CONFIG_NET_L2_ETHERNET for all nxp
boards (kinetis, lpc, and imx families) to avoid possible conflicts
between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes pwm pinmuxes on CONFIG_PWM for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes adc pinmuxes on CONFIG_ADC for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes i2c pinmuxes on CONFIG_I2C for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes spi pinmuxes on CONFIG_SPI for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes serial pinmuxes on CONFIG_SERIAL for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Swap this out and make the status a parameter.
Leave a couple of cases of DT_NODE_HAS_COMPAT().
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
These are redundantly checking a node's status twice.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
As we phase out per instance Kconfig symbols convert to utilize
DT_DRV_INST to initialize CAN instances.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Kconfig I2C_[0-9] sybmols don't have any meaning for the majority of
SoCs. The drivers doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Kconfig PWM_[0-3] sybmols don't have any meaning for kinetis family
SoCs. The driver doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards moving uart mcux driver to DT_INST based, we need to convert
uses of CONFIG_UART_MCUX_[0-9] to use DT_NODELABEL instead. This way
the pinmux settings are still based on specific instances of the uart.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove all "supported: -hwinfo" definitions from the boards
yaml files and documentation. hwinfo can generally be tested
on every board because it returns -ENOTSUP if not supported.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The Kconfig board choice only has only one option which is implicitly
enabled, therefore it is not necessary to set the symbol explicitly in
board defconfigs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on frdm_k64f board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The DT_INST_* defines for the PWM controllers enabled in the device
tree are always defined causing the LED pins to always be set as PWM
outputs in the pinmux. Revert to using CONFIG_PWM_* for pinmux
configuration for now.
This reverts commit eb42a24dc6.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all kinetis socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable the NXP FTM PWM outputs in the board pinmux files based on the
DT_INST_* defines instead of CONFIG_PWM_* to match the pwm_mcux_ftm
driver.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Sorts the list of supported features in alphabetical order for all nxp
boards. No features are added or removed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Building `smp_svr` for this board results in a build error due to
undefined symbols `DT_NXP_KINETIS_UART_4006D000_*` which are related to
uart3 DTS symbols not being generated. This marks uart3's status as OK.
Signed-off-by: Fabio Utzig <utzig@apache.org>
We need to be able to specify GPIO flags in devicetree without that
preventing translation from the Arduino specifier to the host GPIO
specifier. Set up to ignore the low 6 bits of the flags field when
matching the child specifier, and to copy those bits to the parent
specifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update a number of boards that have arduino_gpio and arduino_i2c
support in their dts files to show that they support that in the
board.yaml file. This allows coverage on several shield tests that
utilize the tags 'arduino_gpio' and 'arduino_i2c'.
Exlucde stm32mp157c_dk2 from some of the samples right now since the
connector on the board doesn't support A2/A3. Also remove the duplicate
of exluding disco_l475_iot1.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instead of having a mix of west and CMake/ninja instructions for
building and flashing, document it using only west. This will help
clarify that west is the default build tool in Zephyr and should also
reduce confusion over what tool to use.
Note that the biggest change is changing the default in
doc/extensions/zephyr/application.py for :tool:, from all to west.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
