The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
PA selection mainly depends on board design. So it looks like
device-tree is a better mechanism than Kconfig in this case. Use string
property with two possible values: "rfo" and "pa-boost".
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Only boards with at least 64K Flash will activate MPU because:
MPU + UERSPACE + All switches implicity activated
(CONFIG_MPU_STACK_GUARD, CONFIG_ARM_STACK_PROTECTION ...)
will consume about 40K Flash
(value computed on nucleo_f767_zi on tests/arch/arm/arm_ramfunc/).
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_I2C flag to for each i2c pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SPI flag to for each spi pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SERIAL flag to for each serial pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The LoRa shell and samples need a way to find the default LoRa
radio. Add the DT alias 'lora0' for the default radio.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove dts_fixup.h files that are not used (empty) or the defines aren't
used anymore and thus can be removed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This API will be deprecated in favor of the new API that clearly
specifies whether it works on logical or physical levels.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the lora/sx1276 driver to the new GPIO API, using configured
active level and the replacement interrupt and active-sensitive set
APIs.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add Add STM32_OSPEEDR_VERY_HIGH_SPEED flag for SPI1_SCK to function
properly. This is needed for the proper communication with the LoRa
modem. Without this flag, the received data is mangled when burst
read is performed.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
EEPROM drivers that support STM32L1 have been tested
on 96b_wistrio boards.
EEPROM support is added to the board documentation.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add support for 3.3v Low speed connector available on the Wistrio
board inorder to access peripherals in a board independent way.
Following peripherals are supported:
1. 7-GPIOs
2. I2C0
3. UART0
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The RAK811 module used on this board incorporates STM32L151CB-A SoC,
which has more RAM (32 KiB) compared to its companion STM32L151CB.
Hence, fix the doc, dts and Kconfig to include correct part number.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Move systick activation in soc/ as a Kconfig.defconfig file and
remove activation in boards _defconfig files.
This will allow to deactivate it in a more flexible way
with upcoming LPTIMER as tick source when power management
features are enabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix misspellings and doc issues missed during regular reviews (including
some files without a trailing newline)
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add board support for 96Boards WisTrio LoRa Tracker board from
RAK Wireless. This board is one of the 96Boards IoT Edition platform.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
