STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In L4 series, select HAS_STM32CUBE is done per soc.
This could be factorized in Kconfig.series.
Aim is to lower the steps to add a new SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we generate BLUETOOTH_UART_ON_DEV_NAME, UART_PIPE_ON_DEV_NAME,
and BLUETOOTH_MONITOR_ON_DEV_NAME Kconfig defines for dts enabled
platforms add those into the appropriate dts files and remove from the
various board/Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With introduction of commit "pinmux: stm32: directly return error if
stm32_get_pin_config fails", pin configuration fails when
pins are not configured in pins[] array.
This was the case for configuration UART1 assigned on PB6/PB7.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
If the adc driver configuration is enabled (CONFIG_ADC=y), then enable
the mcux shim driver by default for all Kinetis SoCs.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux adc16 driver to adapt it to the Zephyr
adc interface.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add a STM32 LL based driver for the RNG processor. The RNG processor
is a random number generator, based on a continuous analog noise, that
provides a random 32-bit value to the host when read. The RNG passed
the FIPS PUB 140-2 (2001 October 10) tests with a success ratio of 99%.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enabled the boot_time test on ARM SoCs, set __start_time_stamp on ARM
since we don't have a free running counter similar to TSC on x86.
Also moved to printing the values out as %u to increase the range of
values.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In added mode flash operation are performed in timeslice
(in radio idle time).
Kconfig for mode enabling CONFIG_SOC_FLASH_NRF5_RADIO_SYNC.
Erase and write API implementations were rewritten and preserved against
concurrent execution.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Board port was done before the yaml transition, so was missing a
cc2650_sensortag.yaml. As such when we build all the test we get a few
build errors that we also fixed up.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add configuration and memory definitions to support STM32F103x8
Medium-density performance line SoC with 64 KB Flash.
Merge multiple files into single Kconfig.defconfig.stm32f103xx
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Since not all socs from f3 series (i.e stm32f334x8 no MPU) have MPU
capability, add capability only for MPU capable socs in Kconfig.soc
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
As other stm32 series support MPU, move common file in a file tree
useable by socs from other series
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clearing fields in the region descriptor attributes doesn't always have
the expected effect of revoking permissions. In the case of bus master
supervisor mode fields (MxSM), setting to zero actually enables read,
write, and execute access.
When we reworked handling of region descriptor 0, we inadvertently
enabled execution from RAM by clearing the MxSM fields and enabling the
descriptor. This caused samples/mpu_test run to throw a usage fault
instead of an MPU-triggered bus fault.
Fix this by setting all the MxSM fields to 2'b11, which gives supervisor
mode the same access as user mode.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Both the ARM and NXP MPU drivers incorrectly calculated the region index
by assuming the region type (e.g., THREAD_STACK_GUARD_REGION) was
zero-indexed, when in reality it is one-indexed. This had the effect of
wasting one region.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The NXP MPU requires special handling of region descriptor 0 to
guarantee that the debugger has access to the entire address space. It
does not allow writes from the core to affect the start or end
addresses, or the permissions associated with the debugger.
The original implementation of this driver attempted to work around
region descriptor 0, resulting in an off-by-1 error caught by Coverity.
Instead, define region descriptor 0 explicitly in the mpu_regions array,
and add some asserts to ensure that one doesn't try to change its start
or end addresses. This has an added benefit such that more permissions
can be enabled in region 0 if desired, whereas the previous
implementation always forced all writable permissions to be cleared.
Coverity-CID: 170473
Jira: ZEP-2258
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The original implementation of _get_num_regions() parsed the CESR[NRGD]
register field to determine the number of mpu region descriptors
implemented in hardware. There was a possible path in the code to return
zero, which would cause underflow later on in arm_core_mpu_configure().
Coverity complained despite an assert to catch this condition. Instead,
use a preprocessor macro from mcux that defines the number of mpu region
descriptors.
Coverity-CID: 169811
Jira: ZEP-2208
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stack sentinel doesn't prevent corruption, it just notices when
it happens. Any memory could be in a bad state and it's more
appropriate to take the entire system down rather than just kill
the thread.
Fatal testcase will still work since it installs its own
_SysFatalErrorHandler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
One of the stack sentinel policies was to check the sentinel
any time a cooperative context switch is done (i.e, _Swap is
called).
This was done by adding a hook to _check_stack_sentinel in
every arch's __swap function.
This way is cleaner as we just have the hook in one inline
function rather than implemented in several different assembly
dialects.
The check upon interrupt is now made unconditionally rather
than checking if we are calling __swap, since the check now
is only called on cooperative _Swap(). The interrupt is always
serviced first.
Issue: ZEP-2244
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The REGION bits (bit[3:0]) of MPU_RBAR register can specify the number
of the region to update if the VALID bit (bit[4]) is also set.
If the bit[3:0] of "region_addr" are not zero, might cause to update
unexpected region. This could happen since we might not declare stack
memory with specific alignment.
This patch will mask the bit[4:0] of "region_addr" to prevent updating
unexpected region.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
The kernel tracks time slice usage with the _time_slice_elapsed global.
Every time the timer interrupt goes off and the timer driver calls
_nano_sys_clock_tick_announce() with the elapsed time, this is added to
_time_slice_elapsed. If it exceeds the total time slice, the thread is
moved to the back of the queue for that priority level and
_time_slice_elapsed is reset to zero.
In a non-tickless kernel, this is the only time _time_slice_elapsed is
reset. If a thread uses up a partial time slice, and then cooperatively
switches to another thread, the next thread will inherit the remaining
time slice, causing it not to be able to run as long as it ought to.
There does exist code to properly reset the elapsed count, but it was
only compiled in a tickless kernel. Now it is built any time
CONFIG_TIMESLICING is enabled.
Issue: ZEP-2107
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add necessary Kconfig and minimal device tree in order to support
STM32F412ZG variant as found on the Nucleo STM32F412 board.
Origin: Original
Change-Id: Ic98a686f478ce551dc6101466ed0cf16924109e8
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver,
remove references to former native driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Align stm32f1xx series clock driver to other parts of stm32 family.
Driver support both Connectivity and Density lines of stm32f1 series,
that are based on different Reset and Clock Control architectures.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F413ZH has 1536kB of Flash and 320kB of SRAM. This
configuration is currently not supported by ST MPU driver, so fill in
the blanks.
Note: The MPU does not support region size that is not a power-of-2 (see
the SIZE field in the MPU_RASR register). This is a problem for our
1536kB Flash region, so it was rounded up to the nearest choice. This is
possible because the memory in the range 0x0818000 - 0x0FFFFFFF is
"Reserved" and thus not mapped anyway.
Change-Id: If0c3d1db564ca45e77f8b5bafa2afdbafa85b40f
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
pop {lr} instruction is not supported in ARMv6-M, fixed by
using pop {r0}; mov lr, r0; instructions.
Jira: ZEP-2222
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
We now have generic ARM M4 MPU support added to Zephyr.
Let's enable it for use with Nordic nRF52 chips.
Memory Layout was generated from Section 8.3 "Memory
Map" of nRF52 Product Specifications (for both nRF52832
and nRF52840):
0x00000000: Flash
0x10000000: Factory Information Config Registers
0x10001000: User Information Config Registers
0x20000000: SRAM
0x40000000: APB Peripherals
0x50000000: AHB Peripherals
0xE0000000: ARM M4 Private Peripheral Registers
NOT Configured:
0x60000000: External RAM
0x80000000: External RAM
0xA0000000: External Device
0xC0000000: External Device
NOTE: More work will be needed for future Nordic MWU (Memory
Watching Unit) support.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This patch add arm core MPU support to NXP MPU driver.
With this feature it is now possible to enable stack guarding on NXP
MPUs.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The STM32L4x SoCs embeds a slightly different embedded flash controller
from the STM32F4x SoCs.
This particular controller has the following properties :
- Up to 2 512KiB banks divided in 2KiB pages
- Flash can be accessed in any sizes
- Flash must be written in 64bit aligned 64bit double-words
The drivers/flash/flash_stm32f4x.c is refactored into a new common
drivers/flash/flash_stm32.c and drivers/flash/flash_stm32l4x.c is
created with the STM32L4x specific functions.
To ease the refactoring and keep common functions, the STM32L4x flash
headers are slightly modified to match the hardware reference naming
and solve compilation issues.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neither ASF nor CMSIS provide defines that can be processed by
the assembler. Exclude those from soc.h. Before this was done
incorrectly in board.h file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch converts Atmel sam3x MCU series to use register
header files from Atmel Software Framework (ASF) library.
By using ASF different Atmel SAM MCU series can use common
device drivers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch adds support for remaining Atmel SAM MCU series,
like sam3x to the common GPIO driver. After this update
full SAM MCU family should be supported by the driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add configuration, dtsi and memory configuration fixup for the
STM32F469XI High Performance SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch integrates the thread stack guard feature in the arm
Zephyr core.
Change-Id: I2022899cbc7a340be71cfaa52f79418292f93bae
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the arm core MPU implementation.
This implementation currently supports the thread stack guard feature.
Change-Id: I8b3795ebaf1ebad38aaddc2ed2f05535ead2c09a
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch add arm core MPU support to ARM MPU driver.
Change-Id: I5a61da4615ae687bf42f1c9947e291ebfd2d2c1d
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the arm core MPU interface, a common way to access the
pu functionalities by the arm zephyr kernel.
The interface can be divided in two parts:
- a core part that will be implemented by the arm_core_mpu driver and
used directly by the kernel
- a driver part that will be implemented by the mpu drivers and used by
the arm_core_mpu driver
Change-Id: I590bd284abc40d98b06fdf1efb5800903313aa00
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds initial MPU support to NXP K6x family.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent from running code located in SRAM.
This driver has been tested on FRDM-K64F.
Change-Id: I907168fff0c6028f1c665f1d3c224cbeec31be32
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add defines and pinmux arrays to support more UARTs on STM32F4.
Change-Id: Ib06c549bdb2b3d7065554a0a6d1a3d15441b29c9
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
It is useless to include the pinmux for a peripheral if it is not
enabled in the Kconfig. This is unnecessary and it increases the size of
the binary.
Define macros that will default to void if the associated Kconfig is not
enabled.
Change-Id: I0857fcef335c75b8bb6d537fd859f93d5be4a228
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Clean-up the pinmux arrays as a preparatory work before adding more
pinmuxes.
This is achieved by the following two actions:
- Define the PAD macro to simplify the [x - 1] = y construct
- Reorder the declartions by bank / pin to make it easier to
locate a pin among a high number of other pins, while minimizing the
risk of conflict when two people add a new declaration for two
different pins
Change-Id: I1ca0cc4f48bcd8cfd35b331e9821935f5c855876
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Add necessary Kconfig and minimal device tree in order to support
STM32F413xH variants as found on the Nucleo STM32F413 board.
Origin: Original
Change-Id: I60230c240d6acb610f16a02c62048d448476e9c5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The bitfield determining the I/O direction already defines the pin
as either input or output, cannot be none or both at the same time
This issue was reported by Coverity
Coverity-CID: 151970
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Not all the boards (for instance the Nuclo F412) use USART1 or USART2.
Let each board enable these USARTs when really used.
Change-Id: Idfe79c724bd7b1ab154310b4a8234b52eef2298d
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Commit 87893ddf7ad4 ("soc: stm32f429zi: rename SOC config flag") renamed
SOC_STM32F429XX to SOC_STM32F429XI but the text of the option should be
changed as well to reflect this restriction in scope.
Change-Id: I2627b59f805e73d6c8a3534e0feec71a4269c9ab
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Commit 599149dfb831 ("soc: stm32f407xg: rename SOC config flag") renamed
SOC_STM32F407XX to SOC_STM32F407XG but the text of the option should be
changed as well to reflect this restriction in scope.
Change-Id: Id03529452f5ec7d7ffee214b152c4aa555e1208a
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Rename SOC_STM32F407XX to SOC_STM32F407XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file).
Change-Id: I0afa16e86b7c99b9e685004f96beeb888f9e7568
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename SOC_STM32F429XX to SOC_STM32F429XI to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: Id188b7703d2bce0a3ded09132ff0f205efa9c143
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The xC tag in the SoC reference indicates the flash size, use it in the
configuration to permit selection of correct flash size for dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch enables the generation of the ARM CMSDK UART base address
from the device tree.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This places a sentinel value at the lowest 4 bytes of a stack
memory region and checks it at various intervals, including when
servicing interrupts or context switching.
This is implemented on all arches except ARC, which supports stack
bounds checking directly in hardware.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Unline k_thread_spawn(), the struct k_thread can live anywhere and not
in the thread's stack region. This will be useful for memory protection
scenarios where private kernel structures for a thread are not
accessible by that thread, or we want to allow the thread to use all the
stack space we gave it.
This requires a change to the internal _new_thread() API as we need to
provide a separate pointer for the k_thread.
By default, we still create internal threads with the k_thread in stack
memory. Forthcoming patches will change this, but we first need to make
it easier to define k_thread memory of variable size depending on
whether we need to store coprocessor state or not.
Change-Id: I533bbcf317833ba67a771b356b6bbc6596bf60f5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The FPGA on the MPS2 board implements 4 SBCon devices for I2C which are
connected to:
- a touchscreen controller
- the audio device (for configuration)
- both shield connectors
Change-Id: I55ca985e18b45d68f5e7421c4768dfc9bf2fcb3f
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Converted Stellaris UART driver over to utilize device tree generated
defines. Added a yaml description for the uart, and converted over the
ti_lm3s6965 SoC & qemu_cortex_m3 board port over to utilize it.
Change-Id: Ie20844eb63d2c68eb59ad4160f7f5b5a35e2943b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a simple device tree for the TI lm3s6965 SoC and QEMU
Cortex-M3 board port. We get flash and memory base addresses and sizes
from the device tree as well as the ARM NVIC number of priority bits.
