Enable I2S_STM32 in the soc common part, so it will no
longer be required in board default configuration.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
I2C interrupts usage should be the preferred way. This commit
enables them by default in the STM32 I2C driver itself.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Previous defconfig for dma is DMA_STM32F4X in this board, while the new
generic driver uses DMA_STM32 to enable DMA support, and also dma driver
of stm32 now needs HEAP_MEM_POOL_SIZE to be big enough to hold dma
stream instances.
Additional .conf files are added for also adding HEAP_MEM_POOL_SIZE
configuration to two test cases.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Remove configuration parameter CONFIG_BUS_TYPE. Now we may
make use of DT_ST_LSM6DSL_BUS_I2C and DT_ST_LSM6DSL_BUS_SPI
definition to select the bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit is taking care of following stuff:
1. pinmux: STM32F4 micro is using I2S5_CK and I2S_SD to interface with
on-board microphone.
2. default configuration:
- enable I2S5 and configure PLLI2S properly to generate
I2SxCLK = 128MHz.
- enable DMA
Note:
As stated in issue #9028 we needed to take care of a known SPI/I2S bug
implementing the following two actions:
A. APB2 clock has been slowed down to 42MHz.
B. The SPI/I2S clock gpio speed has been set to very_high_speed.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The choice symbol LSM6DSL_EXT0_LIS2MDL was given a 'default' in
Kboards/arm/96b_argonkey/Kconfig.defconfig, but 'default' has no effect
on choice symbols, triggering a warning from Kconfiglib.
Instead of adding a default to the choice symbol, change the default of
the 'choice' itself by giving it name and adding the default in
Kconfig.defconfig.
This requires that we remove the default on the "base" definition of the
'choice', due to some messiness related to the Zephyr-specific
prefer-later-defaults behavior (see the 'Zephyr-specific Kconfig
behavior for defaults' section in the Board Porting Guide). Choices were
overlooked when that patch was added to the C tools, meaning choices
still prefer earlier defaults. The crux is that Kconfig.defconfig files
are included last.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the named choices feature introduced by PR #6966
and configure LSM6DSL on ArgonKey board.
The two named choices introduced in LSM6DSL are:
- LSM6DSL_BUS_TYPE (default LSM6DSL_I2C)
- LSM6DSL_TRIGGER_MODE (default LSM6DSL_TRIGGER_NONE)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
ArgonKey board is a 96boards sensor hub platform for all 96Boards
compliant family products. The ArgonKey packs a Cortex-M4 chip
together with a set of motion, environmental and ambiental sensors
and can be used as a development platform for many different
applications.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
