In order to avoid pin configuration conflicts between peripherals,
add CONFIG_I2C flag to for each i2c pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SPI flag to for each spi pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SERIAL flag to for each serial pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Allow the user to use software slave select instead of the
hardware pin, in order to free the related GPIO and avoid
unwanted SS triggering on the hardware pin. The default SS
is still the hardware pin.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We had a comment related to the #endif for CONFIG_USB_DC_STM32 however
the comment said CONFIG_USB_DC_STM, so fix it to match the ifdef.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move all STM32 based board pinmux files into the board dirs so we are
consistent across all the STM32 platforms/boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2017-09-12 11:24:56 -04:00
Renamed from drivers/pinmux/stm32/pinmux_board_carbon.c (Browse further)