Change-Id: I4452b5543de7be55518997e54837ccbfd4f121df
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reorder config entries alphabetically to make it easier to add new ones.
Change-Id: Ib118405a150a408638232513fba7198b458ecfa7
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Now that all the nRF based board/SoCs have device trees, we can remove
the Kconfig bits that are now coming from device tree.
Change-Id: Ia1a870a50582d4109070d2833660f58fd6f8691f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF51822 SoCs and Arduino 101-BLE,
Curie-BLE, BLE Nano, PCA10028-DK, and Quark-SE BLE boards. This
is minimal support for memory, flash, and UART.
Change-Id: I7e572bea537e384b6d66e520462f023ace0c9b35
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fixup the nRF52840-QIAA to allow getting its SRAM & FLASH sizes from
device tree.
Change-Id: I67ecd7da5f0472402064f158030d9f97f49d7d20
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Nothing calls _ScpMainOscEnable, so lets remove it and associated files
that aren't used anymore.
Change-Id: Ibe900d039c531c4da56baa673d309ee961b09e52
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Cleanup soc code to enable UART_MCUX_LPSCI to support UART0.
Change-Id: I173febffcffc902f228946124e0434f122a67607
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a shim layer around the mcux lpsci driver to adapt it to the Zephyr
serial interface.
Change-Id: I024f1605e3194f34bb57e8a121900e05b3085a82
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for STM32L475xG SoC as a preliminary for
Discovery IOT board support.
stm32l476.dtsi file is now including stm32l475.dtsi
since STM32L476 SoC is a STM32L475 SoC with LCD support
Change-Id: I7567255e4172231cbf4899474617ecae0cd68d64
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of stm32 common clock driver for stm32f4 series
remove references to stm32f4 specific driver.
Change-Id: I372a0ea046007bcb34944d6b2b8880077583b1d3
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit disables native stm32f4x clock control
driver and enables stm32 LL clock control driver
for stm32f4 family
Jira: ZEP-2039
Change-Id: I98ba6c89c4a3a1f39658c5808cd47a2d1f344130
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit enables STM32Cube LL based driver for stm32f4 series.
This generic driver provides a unified API to clock driver for all
stm32 series.
LL API allows driver to be lightweight and to keep genericity across
stm32 family to ease further devlopment and maintenance.
Change-Id: Ie31ae8f433313787f9c9eda77de41925721d54dd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The CC3220SF is a replacement for the CC3200 SoC, comprising
a network coprocessor and Cortex-M4 MPU.
This leverages the CC3220 SDK driver peripheral library in ROM,
and some files built from ext/hal/ti/.
Jira: ZEP-1958
Change-Id: I892b212c178e05d84ff1d716dde593ced653ae6d
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Adds event based scheduling logic to the kernel. Updates
management of timeouts, timers, idling etc. based on
time tracked at events rather than periodic ticks. Provides
interfaces for timers to announce and get next timer expiry
based on kernel scheduling decisions involving time slicing
of threads, timeouts and idling. Uses wall time units instead
of ticks in all scheduling activities.
The implementation involves changes in the following areas
1. Management of time in wall units like ms/us instead of ticks
The existing implementation already had an option to configure
number of ticks in a second. The new implementation builds on
top of that feature and provides option to set the size of the
scheduling granurality to mili seconds or micro seconds. This
allows most of the current implementation to be reused. Due to
this re-use and co-existence with tick based kernel, the names
of variables may contain the word "tick". However, in the
tickless kernel implementation, it represents the currently
configured time unit, which would be be mili seconds or
micro seconds. The APIs that take time as a parameter are not
impacted and they continue to pass time in mili seconds.
2. Timers would not be programmed in periodic mode
generating ticks. Instead they would be programmed in one
shot mode to generate events at the time the kernel scheduler
needs to gain control for its scheduling activities like
timers, timeouts, time slicing, idling etc.
3. The scheduler provides interfaces that the timer drivers
use to announce elapsed time and get the next time the scheduler
needs a timer event. It is possible that the scheduler may not
need another timer event, in which case the system would wait
for a non-timer event to wake it up if it is idling.
4. New APIs are defined to be implemented by timer drivers. Also
they need to handler timer events differently. These changes
have been done in the HPET timer driver. In future other timers
that support tickles kernel should implement these APIs as well.
These APIs are to re-program the timer, update and announce
elapsed time.
5. Philosopher and timer_api applications have been enabled to
test tickless kernel. Separate configuration files are created
which define the necessary CONFIG flags. Run these apps using
following command
make pristine && make BOARD=qemu_x86 CONF_FILE=prj_tickless.conf qemu
Jira: ZEP-339 ZEP-1946 ZEP-948
Change-Id: I7d950c31bf1ff929a9066fad42c2f0559a2e5983
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Future tickless kernel patches would be inserting some
code before call to Swap. To enable this it will create
a mcro named as the current _Swap which would call first
the tickless kernel code and then call the real __swap()
Jira: ZEP-339
Change-Id: Id778bfcee4f88982c958fcf22d7f04deb4bd572f
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Found out that the SAM3 series is not a single series. There are actully
3 different series, 3U, 3A, and 3X.
Origin: Original
Jira: ZEP-2067
Change-Id: I61cdc826cc32dbdd25b5e6bafaada062c8ae8417
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Historically, space for struct k_thread was always carved out of the
thread's stack region. However, we want more control on where this data
will reside; in memory protection scenarios the stack may only be used
for actual stack data and nothing else.
On some platforms (particularly ARM), including kernel_arch_data.h from
the toplevel kernel.h exposes intractable circular dependency issues.
We create a new per-arch header "kernel_arch_thread.h" with very limited
scope; it only defines the three data structures necessary to instantiate
the arch-specific bits of a struct k_thread.
Change-Id: I3a55b4ed4270512e58cf671f327bb033ad7f4a4f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Moved the Atmel SAM 3 from its own directory into
the directory tree laid out in arch/arm/soc/atmel_sam.
Origin: Original
Jira: ZEP-2067
Change-Id: I26a1a521dd7caa607c3e95a06cd574ee68ca59b8
Signed-off-by: Justin Watson <jwatson5@gmail.com>
This patch adds initial MPU support to STM32F401XE.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent the application to access to the BootROM.
* Prevent from running code located in SRAM.
Change-Id: I4dc0669009bd5c0a829a69f8ff417c787b7043ed
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds initial MPU support to ARM Beetle.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent from running code located in SRAM.
Change-Id: I64f1001369896fffb0647de6be605a95161c4695
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds an initial driver for the ARM MPU.
This driver has been tested on ARM Beetle and STM32F4.
Change-Id: I2bc4031961ec5a1d569929249237646f4a349f16
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch add the Memory Protection Unit parameter to the arm core
configuration.
Change-Id: Ifee8cdd5738391a6f182e8d0382d27eeb8c546ba
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Marc Moreno <marc.morenoberengue@linaro.org>
This patch adds the regions for the mpu configuration to the soc.h file.
Change-Id: Ifd1ce96eeb4731ae01f5171924af92b9e236a3dc
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Marc Moreno <marc.morenoberengue@linaro.org>
Document the flash latency values by copying the relevant tables
from the reference manuals for each MCU.
Change-Id: Ieb2824ffd7634d917399e3e62146d9243b527f44
Signed-off-by: Christer Weinigel <christer@weinigel.se>
If the flash latency isn't set most STM32F4xx MCU's won't be able
to run from flash when the CPU frequency is changed. Make this a
compile time error instead of an assert at runtime.
Change-Id: Ic3421194545f8f83bd6e00f0cd011306c8d1eedd
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Put the reason code in r0 and make a SVC #2 call, which will be
propagated to _fatal_error_handler as an exception.
The _is_in_isr() implementation had to be tweaked a bit. User-generated
SVC exception no longer just used for irq_offload(); just because we are
in it does not mean we are in interrupt context. Instead, have the
irq_offload code set and clear the offload_routine global; it will be
non-NULL only if it's in use. Upcoming changes to support memory
protection (which will require system calls) will need this too.
We free up some small amount of ROM deleting _default_esf struct as it's
no longer needed.
Issue: ZEP-843
Change-Id: Ie82bd708575934cffe41e64f5c128c8704ca4e48
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Unlike assertions, these APIs are active at all times. The kernel will
treat these errors in the same way as fatal CPU exceptions. Ultimately,
the policy of what to do with these errors is implemented in
_SysFatalErrorHandler.
If the archtecture supports it, a real CPU exception can be triggered
which will provide a complete register dump and PC value when the
problem occurs. This will provide more helpful information than a fake
exception stack frame (_default_esf) passed to the arch-specific exception
handling code.
Issue: ZEP-843
Change-Id: I8f136905c05bb84772e1c5ed53b8e920d24eb6fd
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The ICSR RETTOBASE bit is improperly implemented in QEMU (the polarity
is flipped) and the fix for it has not yet made it into a QEMU release,
although it is present in upstream master branch.
The symptom is that if we are not in thread mode, the system always
believes were are in a nested exception state, causing _IsInIsr() to
always return true.
Skip the nested exception check if we are building for QEMU.
This is a workaround until SDK-54 is resolved.
Issue: SDK-54
Change-Id: I06eafcc85fb76a9b23b4ba85ed6e111a08516231
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For exceptions where we are just going to abort the current thread, we
need to exit handler mode properly so that PendSV can run and perform a
context switch. For ARM architecture this means that the fatal error
handling code path can indeed return if we were 1) in handler mode and
2) only wish to abort the current thread.
Fixes a very long-standing bug where a thread that generates an
exception, and should only abort the thread, instead takes down the
entire system.
Issue: ZEP-2052
Change-Id: Ib356a34a6fda2e0f8aff39c4b3270efceb81e54d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We do the same thing on all arch's right now for thread_monitor_init so
lets put it in a common place. This also should fix an issue on xtensa
when thread monitor can be enabled (reference to _nanokernel.threads).
Change-Id: If2f26c1578aa1f18565a530de4880ae7bd5a0da2
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We do a bit of the same stuff on all the arch's to setup a new thread.
So lets put that code in a common place so we unify it for everyone and
reduce some duplicated code.
Change-Id: Ic04121bfd6846aece16aa7ffd4382bdcdb6136e3
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There are a few places that we used an naked unsigned type, lets be
explicit and make it 'unsigned int'.
Change-Id: I33fcbdec4a6a1c0b1a2defb9a5844d282d02d80e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types. This handles the remaining includes and kernel, plus
touching up various points that we skipped because of include
dependancies. We also convert the PRI printf formatters in the arch
code over to normal formatters.
Jira: ZEP-2051
Change-Id: Iecbb12601a3ee4ea936fd7ddea37788a645b08b0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types. There are few places we dont convert over to the new
types because of compatiability with ext/HALs or for ease of transition
at this point. Fixup a few of the PRI formatters so we build with newlib.
Jira: ZEP-2051
Change-Id: I7d2d3697cad04f20aaa8f6e77228f502cd9c8286
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix doxygen comment typos used to generate API docs
Change-Id: I94df2e3a2bda248824ed2aeff3dd0eb743f0bf3e
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add soc_gpio_get(), soc_gpio_debounce_length_set() functions to Atmel
SAM soc_gpio driver.
Change-Id: I541c6fead9a308dd2e67c59dabe67b87cf1628ef
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added serial (UART) driver for Atmel SAM MCU family.
Note:
- Error handling is not implemented
- The driver works only in polling mode, interrupt mode is
not implemented.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1959
Change-Id: I3e770fd1feb2ddf92cf405a9aa17be92eb32e19b
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added I2C bus (TWIHS) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1866
Change-Id: Ic5aa7b6b21295feccae883d580b38bbeaf2ce291
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add plumbing to build system and SoC level dtsi for the NRF52832 SoC.
We additionally add the necessary yaml files for the UART on the NRF52
SoCs.
Change-Id: I3b4a821b2993827e33d8e84bdbbc759d1521f8bd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce SoC specific config options similar to what exists on NRF51,
this is mostly to help distinguish between SRAM & Flash sizes on
different variants.
Also deleted some unnecessary setting of CONFIG_SOC_NRF528{32,40} in the
board defconfig files.
Change-Id: I3aaedf0c15423ae12636f87b8e6a39070cbb2c6f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds initial support for the kw40z SoC. This SoC has all the same
peripherals as the kw41z but with less flash and ram, so the defconfig
and dts are nearly the same.
Jira: ZEP-1388
Change-Id: Ib804451e8c2c71c4ff7d342bf23f6567d1542a2d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The KL2x support requires DTS so we can remove any !HAS_DTS references.
Also NUM_IRQS shouldn't have been in a !HAS_DTS ifdef block.
Change-Id: I12b0781b6eef100bfb0a94698d12fc519c759888
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since all STM32 SoCs are using device tree we can remove this last bit
of !HAS_DTS for getting flash/sram sizes from Kconfig.
Change-Id: I9e706b7aba7c0edcf9fca3ddc0ddc7d820980b47
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted over all STM32F3 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F3.
Boards that are now using devicetree:
* Nucleo f334r8
* STM32373C Eval
Change-Id: I081a1d83f86e417a98b6864c745354b6b32953b7
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted over all STM32F1 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F1. Also
renamed the STM32F10{3,7} SoC dtsi to try and make it clear that the 'X'
is a place holder. Fixedup the top level compatiables in the boards to
be the specific 'X' instead of the generic one.
Boards that are now using devicetree:
* Nucleo f103rb
* STM3210C Eval
* STM32 MINI A15
Change-Id: I29b3634ec7451f974687d55980414efa655e2e96
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted over all STM32F4 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F4.
