The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The on-board sensor has a enable pin that must be pulled
high in order to power the sensor.
Since no i2c sensor connected to ENV_I2C is supported by zephyr yet,
changed the pins of i2c1 to be connected to CCS811_I2C pins.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The nvs sample requires a storage_partition of 3 flash pages, but these
boards only provided 2 flash pages. Because of this the nvs sample
failed.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Convert the driver to use DT_INST_ defines, update all dependent dts,
soc and board files.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add entropy driver based on GECKO TRNG module along with device
tree support for EFM32PG and EFR32MG SOCs.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on efr32_slwstk6061a board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds the following:
- EFR32MG SoC support for the watchdog
- efr32mg_sltb004a board support for the watchdog
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
This commit adds support for the on-board flash MX25R8035F that is
directly connected to the efr32mg soc.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
This commit adds 'clock-frequency' property to the cpu nodes.
The clock frequency specified in the added property is used
during platform configuration. Examples:
- The SWO logger uses clock frequency to configure SWO output.
- Plenty of platforms need CPU clock specified for their HAL.
- Most of devices with USB needs information about CPU clock
in order to configure USB clock source.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
The EFR32™ Mighty Gecko Starter Kit EFR32MG-SLTB004A (a.k.a
Thunderboard Sense 2) contains a MCU from the EFR32MG12P family built
on ARM® Cortex®-M4F processor with low power capabilities.
There is an On-Board J-Link Debugger that presents a virtual COM port
for general purpose application serial data transfer with this
interface and a Mass Storage for firmware flashing.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