Boards that are now using devicetree:
* 96b_carbon
* nucleo f401re
* nucleo f411re
Change-Id: Ibe197ca0a3f5ad78d594485a578d986403cc824a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since all the L4 SoCs are using DTS we can remove the various Kconfig
bits that we now get from DTS.
Change-Id: Icdec49b478ff285dc3347b09412964a721f75bbf
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to suppport the FRDM-KL25Z board,
it is necessary to make this soc available.
Change-Id: Id93a51dcc9ef58118e27db02c30f662eb73d5adb
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
Instead of FLASH_LOAD_OFFSET being something specific to cortex-m, add
it generally to misc/Kconfig, along with a hidden config
HAS_LOAD_OFFSET which can be selected by the architectures as they add
support for the functionality.
Change-Id: I256ff8cf4e9b8493b26354c3b93fe1f7017d4887
Signed-off-by: David Brown <david.brown@linaro.org>
same70/soc.h provided IRQ ids as #define. This is no longer
necessary as gen_isr_tables mechanism, which was recently
introduced, supports IRQ ids as enums. These are provided
directly by Atmel ASF library.
Change-Id: I3c2573d97d81eb9a02e85fde0566622ff2ecf2cf
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
These are fixed I/O registers for getting and setting the states of
LEDs, buttons, SPI chip-selects, and LCD control lines. It also contains
several free-running counters with no specific use.
Change-Id: Ib49306d5501574f7eb354165cdca6f29e3d4dad4
Signed-off-by: Jon Medhurst <tixy@linaro.org>
For the SoCs in which all the boards for that platform are using dts we
can remove the Kconfig bits that are now coming from device tree.
Change-Id: Iccf4c84beb83fa1c516b6166f94de37b4a0162ae
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As part of the transition to Device Tree, a temporary
HAS_DTS configuration variable, and a .fixup file per board
with symbol aliases were added.
This patch removes the cc32xx related fixup file
definitions, except for those used additionally outside
the cc32xx drivers.
Since cc32xx has DTS files, and since HAS_DTS will always be true,
it also removes the 'if !HAS_DTS' blocks from the cc32xx Kconfig
files.
Change-Id: I1c1b9f734795f523342f82ab32f2a38983812c0b
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move back to getting the number of IRQs from Kconfig. We do this
because the number of IRQs should really just be determined by scanning
the device tree and figuring out the highest IRQ value used.
Change-Id: I8e0dbec1d9d036d4e899b237c4dc7d833c422e18
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch updates the ARM core to use struct k_thread instead of struct
tcs. Struct tcs has been deprecated with Zephyr 1.6.
Change-Id: I1219add0bbcca4b963ffe02cd4519eca355c7719
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The Cortex-M4 of the STM32F4 family has an FPU. Enable the FPU support
by selecting CPU_HAS_FPU.
Change-Id: Iddae9c547df6e010562649eb0997dc61563c8fc4
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The comment refers to STM32F1 instead of STM32F4.
Change-Id: Ide116b712146f87a6f4d2aaafea8bd181c4d9397
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The current implementation of stm32_gpio_set() uses the GPIO output data
register to change the state of individual GPIOs. The generated
assembler needs at least 3 instructions: load / modify / store.
This opens a small race window, for example if a thread and an
interrupt both try to change the state of the same GPIO bank.
Use the GPIO bit set/reset register to perform the atomic change without
locking.
This also has the benefit of a more optimised implementation, which can
be useful for GPIO-intensive work. Compare the new version:
08000c98 <stm32_gpio_set>:
8000c98: f001 010f and.w r1, r1, #15
8000c9c: 2301 movs r3, #1
8000c9e: b902 cbnz r2, 8000ca2 <stm32_gpio_set+0xa>
8000ca0: 3110 adds r1, #16
8000ca2: 408b lsls r3, r1
8000ca4: 6183 str r3, [r0, #24]
8000ca6: 2000 movs r0, #0
8000ca8: 4770 bx lr
and the old one:
08000c98 <stm32_gpio_set>:
8000c98: 2301 movs r3, #1
8000c9a: f001 010f and.w r1, r1, #15
8000c9e: fa03 f101 lsl.w r1, r3, r1
8000ca2: 6943 ldr r3, [r0, #20]
8000ca4: b10a cbz r2, 8000caa <stm32_gpio_set+0x12>
8000ca6: 4319 orrs r1, r3
8000ca8: e001 b.n 8000cae <stm32_gpio_set+0x16>
8000caa: ea23 0101 bic.w r1, r3, r1
8000cae: 6141 str r1, [r0, #20]
8000cb0: 2000 movs r0, #0
8000cb2: 4770 bx lr
Change-Id: Ie5800d1c345016028d1b9a099f5d74cac35f592a
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
In prep for supporting the older KL2x SoCs that use a different SPI
block, rename the current SPI driver to DSPI to match what the MCUX HAL
defines it as.
Change-Id: I9097580df5fca649ab6fd9a38212fced0b1ea6ed
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the necessary changes to enable use of DTS for
generating required build information.
Change-Id: I0d7aa15488339a425ffe57b6354992851212f7f3
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The previous file contained erroneous values of the number of IRQs
in these socs.
Change-Id: Ie7d2c19d86e247599f4924b95d9330175140d894
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
The current nordic hal layer in ext/ requires additional macros to
include the correct files. This will be corrected in an upcoming version
of the hal layer itself but for now add the required macros so that
users can benefit from the hal peripheral code.
Change-Id: I95127d0a98d7e882fdc779f961718fa223d504eb
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This directory now handles all of Cortex-M0, Cortex-M3/M4. So, just
consistently use "Cortex-M" (as used by number of files already)
without refering to a particular subarch. Also, consistently (letter
casing) spell it as "Cortex-M". A typo is fixed too.
Change-Id: I42ee09abc9a503381bca4ae437c83a8f48816ebc
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In Atmel SAM Family of MCUs, the watchdog is enabled by default at boot.
The watchdog once disabled, cannot be re-enabled back without a reset.
Hence disabling the Watchdog needs to be handled via the Watchdog driver.
Tested on Atmel SAMV71 Xplained Ultra Evaluation Kit.
Jira: ZEP-1684
Change-Id: I5682c3f007a846b064b8d16abf0d9b67d4c8e7d6
Signed-off-by: Souvik K Chakravarty <souvik.k.chakravarty@intel.com>
Help text in Kconfig files should be indented with <tab><space><space>.
Change-Id: Iefa5c8f4bfe329b4ee754ebfe43766f445432184
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Provide a random driver wrapped around the MCUX TRNG driver.
Change-Id: Icbd7ab587aa18ecbd7eae52290aaa5d8ee504cf2
Origin: Original
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
MCUX contains more than one type of random number generator,
so refrect this in config and file names.
Change-Id: Iba4482a1ae41f35d471686f8b159c113147c4df8
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Cube HAL implements timeout based on 1ms tick.
This commit allows Cube HAL to get Zephyr system clock.
Change-Id: I9a59edcf6fa8e0ebfd5040348db537dadd9fcdfa
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to support the discovery STM32F4 and STM32F429 boards,
it is necessary to make these socs available.
Change-Id: I351d294fb02c4385f291a6e258a3f7d81e85627e
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
Currently, ARM Cortex-M image ROMs are linked starting at the flash
device's base address (CONFIG_FLASH_BASE_ADDRESS). This prevents XIP
Zephyr applications from being linked to run from elsewhere on the
flash device. Linking Zephyr applications to run from elsewhere can be
necessary when running under a bootloader (i.e., booting into a Zephyr
application from a bootloader, not using Zephyr as a bootloader).
To enable this use case, add a new config option: FLASH_LOAD_OFFSET.
This option directs the linker to treat ROM as if it started that many
bytes from the base of flash on Cortex-M targets. The option defaults
to zero to preserve backwards compatibility.
Change-Id: I64f82aee257c19c2451f9789b0ab56999775b761
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
The wrong UART was set on for the qemu_cortex_m3 slip (uart pipe) device
Change-Id: If6d6af0f32ef02ccc559cd1fff90ea499cc378c4
Signed-off-by: Richard Peters <mail@richardpeters.de>
This replaces the hard-coded vector table, as well as the
software ISR table created by the linker. Now both are generated
in build via script.
Issue: ZEP-1038, ZEP-1165
Change-Id: Ie6faaf8f7ea3a7a25ecb542f6cf7740836ad7da3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch moves the include for the generated_dts_board.h inside of
the include/arch/arm/arch.h file. This was done to simplify the
includes required for files. Only two files will include the dts
generated include file directly: arch.h and the linker.ld
Change-Id: I2614f4fd4eeed2ab635a3264d7dac8b83f97b760
Signed-off-by: Andy Gross <andy.gross@linaro.org>
We now use CMSIS for ARM Cortex-M SoCs so we can remove the last bits of
scs and scb.
Jira: ZEP-1568
Change-Id: I0c7c45b0321dc402ed594e9faffb5109922edcf0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Coverted:
_ScbMemFaultMmfarReset
_ScbBusFaultBfarReset
_ScbUsageFaultAllFaultsReset
To use direct CMSIS register access.
Also removed scb.h and references as there is no longer any code in it.
Jira: ZEP-1568
Change-Id: I469f6af39d1bd41db712454b0b3e5ab331979033
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The previous code incorrectly used the value 0xfe to clear the mem and
bus faults. It attempted to handle the address register valid bits
separately, but reversed the bit order.
Jira: ZEP-1568
Change-Id: I240d072610af9979ca93c0081ed862df08929372
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converted access to CFSR MMFSR, BFSR, and UFSR to use direct CMSIS
register access when printing out the values of those registers.
Jira: ZEP-1568
Change-Id: I7969bb81346327637140ec23d91422a6bfaef032
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Coverted:
_ScbBusFaultAddrGet
_ScbMemFaultAddrGet
To use direct CMSIS register access
Jira: ZEP-1568
Change-Id: Ic49b3ac3fc4fb63d413f273569c77f6539e4e572
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Pin number should be decremented by 8 if the pin
refers to the GPIOx_AFRH register.
Change-Id: I76e960f3b4adc3c2139ef5a88f15dbe98603228e
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
Following activation of Cube LL based clock control driver,
this commits cleans up the useless structures for RCC definitions
and remove code relative to native F3 Clock control driver.
Change-Id: I6f3ee44adb09adc52927eb4b05f8a829665eb96d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of Cube LL based clock control driver,
this commits cleans up the useless structures for RCC definitions
and remove code relative to native L4 Clock control driver.
Change-Id: Ic0408d5f5ec66651d46d13dfaf447da2666367cd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32f3x soc.
Clean up will have to be done afterwards.
Change-Id: I20480579f12a6fc1f1f6a51589981ac3f1d63ef0
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32l4x soc.
Clean up will have to be done afterwards.
Change-Id: I979a4169148c5fe5a0693d182d2d17f9ffaf1c77
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This patch adds DTS support to the ARM CMSDK UART driver. The DTS
currently specifies the IRQ, IRQ PRIO, and base address of the port.
Change-Id: I8e5bc81c013958be4297d563495bf126b53a83a9
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the base DTS support for the V2M Beetle board. The
initial set of changes include SRAM, FLASH, and IRQ controller support.
Change-Id: I06685622b9c57ac358544c71350074ce06e3371e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds all the necessary changes to enable use of DTS for
generating required build information.
Change-Id: Ia476fbb14c7d9d6b9db3340c73f599556a880da3
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch ifdef's out information that would be redefined by
information generated from DTS. This patch also fixes up the serial
drives to work properly with the DTS generated information.
Change-Id: I912ccf35be23c107705a4866e5a68b3b51154ffa
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support and related files for the NXP Kinetis
platform. The DTS files contain the base definitions for the hardware
nodes on Kinetis platforms. The YAML files provide the definitions of
the contents of the DTS nodes.
The Kconfig changes were put in place to allow for the conversion of
existing drivers. Once those drivers are modified, the Kconfig options
that are replaced by the DTS information will be removed.
Change-Id: If110fffa99c0b12471cf2df206da6687277e4756
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for using device tree configuration files for
configuring ARM platforms.
In this patch, only the FLASH_SIZE, SRAM_SIZE, NUM_IRQS, and
NUM_IRQ_PRIO_BITS were removed from the Kconfig options. A minimal set
of options were removed so that it would be easier to work through the
plumbing of the build system.
It should be noted that the host system must provide access to the
device tree compiler (DTC). The DTC can usually be installed on host
systems through distribution packages or by downloading and compiling
from https://git.kernel.org/pub/scm/utils/dtc/dtc.git
This patch also requires the Python yaml package.
This change implements parts of each of the following Jira:
ZEP-1304
ZEP-1305
ZEP-1306
ZEP-1307
ZEP-1589
Change-Id: If1403801e19d9d85031401b55308935dadf8c9d8
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The entry point specified in the elf file should always point to
executable code, and not to the interrupt vector table. Pointing to the
vector table as the entry point in the elf file presents problems with
running the kernel against a debugger as the debugger starts the program
counter at the top of the interrupt vector table.
Change-Id: I76051f6e99a44bab72936670bead5fb8191a6ec7
Signed-off-by: Tim Nordell <tim.nordell@nimbelink.com>
This is a zero-copy networking implementation of Ethernet driver.
Limitations:
- one shot PHY setup, no support for PHY disconnect/reconnect
- no support for devices with DCache enabled due to missing
non-cacheable RAM regions in Zephyr.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1492
Change-Id: Ib944f91193efbd12c1142b0bcf1f635388bf1b87
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added basic USART driver for Atmel SAM MCU family. USART is a very
comprehensive module, currently only basic features sufficient to
support printf functionality are implemented by this driver.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ia9710e4069243fb6c30de45953dfc1fe1266b63a
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Added common, internal, always available SAM HAL drivers: pmc, gpio.
Note: these drivers are meant to be used by other SAM drivers, not by
a user space program directly.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: I00cca358f27790dc94cf79f840584b85ff5191f6
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Added support for early SoC configuration which does not belong
conceptually to system initialization. ERASE, JTAG TDI pins are
currently configured here.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Id51adddb4c7cce22907af214461d75db83df129a
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added support for Atmel SAM E70 (Cortex-M7) MCU:
- Kconfig files
- device start-up code
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ide4fd5dadd94897303090a6507b8d048773b645e
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
As cpu_idle.S is the only bit of code that is using the SCB asm defines,
so to allow us to remove scb.h in the future lets move the defines that
are used just into cpu_idle.S
Jira: ZEP-1568
Change-Id: I3c3a6f145ec4c1a43f076d079d5fe1694c255b78
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A number of SoCs clear out the Mem/Bus/Usage and Hard Fault exceptions
during init. Lets refactor that into a common function so we don't have
to keep duplicating it over and over.
Change-Id: Ida908a9092db37447abcf3c9872f36937982f729
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch fixes the UART4 base address on the ARM MPS2 platform.
Change-Id: I14bf2a4dc2378d4b2c4295a75cd68c6c895fbd60
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Kill of nvic.h and use either CMSIS helper functions for NVIC or direct
NVIC register access via CMSIS for IRQ handling code.
Jira: ZEP-1568
Change-Id: If21910b9293121efe85c3c9076a1c2b475ef91ef
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace _ScbExcPrioSet with calls to NVIC_SetPriority as it handles both
interrupt and exception priorities. We don't need to shift around the
priority values for NVIC_SetPriority.
Jira: ZEP-1568
Change-Id: Iccd68733c3f7faa82b7ccb17200eef328090b6da
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the configuration parametes required to enable CMSDK
(Cortex-M System Design Kit) Drivers at MPS2 soc level.
It provides as well the definitions for the MPS2 System Control
registers.
Change-Id: I06181dcfeb4fb887425b85ec9a99c268c857a34e
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Adds initial support for the kw41z SoC. This is the first SoC in the
Kinetis W (wireless connectivity) series added to Zephyr. The kw41z
integrates a 2.4 GHz radio transceiver, BLE link layer hardware, and an
802.15.4 packet processor with an ARM Cortex M0+. It has 512 KB flash,
128 KB SRAM, and can run the system clock at up to 48 MHz.
This SoC currently has mcux shim drivers for lpuart (serial), gpio,
pinmux, i2c, and flash.
Jira: ZEP-1389
Change-Id: I8cff6d203867ba3ace7e05c36441dc8f3cbca8d8
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the flash security section so it makes sense for other Kinetis
devices, not just k64. In Kinetis reference manuals, this section is
referred to as the 'flash configuration field'.
Change-Id: I2b7c7cc1ec2541419d77878d367d96c9ceb7a0cf
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux lpuart driver to adapt it to the Zephyr
serial interface.
NXP has multiple uart hardware blocks that implement different features
and have different register maps. The k64 has a uart block called
'uart', while the kw41 has a uart block called 'lpuart' (low power
uart). The MCUXpresso SDK provides separate drivers for each type of
uart block but with similar software interfaces. As a result, there are
also separate shim drivers in Zephyr. There is a 1:1:1 relationship
between hardware block, mcux driver, and mcux shim driver.
Because we now have two mcux shim drivers for the uart interface, a new
naming convention is created:
<interface>_mcux_<hw block>
Where <interface> is the name of the Zephyr interface, in this case
'uart'. This convention is not new.
<hw block> is the name of the NXP hardware block, in this case 'lpuart'.
This is the new part, and distinguishes different hardware blocks
for the same interface.
Change-Id: I3a80b9bffa116bbb2b02ee950d4bdd79a19a4edc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Nordic Semiconductor's Software Development Kit's HAL layer
provides a set of low-level header and sourcefiles that give access
to the different hardware peripherals of Nordic ICs.
This patch includes the new files in the build and refactors the Kconfig
and Kbuild files in ext/hal/nordic to acommodate for the presence of the
new HAL layer.
Change-Id: Ie8e1a4c9fcc7e9058a9d16a2692ef1789603aa53
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The STM32 GPIO driver extended the generic GPIO driver interace with
the concept of OPEN_DRAIN. There is previous discussion about
representing such concepts in the GPIO interface in a more general
fashion here:
https://lists.zephyrproject.org/archives/list/devel@lists.zephyrproject.org/thread/6DCFUAKCOOOBHUO3ZK45ES6IQXOEOFWN/
The DRIVE STRENGTH interface supports the concepts of OPEN DRAIN and
other variants supports by other vendors hardware.
Adjust the STM32 GPIO driver to use the DRIVE STRENGTH interface. A
following patch will address the simplication of gpio.h
Change-Id: I56b0792ec2b21f1adc673dff019288dc8573d005
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This avoids asm files from having to explicitly define the _ASMLANGUAGE
symbol themselves.
Change-Id: I71f5a169f75d7443a58a0365a41c55b20dae3029
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
They are not part of the API, so rename from K_<state> to
_THREAD_<state>.
Change-Id: Iaebb7d3083b80b9769bee5616e0f96ed2abc5c56
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Replace _scs_relocate_vector_table with direct CMSIS register access and
use of __ISB/__DSB routinues. We also cleanup the code a little bit to
just have one implentation of relocate_vector_table() on ARMv7-M.
Jira: ZEP-1568
Change-Id: I088c30e680a7ba198c1527a5822114b70f10c510
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
CMSIS provides a complete implentation for reboot, we can utilize it
directly and reduce zephyr specific code.
Jira: ZEP-1568
Change-Id: Ia9d1abd5c1e02e724423b94867ea452bc806ef79
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As a first step towards removing the custom ARM Cortex-M Core code
present in Zephyr in benefit of using CMSIS, this change replaces
the use of the custom core code with CMSIS macros in
enable_floating_point().
Jira: ZEP-1568
Change-id: I544a712bf169358c826a3b2acd032c6b30b2801b
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Support using CMSIS defines and functions, we either pull the expect
defines/enum from the SoC HAL layers via <soc.h> for the SoC or we
provide a default set based on __NVIC_PRIO_BITS is defined.
We provide defaults in the case for:
IRQn_Type enum
*_REV define (set to 0)
__MPU_PRESENT define (set to 0 - no MPU)
__NVIC_PRIO_BITS define (set to CONFIG_NUM_IRQ_PRIO_BITS)
__Vendor_SysTickConfig (set to 0 - standard SysTick)
Jira: ZEP-1568
Change-Id: Ibc203de79f4697b14849b69c0e8c5c43677b5c6e
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In preperation for removing the scb/scs layers and using CMSIS directly
lets remove all the _Scb* and _Scs* functions that are not currently
used.
Jira: ZEP-1568
Change-Id: If4641fb9a6de616b4b8793d4678aaaed48e794bc
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ARM's Cortex-M Prototyping System (or MPS2) [1] is a board containing
devices such as RAM, ethernet and display, and at its heart there is an
FPGA which can be programmed with various 'SoCs' which implement the
CPU, SRAM, UARTs, SPI, DMA, etc. There are also software simulations of
systems based on this hardware which are part of ARM's Fixed Virtual
Platforms (FVPs).
All of the above could be regarded SoCs in the same series so we will
treat them as such in Zephyr.
In this initial patch we add SoC support for the public FPGA image
which implements a Cortex-M3 CPU, and includes definitions to support
use of the UARTs on this.
ARM's documentation for MPS2 images are titled 'Application Note ANnnn'
where the number nnn is different for each 'SoC'. E.g. Application Note
AN385 is for "ARM Cortex-M3 SMM on V2M-MPS2" [2]. The files ARM supply
for programming the board firmware also make extensive use of the ANnnn
nomenclature, so we will use this for the SoC name in Zephyr. E.g. the
Cortex-M3 SoC will be called 'mps2_an385'. Note, it is not possible to
use the CPU type (e.g. M3) for the name as there are multiple FPGA
images for some CPU types (e.g. there are three Cortex M7 images
with differing FPU and MPU support).
[1] https://www.arm.com/products/tools/development-boards/versatile-express/cortex-m-prototyping-system.php
[2] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dai0385c/index.html
Change-Id: Ice54f2d2cde7669582337f256c878526139daedd
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Now that we have a more generic mcux spi driver that can be used across
multiple Kinetis SoCs, remove the specific k64 spi driver.
Jira: ZEP-1374
Change-Id: Ifc324374f305837f5e3d2cfd7ad30d3608865b5b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the timers IRQ map to the ARM Beetle SoC platform.
Jira: ZEP-1300
Change-Id: If38a197210f71ae90c7ee6274395f064116faf72
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
On other targets, CONFIG_TEXT_SECTION_OFFSET allows the entire image to
be moved in memory to allow space for some type of header. The Mynewt
project bootloader prepends a small header, and this config needs to be
supported for this to work.
The specific alignment requirements of the vector table are chip
specific, and generally will be a power of two larger than the size of
the vector table.
Change-Id: I631a42ff64fb8ab86bd177659f2eac5208527653
Signed-off-by: David Brown <david.brown@linaro.org>
Now that we have a more generic mcux serial driver, remove the uart_k20
driver.
Jira: ZEP-719
Change-Id: I51a3237454140feabbfe18ac2c8ee451e572c7be
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stop using the specific uart_k20 driver by default and start using the
more generic mcux uart driver instead.
Jira: ZEP-719
Change-Id: I7b107ea7118887591362159283ebb5413b45595a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Implementation includes adding some defines in the pinmux,
adjusting gpio driver to specific defines for STM32F3X family,
adding specific functionality in the F3X SoC definition.
Change-Id: I465c66eb93e7afb43166c4585c852e284b0d6e67
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
SOC_FLASH_NRF5 is compatible with any nrf5 device, so enable the driver
by default if CONFIG_FLASH is also enabled.
Change-Id: I6ddf7cc41bb28071f682e78661b184a8e2ee7aa9
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
It is called before early SoC initialization, so remove the duplicated
code from other boards and just set it by default when using XIP.
This can later be used when adding bootloader support, as an
additional option could be created to move the VTOR offset to a
different address.
Change-Id: Ia1f5d9a066de61858ee287215cefdd58596b6b1c
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The mcux pinmux driver enables the port clocks, so the soc init no
longer needs to enable them. Also removes some soc defines that were
used only by the legacy k64 pinmux driver.
Change-Id: I63174bef4024b5a09a73f941cea0aec691c759d3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we have a more generic mcux gpio driver that can be used across
multiple Kinetis SoCs, remove the specific k64 gpio driver.
Jira: ZEP-1394
Change-Id: I177f96a75e441b70c523e74e99f1b7a54eac6b0e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stop using the specific k64 gpio driver by default and start using the
more generic mcux gpio driver instead.
Jira: ZEP-1394
Change-Id: I54ec9b62cc8790b8973efc34fa36d17da523971e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the uart console pins from the k64 soc init to the frdm_k64f and
hexiwear_k64 board pinmux tables. Not having these pins in the board
pinmux tables led one to believe that no pins in PORTB were being used
on the hexiwear_k64 board, and thus the port was incorrectly disabled by
default.
Also fixes PORTB to be enabled by default if the uart console is used.
Change-Id: Ide6b7b34dfba8a75a02a8f2bf37cce843afb92f1
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch provides initial support for the SoC STM32F107. This SoC
belongs to the Connectivity Line devices.
Connectivity line family incorporates up to 14 communication
interfaces such as: 2 x I2C, 5 x USART, 3 x SPI, 2 x CAN, USB 2.0,
10/100 Ethernet MAC.
Change-Id: I5cb2c458bce9ec1558b4168e87a7003ad9f606a5
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all the ksdk/mcux shim drivers use the config HAS_MCUX, we can
remove the config HAS_KSDK.
Change-Id: I94b7db41efae10c9234681aeb57f94e67a33c262
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the ksdk random generator shim driver to mcux.
Change-Id: I8bc376937fed3024c809782139a0a72c7332f89a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The ksdk pinmux dev driver was previously merged into the regular ksdk
pinmux driver, and the config PINMUX_DEV_KSDK was removed. Two
references were inadvertantly left behind, so remove them now.
Change-Id: I77394be5459d55a9f16e7bd2b3c9d688c4605b4f
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
stm32f411re SoC could run at system clock above 84MHz.
This was not taken into account in __setup_flash function which configure
flash latency depending on system clock. This is now corrected.
Assert added to ease error detection.
Change-Id: I49b92256d611ef464171fb1d8812a4c4d3c27ab8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Previously, CC3200 drivers had two options to use the peripheral
driver library APIs:
1) Build driverlib SDK files in Zephyr, in ext/hal/ti/cc3200/*
2) Link directly with the driverlib.a, from an externally installed
TI CC3200 SDK.
A new option is added to replace option 2), and is now the default:
3) Use the driverlib functions already provided in ROM.
This enables a savings in code size, which will depend on the
types of device drivers configured and the number of SDK
APIs actually used.
A rom_report build of the shell sample application showed
a savings of about 2kb in code space using this new config option.
Change-Id: Ie1ede6f7aacd23db20f5292e776f1dfeab5c7fe0
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The cortex-m7 is an implementation of armv7-m. Adjust the Kconfig
support for cortex-m7 to reflect this and drop the unnecessary,
explicit, conditional compilation.
Change-Id: I6ec20e69c8c83c5a80b1f714506f7f9e295b15d5
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Precursor patches have arranged that conditional compilation hanging
on CONFIG_CPU_CORTEX_M3_M4 provides support for ARMv7-M, rename the
config variable to reflect this.
Change-Id: Ifa56e3c1c04505d061b2af3aec9d8b9e55b5853d
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Precursor patches have arranged all conditional compilation hanging on
CONFIG_CPU_CORTEX_M0_M0PLUS such that it actually represents support
for ARM ARMv6-M, rename the config variable to reflect this.
Change-Id: I553fcf3e606b350a9e823df31bac96636be1504f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The ARM code base provides for three mutually exclusive ARM
architecture related conditional compilation choices. M0_M0PLUS,
M3_M4 and M7. Throughout the code base we have conditional
compilation gated around these three choices. Adjust the form of this
conditional compilation to adopt a uniform structure. The uniform
structure always selects code based on the definition of an
appropriate config option rather the the absence of a definition.
Removing the extensive use of #else ensures that when support for
other ARM architecture versions is added we get hard compilation
failures rather than attempting to compile inappropriate code for the
added architecture with unexpected runtime consequences.
Adopting this uniform structure makes it straight forward to replace
the adhoc CPU_CORTEX_M3_M4 and CPU_CORTEX_M0_M0PLUS configuration
variables with ones that directly represent the actual underlying ARM
architectures we provide support for. This change also paves the way
for folding adhoc conditional compilation related to CPU_CORTEX_M7
directly in support for ARMv7-M.
This change is mechanical in nature involving two transforms:
1)
#if !defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
is transformed to:
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
#elif defined(CONFIG_CPU_CORTEX_M3_M4) || defined(CONFIG_CPU_CORTEX_M7)
...
2)
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
#else
...
#endif
is transformed to:
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
#elif defined(CONFIG_CPU_CORTEX_M3_M4) || defined(CONFIG_CPU_CORTEX_M7)
...
#else
#error Unknown ARM architecture
#endif
Change-Id: I7229029b174da3a8b3c6fb2eec63d776f1d11e24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Adjust the layout of various ARM assember files to conform to the norm
used in the majority of files.
Change-Id: Ia5007628be5ad36ef587946861c6ea90a8062585
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The 16k RAM nRF51 variants pose a challenge to get applications to fit
within the available memory. Make the default ISR stack size smaller
than the previous 2k default, but big enough to run fully functional
Bluetooth controller and host stacks.
Change-Id: Ie7c5bb21a3ba620d283e6228a2482d280f85119d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
On the nRF5x platforms we need always need the NRF_RTC_TIMER and it
depends on the CLOCK_CONTROL_NRF5. So enable all of these always.
Fixes issues if one tries to build nRF5x platforms w/o CONFIG_BLUETOOTH.
Change-Id: I0f9af785e785f37ec289a935ddf70ee6dec08cd4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These two fields in the thread structure control the preemptibility of a
thread.
sched_locked is decremented when the scheduler gets locked, which means
that the scheduler is locked for values 0xff to 0x01, since it can be
locked recursively. A thread is coop if its priority is negative, thus
if the prio field value is 0x80 to 0xff when looked at as an unsigned
value.
By putting them end-to-end, this means that a thread is non-preemptible
if the bundled value is greater than or equal to 0x0080. This is the
only thing the interrupt exit code has to check to decide to try a
reschedule or not.
Change-Id: I902d36c14859d0d7a951a6aa1bea164613821aca
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Some thread fields were 32-bit wide, when they are not even close to
using that full range of values. They are instead changed to 8-bit fields.
- prio can fit in one byte, limiting the priorities range to -128 to 127
- recursive scheduler locking can be limited to 255; a rollover results
most probably from a logic error
- flags are split into execution flags and thread states; 8 bits is
enough for each of them currently, with at worst two states and four
flags to spare (on x86, on other archs, there are six flags to spare)
Doing this saves 8 bytes per stack. It also sets up an incoming
enhancement when checking if the current thread is preemptible on
interrupt exit.
Change-Id: Ieb5321a5b99f99173b0605dd4a193c3bc7ddabf4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This will allow for an enhancement when checking if the thread is
preemptible when exiting an interrupt.
Change-Id: If93ccd1916eacb5e02a4d15b259fb74f9800d6f4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The Cortex-M0(+) and in general processors that support only the ARMv6-M
instruction set have a reduced set of registers and fields compared to
the ARMv7-M compliant processors.
This change goes through all core registers and disables or removes
everything that is not part of the ARMv6-M architecture when compiling
for Cortex-M0.
Jira: ZEP-1497
Change-id: I13e2637bb730e69d02f2a5ee687038dc69ad28a8
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
replace include <nanokernel.h> with <kernel.h> everywhere and also fix
any remaining mentions of nanokernel.
Keep the legacy samples/tests as is.
Change-Id: Iac48447bd191e83f21a719c69dc26233216d08dc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Obsolete, replaced by _set_thread_return_value().
Change-Id: I23e9cfc07e43542f0965817edc3552d456fd2ef3
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Previously, UART clock enable was done in pinmux init.
This is now moved into soc initialization, along with other
power related initialization routines.
Change-Id: I1f9464655ad966e9caac2d238006f12a06b202ab
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
To make way for the upcoming blinky and GPIO support for nRF5x-based
boards, this change addresses the hardcoded dependencies in Kconfig
default configurations of the different boards, moving the common option
defaults to the SoC default configuration itself.
Change-Id: I8db0750311ad5a12b76237b39438376f20f6f496
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/basic/blinky
- samples/basic/disco
- samples/basic/button
All 4 GPIO ports are supported.
Change-Id: If8599a23c1d56cfd678a6e2e5339f7e093c6061a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The new Nordic nRF52840 IC is the latest member of the nRF52 family.
It supports the following features among others:
* Cortex-M4F core at 64MHz
* 1024KB of flash and 256KB of RAM
* Bluetooth 5-ready and 802.15.4 compatible radio
* USB device support
* NFC Tag support
* Quad-SPI
* Hardware accelerated crypto engine
http://www.nordicsemi.com/eng/Products/nRF52840
JIRA: ZEP-1418
Change-Id: I677c787bb33d02695e057d5dced7e3455b9f6c50
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In preparation for the upcoming nRF52840 support, this patch refactors
the nRF52 series support code to allow for future members of the IC
family to be added, while keeping everything that is common together.
JIRA: ZEP-1418
Change-Id: I4200064ca888d72ba0b8629ce94e4ea6384099ad
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Also remove mentions of unified kernel in various places in the kernel,
samples and documentation.
Change-Id: Ice43bc73badbe7e14bae40fd6f2a302f6528a77d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Also remove some old cflags referencing directories that do not exist
anymore.
Also replace references to legacy APIs in doxygen documentation of
various functions.
Change-Id: I8fce3d1fe0f4defc44e6eb0ae09a4863e33a39db
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
That module is not used anymore: it was introduced pre-Zephyr to add
some kind of awareness when debugging ARM Cortex-M3 code with GDB but
was never really used by anyone. It has bitrotted, and with the recent
move of the tTCS and tNANO data structures to common _kernel and
k_thread, it does not even compile anymore.
Jira: ZEP-1284, ZEP-951
Change-Id: Ic9afed00f4229324fe5d2aa97dc6f1c935953244
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The K64F board has the ENET ethernet driver. Behavior consistently
with other driver selection logic and default the KSDK ethernet driver
on if ETHERNET drivers are enabled.
Change-Id: I2fbed7fdef22d75cf163b61b3e0530ce00d988f0
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
And also remove now obsolete ARCH_HAS_TASK_ABORT.
ARC does not need the options either.
Change-Id: Ie52d63178a367ce12b911dacfe2d389f4f75ed2d
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
- does not pull in printk(), for potential footprint gain
- does not pull in k_thread_abort(), for single-threaded systems
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Change-Id: Ibc6a198b81a6cd73117d1e85aa05b92a4501a34d
Some kernel operations, like scheduler locking can be optmized out,
since coop threads lock the scheduler by their very nature. Also, the
interrupt exit path for all architecture does not have to do any
rescheduling, again by the nature of non-preemptible threads.
Change-Id: I270e926df3ce46e11d77270330f2f4b463971763
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
nano_cpu_idle/nano_cpu_atomic_idle were not ported to the unified
kernel, and only the old APIs were available. There was no real impact
since, in the unified kernel, only the idle thread should really be
doing power management. However, with a single-threaded kernel, these
functions can be useful again.
The kernel internals now make use of these APIs instead of the legacy
ones.
Change-Id: Ie8a6396ba378d3ddda27b8dd32fa4711bf53eb36
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The way the ready thread cache was implemented caused it to not always
be "hot", i.e. there could be some misses, which happened when the
cached thread was taken out of the ready queue. When that happened, it
was not replaced immediately, since doing so could mean that the
replacement might not run because the flow could be interrupted and
another thread could take its place. This was the more conservative
approach that insured that moving a thread to the cache would never be
wasted.
However, this caused two problems:
1. The cache could not be refilled until another thread context-switched
in, since there was no thread in the cache to compare priorities
against.
2. Interrupt exit code would always have to call into C to find what
thread to run when the current thread was not coop and did not have the
scheduler locked. Furthermore, it was possible for this code path to
encounter a cold cache and then it had to find out what thread to run
the long way.
To fix this, filling the cache is now more aggressive, i.e. the next
thread to put in the cache is found even in the case the current cached
thread is context-switched out. This ensures the interrupt exit code is
much faster on the slow path. In addition, since finding the next thread
to run is now always "get it from the cache", which is a simple fetch
from memory (_kernel.ready_q.cache), there is no need to call the more
complex C code.
On the ARM FRDM K64F board, this improvement is seen:
Before:
1- Measure time to switch from ISR back to interrupted task
switching time is 215 tcs = 1791 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 315 tcs = 2625 nsec
After:
1- Measure time to switch from ISR back to interrupted task
switching time is 130 tcs = 1083 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 225 tcs = 1875 nsec
These are the most dramatic improvements, but most of the numbers
generated by the latency_measure test are improved.
Fixes ZEP-1401.
Change-Id: I2eaac147048b1ec71a93bd0a285e743a39533973
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The Cortex-M3/4 kernel was reserving priorities 0 and 1 for itself, but
was not registering any exception on priority 0. Only reserve priority 0
and use it for SVC and fault exceptions instead of priority 1.
Change-Id: Iff2405e27fd4bed4e49ab90ec2ae984f2c0a83a6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Cortex-M0/M0+ do not have other faults than the hard fault at priority
-1, so they do not need to reserve a priority to allow exceptions to
trigger during handling of ISRs.
Change-Id: I479e439f7bcac70b4b2b787bcd744a4c65437e80
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This allows using it in _EXC_PRIO() instead of hardcoding 2 and 3.
Change-Id: I3549be54602643e06823ba63beb6a6992f39f776
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use it to flag which CPUs can do zero latency interrupts, which depend
on being able to lock up to a specific interrupt priority.
Change-Id: I09f71366ea1d05486e38c513a09abc270884879f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Add a "memory" clobber to inline asm SVC call to ensure the compiler
does not reorder the instruction relative to other memory accesses.
Issue found by inspect the source code. There is no evidence to
suggest that this bug will manifest for any current ARM target using a
current compiler.
Change-Id: I32b1e5ede02a6dbea02bb8f98729fff1cca1ef2a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Basic interrupt driven driver for the nRF5 onboard temperature sensor.
Change-Id: Id0ac303293b8e8b8285b19bcda31284ee6617105
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Stop using the specific k64 pinmux driver by default and start using the
more generic ksdk pinmux driver instead.
Jira: ZEP-1393
Change-Id: Id65b59518c386e6ba33cfa5c4c5bd541664d2b41
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Following pinmux update for PWM support,
update soc to support this new configuration.
Change-Id: I1126e347ab1ab6b2d830993e548de8f32fa2f8f9
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the boot time Power Management configuration for Beetle
on Zephyr. In particular it defines the states of the peripherals during
sleep and deep sleep and the allowed wakeup sources.
Jira: ZEP-1300
Change-Id: Iad9c0f851771ea60d94bbe5420b7b3ee0743b77e
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add one pin configuration for I2C1 of the STM32L4 series.
Change-Id: Id05d916f2a1126ca439aebcddd8dc9c91015f6fe
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the pin configuration of the USARTs.
Change-Id: Idf7a18b6eab95c61870ad4850c9eafb1fdcab03d
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the clock driver for the STM32L4 series.
Change-Id: Icdf79061f163d8d00187b382d1564422fb875c5b
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the initial SoC support for the STM32L4XX family. The code was
tested on STM32L476RG, but should work on any STM32L4XX currently
available.
This implementation was inspired by the stm32f1x implementation.
Change-Id: Id6670bce0c423617284e8467a9c461531f948e0f
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Due to new serial driver implementation based on STM32Cube we can
remove the USARTX_ADDR defines as they aren't ended anymore
Change-Id: Ia9f9b0a2a63280c0221c789a53ff7338bda17dfb
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Due to new serial driver implementation based on STM32Cube we can
remove the USARTX_ADDR defines as they aren't ended anymore
Change-Id: Icd5b7995429025c5b54b1a04ca6abb9649ab31c8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube based implementation allows single driver file for
all stm32 based SoCs.
By maximizing code reuse, use of STM32Cube eases new SoCs
porting into Zephyr and provides better maintanability and
maturity.
Change-Id: Ief4b723add3dfc8b2a839683559c5a4c5d5eb837
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch fixes the unused parameter warning found at the
arch/arm/core/fault.c and arch/arm/soc/st_stm32/stm32f1/soc_gpio.c
files.
Change-Id: I5b3013c1514cff30f4e98feb31169fb28546c534
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Initializing the interrupt stack before initializing (turning off) the
watchdog on the FRDM board pushed the initialization of the watchdog too
late, causing it to fire and reset the board. The board would be kept in
a reboot loop.
Move the initialization of the watchdog earlier: this runs on the main
stack now, instead of the interrupt stack, the same stack the interrupt
stack initalization code runs on.
Change-Id: Ic0006f4f4f4090393571d8355a80dc9390c9fbc6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The nRF5x series SoCs do not implement systick, hence we disable
CORTEX_M_SYSTICK.
Instead, use nRF SoC Series NRF_RTC1 for system clock interfaces.
The kernel system clock interface is implemented using the low
power real time counter NRF_RTC1. NRF_RTC0 is used by the BLE
controller.
In addition, cleanup nRF5x series defconfig to be consistent.
Jira: ZEP-742
Jira: ZEP-1308
Jira: ZEP-1315
Change-id: I0f6cc1836fe0820a65f2cbb02cf5ae7e9eb92e1d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Make the systick feature optional that can be selected by the SoC.
Change-Id: I4a405640b84daecc17fc1882743d3cafb78ff861
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
An IRQ would always register as a ZIL interrupt.
Change-Id: If82a85f472a60512745652aacc7e8b7dfacaa268
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Also remove NO_METRIC, which is not referenced anywhere anymore.
Change-Id: Ieaedf075af070a13aa3d975fee9b6b332203bfec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The assembler was passed immediate values that are too large for the
limited Cortex-M0 thumb assembly. Load values in registers instead of
using immediate values.
Change-Id: Ib5541c92dea03e0efb1b88ab91eeb408d151a71b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This patch enables REBOOT when RUNTIME_NMI is selected via defconfig
file. This action is required to prevent compilation errors.
Change-Id: I67c18b2860ac34ba8f96e780737b4857a6063ece
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If CORTEX_M_SYSTICK is not selected, do not reference
_timer_int_handler. SoC will need to define a custom system
clock implementation.
Change-Id: I655f3abf66953e434fef69ed16db2d9c2dcc486e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Zephyr kernel is unable to compile when CONFIG_RUNTIME_NMI is enabled in
defconfig on ARM's architectures.
This patch addresses the following issues:
* In nmi.c _DefaultHandler() is referencing a function
(_ScbSystemReset()) not defined in Zephyr. This has now been replaced
with sys_arch_reboot.
* nmi.h is included in ASM files and due to the usage of "extern" the
compilation ends with an error. Added the directive _ASMLANGUAGE to
prevent the problem.
Jira: ZEP-1319
Change-Id: I7623ca97523cde04e4c6db40dc332d93ca801928
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Move _thread_base initialization to _init_thread_base(), remove mention
of "nano" in timeouts init and move timeout init to _init_thread_base().
Initialize all base fields via the _init_thread_base in semaphore groups
code.
Change-Id: I05b70b06261f4776bda6d67f358190428d4a954a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use the main stack during very early boot so that we can call memset on
the interrupt stack. Initialize the interrupt stack before it is used
for the rest of the pre-kernel initialization.
Change-Id: I6fcc9a08678afdb82e83465cda1c7a2a8c849c9b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The ARM Cortex-M early boot was using a custom stack at the end of the
SRAM instead of the interrupt stack. This works as long as no static
data that needs a known initial value occupies that stack space. This
has probably not been an issue because the .noinit section is at the
very end of the image, but it was still wrong to use that region of
memory for that initial stack.
To be able to use the interrupt stack during early boot, the stack has
to be released before an interrupt can happen. Since ARM Cortex-M uses
PendSV as a very low priority exception for context switching, if a
device driver installs and enables an interrupt during the PRE_KERNEL
initialization points, an interrupt could take precedence over PendSV
while the initial dummy thread has not yet been context switched of and
thus released the interrupt stack. To address this, rather than using
_Swap() and thus triggering PendSV, the initialization logic switches to
the main stack and branches to _main() directly instead.
Fixes ZEP-1309
Change-Id: If0b62cc66470b45b601e63826b5b3306e6a25ae9
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Artifact from microkernel, for handling multiple pending tasks on
nanokernel objects.
Change-Id: I3c2959ea2b87f568736384e6534ce8e275f1098f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
PA10 should use *_PA10_UART1_RX
Change-Id: Ifba4d301d049db1d62ea3a63d4d66f75c88a71a6
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Prio should be an int, since values are small integers, not a fixed-size
int32_t. It aligns with the prio parameters of the other APIs.
Stack size should be size_t.
Change-Id: Id29751b86c4ad7a7c2a7ffe446c2a96ae83c77bf
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The bitfield determining the I/O direction already defines the pin
as either input or output, cannot be none or both at the same time
This issue was reported by Coverity
Coverity-CID: 151970
Change-Id: I18d5387139d6834004ba3269c5b54176bdc97ea7
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
There was a possible race condition when setting the return value of a
thread that is pending, from an ISR.
A kernel function causes a thread to pend, with the following series of
steps:
- disable interrupts
- move current thread to wait_q
- call _Swap
Depending if running on M3/4 or M0+, _Swap will either issue a svc #0,
or pend PendSV directly. The same problem exists in both cases.
M3/4:
__svc will:
- enable interrupts
- trigger __pendsv
M0+:
_Swap() will enable interrupts.
__pendsv will:
- save register context including PSP into the thread struct
If an interrupt occurs between interrupts being enabled them and
__pendsv saving PSP, and the ISR sets the pending thread's return value,
this will happen:
- sees the thread in a wait_q
- removes it
- makes it ready
- calls _set_thread_return_value
- _set_thread_return_value looks at the thread's saved PSP to poke
the value
In this scenario, PSP hasn't yet been updated by __pendsv so it's a
stale value from the previous context switch, resulting in unpredictable
word on the stack getting set to the return value.
There is no way to fix this issue and still have the return value being
delivered directly in the pending thread's exception stack frame, in the
M0+ case. There will always be a window between the unlocking of
interrupts and PendSV being handled. On M3/4, it could be possible with
the mix of SVC and PendSV, since the exception stack frame is created in
the __svc handler. However, because we want to keep the two
implementations as close as possible, and there were talks of moving
M3/4 to using PendSV only, to save an exception, the approach taken
solves both cases.
The approach taken is similar to the ARC and Nios2 ports, where
there is a field in the thread structure that holds the return value.
_Swap() then loads r0/a1 with that value just before returning.
Fixes ZEP-1289.
Change-Id: Iee7e06fe3f8ded84aff918fd43408c7f589344d9
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
When a thread dies, at least print the pointer to it, so we can debug
better.
Change-Id: Ief6bbc0c221e2d5271c240a4b73df16413aa5e22
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This reverts commit
"kernel/arm: add comment about _is_next_thread_current"
and fixes the interrupt locking issue.
The comment would have been right if only reads were done the ready
queue, but that is not the case. It turns out that the comment was written
ignoring the fact that _is_next_thread_current() updates the next thread
cache when fetching the next thread.
Change-Id: I21c9230f85f4f87a6bbf14fd4a9eb7e19b59f8c5
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Though Cortex-M4 could optionally have a floating point unit,
the MCU in the cc3200 in fact does not have an FPU.
Enabling CPU_HAS_FPU caused applications built with CONFIG_FLOAT=y
to crash during an early call to enable_floating_point().
This patch was validated by running microPython, which is one
such application.
Change-Id: I8bfd42c456524e152cbbb983001d9540d93fbe98
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Normally, _is_next_thread_current() must be called with interrupts
locked, but the ARM interrupt exit code does not have to do that. Add
explanation why.
Change-Id: Id383b47a055fdd6fbd5afffa52772e92febde98f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
There was a lot of duplication between architectures for the definition
of threads and the "nanokernel" guts. These have been consolidated.
Now, a common file kernel/unified/include/kernel_structs.h holds the
common definitions. Architectures provide two files to complement it:
kernel_arch_data.h and kernel_arch_func.h. The first one contains at
least the struct _thread_arch and struct _kernel_arch data structures,
as well as the struct _callee_saved and struct _caller_saved register
layouts. The second file contains anything that needs what is provided
by the common stuff in kernel_structs.h. Those two files are only meant
to be included in kernel_structs.h in very specific locations.
The thread data structure has been separated into three major parts:
common struct _thread_base and struct k_thread, and arch-specific struct
_thread_arch. The first and third ones are included in the second.
The struct s_NANO data structure has been split into two: common struct
_kernel and arch-specific struct _kernel_arch. The latter is included in
the former.
Offsets files have also changed: nano_offsets.h has been renamed
kernel_offsets.h and is still included by the arch-specific offsets.c.
Also, since the thread and kernel data structures are now made of
sub-structures, offsets have to be added to make up the full offset.
Some of these additions have been consolidated in shorter symbols,
available from kernel/unified/include/offsets_short.h, which includes an
arch-specific offsets_arch_short.h. Most of the code include
offsets_short.h now instead of offsets.h.
Change-Id: I084645cb7e6db8db69aeaaf162963fe157045d5a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The unified kernel is now the only supported kernel, so this
option is unnessary. Eliminating this option also enables
the removal of some legacy code that is no longer required.
Change-Id: Ibfc339d643c8de16a2ed2009c9b468848b8b4972
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Add SoC support for ARM Beetle platform.
Beetle is an ARM Cortex-M3 based SoC used on ARM V2M Beetle Boards.
https://www.arm.com/products/tools/development-boards/versatile-express/beetle_iot_evaluation_platform.php
This patch contains:
* The base SoC platform.
* The clock_init functionality.
* The system wide pin definitions.
* The configuarion for the drivers at SoC level (IRQs, PINs and
Base Addr).
Jira: ZEP-1245
Change-Id: If15675935890711983e5ce37d49732b0462c3ec7
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Verify the thread priorities are within the bounds when starting a new
thread and when changing the priority of a thread.
Change-Id: I007b3b249e4b80235b6439cbee44cad2f31973bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Symbols now use the K_ prefix which is now standard for the
unified kernel. Legacy support for these symbols is retained
to allow existing applications to build successfully.
Change-Id: I3ff12c96f729b535eecc940502892cbaa52526b6
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
This KSDK flash shim driver supports the device in the FRDM K64F
platform (enabled with this commit).
WARNING: the driver disables the system interrupts for potentially
long periods of time. This is required to avoid Read-While-Write
issues since most platforms run in XIP mode.
For more detailed information see the link below:
http://cache.freescale.com/files/32bit/doc/app_note/AN4695.pdf
Change-Id: I70f8d09080251033ce2f45be0c2eb95c19fded08
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
The uart_k20 serial driver incorrectly assumed that all instances of the
UART peripheral are driven by the system clock, when actually some
instances are driven by the bus clock (which usually runs at half the
system clock). This caused incorrect baud rate calculations for UART
instances driven by the bus clock (UART2-4).
Change-Id: I38041781cdee146912bb5167e7c71d6416b966b5
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This change is required to support unified kernel.
Change-Id: I47bd644239eb3e624c7a5cb456eedad5aca79e8e
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The unified kernel expect the default return value from a _Swap() call
to be set to -EAGAIN by the architecture code. Cortex-M3/M4 does this in
the SVC call handler, and it was missing from the Cortex-M0/M0+ before
pending PendSV.
Change-Id: I3316901186ab409f49043eb4f1972c4b0dd9a4a2
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/hello_world
- samples/philosophers
- samples/drivers/uart
- samples/shell
UARTA0 is currently supported.
Change-Id: I85727c622d4d42183cc9f2f8b43d653e245dd17e
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Initial support is for the CC3200 SoC, comprising a network coprocessor
and Cortex-M4 MPU.
This leverages the CC3200 SDK driver peripheral library, installed
separately, or built from ext/hal/.
Jira: ZEP-1109
Change-Id: I508afc8596c165b309a4ec641c39abadc779eea3
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The k64 SoC has multiple instances of many peripherals, but which
instances can actually be used depends upon the board design and pinmux
configuration.
Move all instance-specific default driver configurations from the SoC to
the boards (frdm_k64f and hexiwear_k64). Default driver selection
remains in the SoC (e.g., enable the KSDK I2C driver when I2C is
enabled).
This paves the way to support different driver defaults for the
frdm_k64f and hexiwear_k64 boards, but it does not yet change any of the
default values; it only changes where the default values get set.
Change-Id: Id9ed898762eb400ecefeac91ae4dce66da05622d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds standard prefix to symbolic option that flags a thread
as essential to system operation.
Change-Id: Ia904a81ce343fdd1cd44caaaeae641d822777f9b
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Enable HAS_CUBE config flag on stm32f4 family soc.h is updated to
include minimum include files from ext/hal/stm23cube
Change-Id: I35a8c33aab777167ee7029edc1b7a4f6d21fccd8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Create HAS_CUBE config flag to control activation of STM32Cube support.
Generate fitting compilation options for STM32Cube in
/ext/hal/stm32cube/Makefile soc.h is updated to include minimum include
files from ext/hal/stm23cube
Change-Id: If58ce0a4fdb7fbf5f171dfe5f1f8eb75126a8313
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In ST CMSIS files, FLASH_BASE does not mean base address of FLASH register
Instead FLASH_R_BASE is used.
stm32f1 clock control driver is updated to be compatible with this naming.
Change-Id: Ic4fb49c60c392e15fd12c69266baf4c686bd343b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube uses SoC defines made to reflect HW heterogeneity that
should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f401re following define is used:
*STM32F401xE
Which means:
*Same SW could be used on STM32F401RE and STM32F401CE:
same CONFIG_SOC could be used
*Different SW should be used on STMF401RE and STM32F401RC:
different CONFIG_SOC should be used
This change focuses on stm32f4xx series.
Change-Id: I56ff4d1815d09747cf722385532eb2dcbdf37b44
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube uses SoC defines made to reflect HW heterogeneity
that should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f103rb following define is used:
*STM32F103xB
Which means:
*Same SW could be used on STM32F103RB and STM32F103VB:
same CONFIG_SOC could be used
*Different SW should be used on STMF103RB and STM32F103R4:
different CONFIG_SOC should be used
This change focuses on stm32f1xx series.
Change-Id: I5ecfaa52952d04421b27b5e74fb71b4fc108b662
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move common config options one level up to try to simplify the per-board
defconfig
Change-Id: I3d80fa494050634d0f877af2015b01b85df20d1d
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the STM32F401 chip on the board
Change-Id: I96c0799f3658ecea096fa5971bce9faf21919ee1
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F401 allows for upto 16 alternate functions on each pin.
Change-Id: Ib1c14fd31abaa2b05a5ab0f7bd1b4a4748f10f84
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements MCU-specific GPIO input interrupt integration. Added
definition of System configuration controller as well as its needed by
the GPIO code.
The SYSCFG controller is used for system-specific configuration such as:
- remap the type of memory accessible at address 0x00000000
- manage the external interrupt line connection to GPIOs
- configure the I/O compensation cell
Change-Id: Id2ebfbd1b21e77be76406d1cd6cd5d4989e9e2fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Based on the STM32F10x driver. Removing old code as we need to use the
bus number when dealing with 4 possible peripherals.
Change-Id: Id0263aa008e9b039ff9a00339e5622e289ffdf99
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds support for the STMicroelectronics STM32F4x family in the
STM32 MCU line. Configuration is included for the STM32F401RE MCU.
Acknowledgements to Pawel Wodnicki's earlier submission from February that
was used as a starting point for this port. In the end, we rewrote all of it.
Change-Id: I9797c282ac3c0cc66a63b9d34821de95df537ef6
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
The mk64f12 provides RNGA hardware. Follow the implementation pattern
used by various other driver classes and enable the RANDOM KSDK shim
driver if the RANDOM driver is enabled.
Change-Id: I46bdf16cf1c48937011fb1b0e4c292615efd4c95
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
They were the same, standardize on the lowercase one.
Change-Id: I8bca080e45f3e0970697d4451e468b9081f96f5f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
SOC_TI_LM3S6965 and UART_STELLARIS are platform-specific, remove from
arch/arm/defconfig.
Change-Id: I3b37bc2ddfabb1da4e7538b5ab0e553fb2464584
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
STM32F4 requires the alternative function config to be set, so just
initialize that as part of the gpio configure call.
Change-Id: I33a4a8efec59c5ebe7dc3f3580f0dd2bf7ded7f4
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
The STM32F1 range all have the independent watchdog, enable the driver
by default if CONFIG_WATCHDOG is enabled.
Change-Id: I3869884dc51c56194367b46007c87f6cee699689
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
All M7 features common to M3/M4 are working. New features like Tightly
Coupled Memory (TCM) are not yet supported.
Change-Id: I5f7b292e70843aec415728f24c973bb003014f4b
Jira: ZEP-977
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Existing code wasn't removing a thread from the kernel's list
of active threads if the thread terminated or aborted. (It did
remove it if the delayed starting of a thread was cancelled.)
Change-Id: Icc97917e33765696480d0e9bf31e882ef555d095
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Gets rid of unnecessary THREAD_MONITOR_INIT() macro, to be
consistent with the approach taken by _thread_monitor_exit().
Aligns x86 code with the approach used on other architectures.
Revises the associated comments and removes unnecessary
doxygen tags.
Change-Id: Ied1aebcd476afb82f61862b77264efb8a7dc66c9
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Renames _thread_exit() to _thread_monitoring_exit() to make
its purpose clearer. Revises the associated comments and
removes unnecessary doxygen tags.
Change-Id: I010a328d35d2d79d2a29b9d0b6c02097bb655989
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
The baudrate calculation present in set_baudrate() is
causing the UART to emit inital bytes incorrectly, for a
reason currently unknown, but directly related to the fact
that __aeabi_uldivmod is being invoked.
Since the nRF5x Product Specifications do not provide a
standard formula to calculate baudrates and instead list
a predefined set of divisor values, we opt here to use the
official values and remove the attempt at calculating them
manually.
Change-Id: Ic3ff42ea6d065e9a1d26a5350ce5bf5ad661160a
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Several platforms utilize a ihex image format. Rather than
duplicating the build bits in everyones makefile, pull it into the
toplevel makefile so we all share it.
Change-Id: I9097b06e7e386a69ce6ab4d4e4d56cc776adfec2
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Still missing a working timer driver, as SysTick is not really available
in this SoC series (enabled to avoid build issues, but not used).
Jira: ZEP-784
Change-Id: Ie1c8e6c5e8955ee7f260ce013f4451f9215f3457
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Integrating the IRQ definitions for both nRF51 and nRF52, and defining
the set of IRQ values that are common to both.
Also switch the controller, uart and clock drivers to use the common
header definitions.
Change-Id: Id6816d7a97720896cfe4df83656fb8b1f8fb01fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Not disabling SysTick as it is optional by the spec.
SVC not used as there is no priority-based interrupt masking (only
PendSV is used).
Largely based on a previous work done by Euan Mutch <euan@abelon.com>.
Jira: ZEP-783
Change-Id: I38e29bfcf0624c1aea5f9fd7a74230faa1b59e8b
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Those options are not being used anywhere, so remove them and avoid some
confusion.
Change-Id: Ia3767dbd2432851dfae4b1e996f02ed1b2450505
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Bluetooth controller implementation requires the low power
oscillator for radio time space scheduling and as sleep
clock; the high frequency oscillator as the active clock.
For Nordic Semiconductor's nRF5 Series SoC's select the
NRF Clock peripheral when BLUETOOTH_CONTROLLER is selected
in Kconfig build.
Jira: ZEP-897
Change-id: I6f99e90b3485e757be61e91c749e485dd0cfdaba
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
The driver performs one shot PHY setup. There is no support for PHY
disconnect, reconnect or configuration change. The PHY setup,
implement via KSDK contains polled code that can block the
initialization thread for a few seconds.
There is no statistics collection for either normal operation or error
behaviour.
Origin: Original
Change-Id: Ia0f2e89a61348ed949976070353e823c178fcb24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Build breaks when enabling CONFIG_NEWLIB_LIBC because it has its own
sched.h file.
This is a bad symptom of a greater issue: the build system passes many
'-I<path>' options to the compiler, and that allows including header
files by simply specifying their names (when located somewhere else than
<zephyr>/include/) and can cause clashes when several files in different
locations have the same name, like in this case.
Fixes ZEP-1062.
Change-Id: I81d1d69ee6669a609cd0c420b1b8f870d17dcb67
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Builtin might not be available for ARMv6 (Cortex-M0/M0+) depending on
the toolchain used (not available by Zephyr's SDK GCC), so move the
atomic operations selection to the Cortex-M family Kconfig file.
Change-Id: I20a5a0c5fdd2bcff2d304139f5a7e8502fdb1cb3
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
When adding a thread to the ready queue, it is often known at that time
if the thread added will be the next one to run or not. So, instead of
simply updating the ready queues and the bitmask, also cache what that
thread is, so that when the scheduler is invoked, it can simply fetch it
from there. This is only done if there is a thread in the cache, since
the way the cache is updated is by comparing the priorities of the
thread being added and the cached thread.
When a thread is removed from the ready queue, if it is currently the
cached thread, it is also removed from the cache. The cache is not
updated at this time, since this would be a preemptive fetching that
could be overriden before the newly cached thread would even be
scheduled in.
Finally, when a thread is scheduled in, it now becomes the cached thread
since the fact that it is running means that by definition it was the
next one to run.
Doing this can speed up considerably some context switch times,
especially when a thread is preempted by an interrupt and the same
thread is scheduled when the interrupt exits.
Change-Id: I6dc8391cfca566699bb9b217eafe6bc6a063c8bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The unified kernel calls a function (_get_next_ready_thread) to fetch
the next thread to run: it thus must save caller-saved registers that
are expected to hold a value before calling such function.
The callee-saved registers are available after saving them in the
outgoing thread's stack, so use some of those instead to reduce the
number of registers to save before calling _get_next_ready_thread. Also,
save caller-saved registers in callee-saved registers instead of on the
stack to reduce memory accesses.
This issue did not show up previously, probably because
_get_next_ready_thread did not use the regsiters that had to be saved,
but an upcoming optimization to that function stomps on them.
Change-Id: I27dcededace846e623c3870d907f0d4c464173bf
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Not used anymore as the support for dynamic IRQs was removed by
commit 844e212.
Change-Id: I624bbd777b2dbcbf905cedc61e63cef21e8a0bce
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Move SRAM_BASE_ADDRESS and FLASH_BASE_ADDRESS to Kconfig.soc since
it will most likely be the same values for all STM32 socs.
Change-Id: I682dc441e34155a19a4f90757707008ef299e9d4
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Add _arch_irq_is_enabled external interrupt API to find out
if an IRQ is enabled.
Change-id: I8ccbaa6d4640c1ab8369d2d35c01a2cfbb02f6cd
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Do not clear pending IRQ when enabling an IRQ on ARM
architectures. Peripherals and S/W ISRs may be required to
be deferred until they are enabled later and the pended
IRQ should be retained for the ISR to be vectored to when
enabled.
Change-id: I808183018d8a2cc58390a1de3b4797b2bb7c6ec9
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The '_timeout' structure is needed by dummy threads so that they can
handle timeouts.
Change-Id: Iefabd6ad93c8e176e95ce4262f5f3544dc90b7d5
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Quoting the product specification this device contains an "ARM
Cortex-M4 processor with floating-point unit" or, as this would
more normally be expressed an ARM Cortex-M4F.
Update Kconfig accordingly.
Change-Id: I5bd6f17724d0d4aa9aaab9961f12d4e8502c38a5
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Provide a random driver wrapped around the KSDK RNGA driver.
Origin: Original
Change-Id: I43feeb37d8d5173c7b95af8e80434fb7dc77a83e
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The ARM architecture port is fitted with support for the unified kernel,
namely:
- the interrupt/exception exit code now pends PendSV if the current
thread is not a coop thread and if the scheduler is not locked
- fiber_abort is replaced by k_thread_abort(), which takes a thread ID
as a parameter (i.e. does not only operate on the current thread)
- the _nanokernel.flags cache of _current.flags is not used anymore
(could be a source of bugs) and is not needed in the scheduling algo
- there is no 'task' field in the _nanokernel anymore: PendSV not calls
_get_next_ready_thread instead
- the _nanokernel.fiber field is replaced by a more sophisticated
ready_q, based on the microkernel's priority-bitmap-based one
- thread initialization initializes new fields in the tcs, and does not
initialize obsolete ones
- nano_private includes nano_internal.h from the unified directory
- The FIBER, TASK and PREEMPTIBLE flags do not exist anymore: the thread
priority drives the behaviour
- the tcs uses a dlist for queuing in both ready and wait queues instead
of a custom singly-linked list
- other new fields in the tcs include a schedule-lock count, a
back-pointer to init data (when the task is static) and a pointer to
swap data, needed when a thread pending on _Swap() must be passed more
then just one value (e.g. k_stack_pop() needs an error code and data)
- the 'fiber' and 'task' fields of _nanokernel are replaced with an O(1)
ready queue (taken from the microkernel)
- fiberRtnValueSet() is aliased to _set_thread_return_value since it
also operates on preempt threads now
- _set_thread_return_value_with_data() sets the swap_data field in
addition to a return value from _Swap()
- convenience aliases are created for shorter names:
- _current is defined as _nanokernel.current
- _ready_q is defined as _nanokernel.ready_q
- _Swap() sets the threads's return code to -EAGAIN before swapping out
to prevent timeouts to have to set it (solves hard issues in some
kernel objects).
Change-Id: I36c03c362bc2908dae064ec67e6b8469fc573983
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
They use data that is unavailable to the unified kernel, and are not
used anymore really. For now, only compile them when CONFIG_GDB_INFO=y,
and never enable CONFIG_GDB_INFO when building the unified kernel.
These files should go away when the unified kernel is made the only
kernel type.
Change-Id: I0a2a917dd453ecaae729125008756e0f676df16d
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Watchdog timer is enabled after the board reset. It is not used by Zephyr OS,
and having it enabled causes system resets during CPU-intensive operations.
Change-Id: If5583dbd2d2fb2206274467c523d6b5d147f1fbe
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Define symbolic constants for watchdog timer registers.
Provides the necessary interface to configure or disable
the watchdog timer.
Change-Id: I80002a843361569fdd78b725fc3f68e65195d02e
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
There is a total of 39 IRQs defined at nrf52/soc_irq.h.
Change-Id: Id478fb15a07cfdecaa6cc136730d20017b8752c5
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Zephyr uses the last priority level for the PendSV exception, but
sharing prio can still be useful on systems with a reduced set of
priorities, like Cortex-M0/M0+.
Change-Id: I767527419dcd8f67c2b406756b9208afd3b96de0
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Add a shim layer around the ksdk I2C driver to adapt it to the Zephyr
I2C interface. Currently only supports master mode.
Jira: ZEP-717
Change-Id: I704b8c38e22e456bb9fa4325682b2a354a27a7ba
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Since nrf.h abstracts the differences between the nRF51 and nRF52
architectures and chooses the right headers to include, it is
safer to use that instead of directly including the soc-specific
headers.
Jira: ZEP-702
Change-Id: I0e1758ede48f3422a41d226b0eab008e4ba2c77c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The ksdk provides a clock driver, fsl_clock.c, for the K64F and an
example usage of that driver, clock_config.c, for the Freedom board.
See ext/hal/ksdk/devices/MK64F12/
Leverage parts of clock_config.c to configure the clocks (specifically,
the sequence in BOARD_BootClockRUN()), but use the new Kconfig options
to set up the configuration structure. This will allow support for new
boards that may have a different external oscillator frequency or type.
Jira: ZEP-715
Change-Id: I3f0c75e6236f57600cd8b7f06f4482b13026fc10
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Many Kinetis SoCs contain an Oscillator (OSC) module and a Multipurpose
Clock Generator (MCG) module to configure clocks. Adding options to
configure these modules for PLL operation with different external
oscillator frequencies, which can vary across boards. More options may
be added later to support other clocking modes such as FLL.
Jira: ZEP-715
Change-Id: Ia121cc5b464d7e681883507bd756d331a8abd6ef
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The toolchain headers included an abstraction for defining symbol
names in assembly context in the situation where we're using a
DOS-style assembler that automatically prepends an underscore to
symbol names.
We aren't. Zephyr is an ELF platform. None of our toolchains do
this. Nothing sets the "TOOL_PREPENDS_UNDERSCORE" macro from within
the project, and it surely isn't an industry standard. Yank it out.
Now we can write assembler labels in natural syntax, and a few other
things fall out to simplify too.
(NOTE: these headers contain assembly code and will fail checkpatch.
That is an expected false positive.)
Change-Id: Ic89e74422b52fe50b3b7306a0347d7a560259581
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Completing the terminology change started with change 4008
by updating the Kconfig files processed to produce the
online documentation, plus header files processed by
doxygen. References to 'platform' are change to 'board'
Change-Id: Id0ed3dc1439a0ea0a4bd19d4904889cf79bec33e
Jira: ZEP-534
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add a Kconfig option to select between the Hard and Soft Float ABIs. We
also default to the Hard Float ABI as this is what older SDK versions
supported.
JIRA: ZEP-555
Change-Id: I2180c98cd7556ab49f5ca9b46b31add2c11bd07b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The K64F SoC initialization previously used macros and structs
custom-defined in Zephyr in order to access peripheral registers.
Refactored it to use CMSIS-style register accesses from the ksdk
instead.
Change-Id: I80975c62de07ec95cf830e99cd5b0abb9623acd0
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Utilize the gcc -print-libgcc-file-name to determine the path to
libgcc.a. Using this also resolve issues if we are building with
floating point and the various ABIs to pickup the right lib.
We can also simply a few Makefiles and remove the need to export
_CROSS_COMPILE_arm_isa.
Change-Id: I293394c921c18fa4984173ba51825d6f9a333697
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Arches now select whether they want to use the GCC built-ins,
their own assembly implementation, or the generic C code.
At the moment, the SDK compilers only support builtins for ARM
and X86. ZEP-557 opened to investigate further.
Change-Id: I53e411b4967d87f737338379bd482bd653f19422
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The comments for INT_ACTIVE and EXC_ACTIVE now refer to
"executing context ..." for all architectures.
Change-Id: Ib868958639a3b30e1814fcaa4d1f0651d3b2561e
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Used by ARC, ARM, Nios II. x86 has alternate code done in assembly.
Linker scripts had some alarming comments about data/BSS overlap,
but the beginning of BSS is aligned so this can't happen even if
the end of data isn't.
The common code doesn't use fake pointer values for the number of
words in these sections, don't compute or export them.
Change-Id: I4291c2a6d0222d0a3e95c140deae7539ebab3cc3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds Kconfig options CPU_HAS_FPU, FLOAT and FP_SHARING for the arm
architecture.
NOTE: All SOCs in the MK64F12 family have an FPU so that makes it a
convenient location to enable the hidden CPU_HAS_FPU option.
Change-Id: I71771d24f20f52079314bb8db9bf8a0aa827ab41
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Apply the correct compiler options when building for a Cortex-M4
processor that has floating point enabled. Using 'softfp' allows
floating point to be used with existing libraries supplied by the
Zephyr SDK. The 'hard' option would require new libraries to be
shipped with the SDK.
Change-Id: I141c20f54c2241134510888688637930c7b560a2
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Enable floating point in the Cortex-M4 processor.
Change-Id: Ibadae12b9197d6486fd5c6a3d4e177fa9e1c71bc
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Saves and loads the non-volatile FP registers (s16-s31) when switching
between threads.
Change-Id: Ib3190452d9a70d722032ac83176eb4fbb92aca3d
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds the preemptive floating point registers to the ARM's thread
control structure.
Change-Id: I65fbee6303091ce0658bbc442c4707d306b68e92
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Updates the exception stack frame structure to include floating point
registers.
Change-Id: I0fef784cf4d91dda245180abd75bfd9221825fba
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
at91sam3 supposed to go to Sleep mode and stop the CPU clock
(HCLK). It leads to JTAG problems. In order to be able to use
JTAG, we need to keep CPU clock on. This is achieved by
switching to Wait mode and keeping external main clock.
Since Wait mode switches off automatically Fast RC Oscillator,
but keeps external clock untouched.
Change-Id: Ife37a7691c3cbdf434e560725a71d419adafe054
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Add hidden configuration HAS_KSDK for SoCs to select if they have
support in the ksdk.
Change-Id: Ia4cd11901bc26d21a3bdfad6236d66656bb292cb
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
There was a reference to SOC_FAMILY_NRF5 which was not use by anyone
else and it seemes like it was a typo, where the right reference was
to symbol SOC_NRF5. However, the right fix is to move both sites to
use SOC_FAMILY_NRF5 *and* fix the SOC_SERIES to be only nrf52,
otherwise it causes path duplication and the build fails.
This was also causing documentation warnings that are thus killed.
Change-Id: I92e74a6158f02df43e6e857df8f1e67bcfdd9551
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
The ReST parser dislikes enumerations with no empty lines in
between. Whatever.
Change-Id: I480c08fe5b69f0d0f3ebfacdc64fc9e3ec94da21
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
The KSDK device header files require a preprocessor macro that defines
the part number string (e.g., MK64FN1M0VMD12). Create a hidden Kconfig
option to hold the part number string, and hidden Kconfig options that
the board Kconfig will use to select the specific part number.
Change-Id: I612e785026261e425b47b5b7fae0c65b4f94b30b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Include nrf.h instead of directly using the specific header
required. This will be useful in the future when additional
Nordic ICs are supported.
JIRA: ZEP-377
Change-Id: I7a7257b0aaa5fa0a0d202322c366efbdd1d84458
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Translate CONFIG_SOC_SERIES_NRF52X to NRF52, which is the macro
expected by the Nordic MDK headers.
JIRA: ZEP-377
Change-Id: Ic846e4cddf8146ae9d96bc98d4b12311552dc4f6
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Generate kernel image in Intel Hex format when building for the nRF52.
Remove the additional step from the board doc file.
Change-Id: I619496f64037c2a0ac459ae05e549e01458e0f71
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Moved setting of specific Cortex-M compiler flags in each SoC directory
unify setting them in the arch/arm/soc Makefile.
Add flags for Cortex M0, M0+, M1, M3, M4, and M7. However only
CONFIG_CPU_CORTEX_M3 and CONFIG_CPU_CORTEX_M4 are supported at this time
As part of this change converted Kbuild files for some SoCs into
Makefiles as the Makefiles would be empty otherwise.
Change-Id: Ie4e0178b141ca761ec482a610ae50e94fe58070f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a soc-cflags, soc-cxxflags, and soc-aflags as a means for
SoC specific compiler flags to be set without manipulating Kbuild
options directly.
Change-Id: I2c8f5019fb237429e59717ef96bd4251a61dc1a5
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the same Kconfig infrastructure and options for all SPI drivers.
Jira: ZEP-294
Change-Id: I7097bf3d2e1040fcec166761a9342bff707de4dd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Avoids confusion with .gitignore rules, which were inadequate to
cover all the places where these files are found. At least in
VIM, these files are now syntax highlighted correctly.
Change-Id: I23810b0ed34129320cc2760e19ed1a610afe039e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fibers initialize this back pointer to NULL as they are (by definition)
not microkernel tasks. Microkernel tasks initialize it to their
corresponding 'ktask_t'.
However for nanokernel systems, the back pointer is always NULL. This
is because there is only one task in a nanokernel system (the background
task) and it can not pend on a nanokernel object--it must poll.
Change-Id: I9840fecc44224bef63d09d587d703720cf33ad57
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds a back pointer to the microkernel task to the TCS when
configured for a microkernel. This is a necessary prerequisite
to support microkernel tasks pending on nanokernel objects.
Change-Id: Ia62f9cf482ca20b008772dad80cbfd6acb6f5b7a
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
We really should have more faith in the compiler, it generates
code to implement this exactly like the arch-specific assembly
versions, and on ARM is actually 4 bytes shorter.
FUNC_NO_FP used to disable the usual C preamble to update the
frame/stack pointers, which is how the sizes are still the same
or less. It's debatable how useful the occasional use of
FUNC_NO_FP is in practice since it hinders debugging and in a
production build frame pointers should be globally disabled, but
we can address that later.
Change-Id: I6c4b64ab3e3a9b6f91d52fa8c92e6e79a986fc77
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Of the 3 related functions;
_thread_essential_set()
_thread_essential_clear()
_is_thread_essential()
The first two are parameter-less and always operate on
"_nanokernel.current". The last one takes a 'thread' parameter but will
operate on _nanokernel.current if the parameter is NULL. All calls to
_is_thread_essential() pass NULL!
This change makes the 3 functions consistent by removing the parameter
to the 3rd function. This should also be marginally more efficient,
though consistency was the motivation. This change corrects the doc
preamble to all 3 functions.
(These functions would probably be better as inlines. Also, the choice
of when to use wrappers seems a bit arbitrary. E.g. there's nothing
for setting/testing the "FIBER" flag.)
Change-Id: Ie3589f8a28b227c6d7a3a31b664d3b3e6e9c6d17
Signed-off-by: Geoff Thorpe <geoff.thorpe@nxp.com>
The UART console init should be done after UART init. So it can be
folded into general UART init, thus one fewer SYS_INIT().
Change-Id: Ifb18c5308dfef790325e6bff5bc7b5976fcd421e
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The clkInit() is always called so this can be inlined.
This saves 32 bytes of ROM space compared to non-inlined version.
Change-Id: I2cb6d02c0996acad16029be243f6059183938089
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The clock_init() is always called so this can be inlined.
This saves 32 bytes of ROM space compared to non-inlined version.
Change-Id: I1b95142da4c22f4b7fc7f7f6210503d90cf65cc9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This also enables GPIO on ATMEL SAM3 when GPIO is set.
Change-Id: I4125af4910d57bed98b0ee4967fb696e3f345e67
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The files soc_config.c and soc_gpio.c use errno code so they should
include errno.h.
Change-Id: I94237aa294701cc71ed17ea42eca9d8073d4ae47
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
It was not possible to add directories under an SoC family
because of the direct call to Makefile in the SoC series from the
architecture level.
While we have SoC still using the old structure, add a conditional
to still support old structure and allow Makefiles directly under
an SoC family directory.
This is useful for adding drivers and BSP files common to one family.
Change-Id: I85dc8341523b41949de91d78675153ce0baa5aac
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
With most boards there's no simple way to get access to the HCI
traffic. Simultaneously these boards only have one external UART for
the console. This patch introduces a protocol which combines both
normal logs and HCI logs over a single binary protocol sent over the
console UART.
The protocol is modeled based on the btsnoop/monitor protocols used by
BlueZ, and the first tool that's able to decode this is btmon from
BlueZ ("btmon --tty <tty>").
For platforms with two or more external UARTs it is still possible to
use CONFIG_UART_CONSOLE as long as the UART devices used are
different, however on platforms with a single external UART
UART_CONSOLE should be disabled if BLUETOOTH_DEBUG_MONITOR is enabled
(in this case printk/printf get encoded to the monitor protocol).
Origin: Original
Change-Id: I9d3997c7a06fe48e7decb212b2ac9bd8b8f9b74c
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use SOC_FAMILY and SOC_SERIES to identify soc families and series
and to point to the correct linker files and files related to a
specific SoC.
Change-Id: I8b1a7339f37d6ea4161d03073d36557a40c0b4a6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use SoC family/series and reoganise the structure to follow new
hierarchy.
Change-Id: I8637f1487a8287a6614ce6636cd018cf342fec95
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add Kinetis SoC family and rename fsl_frdm_k64f to mk64f12.
This will allow adding new SoCs of the same family and the reuse of code
among SoCs of the family and series.
Change-Id: Iea1a663aef7ce0487f147bdd36f668bebe80deb5
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use SOC_SERIES_* for naming SoCs with similar features and architectures
with the goal of code reuse. The Series in the config variable should avoid
name collisions and clearly denote the relationships within an SoC family.
Change-Id: I7a98542f96b5d5dc3acc23782c4d45f98cceb599
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use CONFIG_SOC_FAMILY for the top level SoC family. A family
will have different SoCs or different SoC series with multiple
SoCs.
Adding the Family string to the config variable to avoid confusion
between actual SoCs and families and to prevent name collisions.
Change-Id: Ic99a2c1df7850dee3a45641027af82464dd6fadb
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ifd65097a65f80539cac073f95aadc2d8e42efb9f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
GCC enables unaligned memory access for ARMv6 and above.
Once unaligned memory access is allowed, there's no need
for the unaligned memory access trap.
The change prevents the situation when the compiler
generates code that uses unaligned memory access, but
the CPU generates an exception when this code runs.
Change-Id: Id33f2264c631772e5c561e76fb579d8b7bc26e1e
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
There is no need to re-define CONFIG_UART_CONSOLE_ON_DEV_NAME to be
"UART_0" all over the place as its default is "UART_0" already.
So remove those duplicate defaults.
Change-Id: Ia86e26b8f90540fdbd7dcb3358d6dac352648b21
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The pinmux base address and number of pins are now defined in SoC or board
header files instead of specifying them in kconfig. This is because
the pinmux ties directly to the SoC (or board expanders) so the base
address and number of pins do not need to be configurable in kconfig.
Change-Id: Ib6090d7d022b491f3fe8f522858281504c6302bb
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The base address, IRQ line, chip select numbers, and clock
gating constants are static per SoC, so there is no need to
make them configurable in Kconfig.
Change-Id: I9f87ca29c28c38c42d4e4f1a3a41fa231f63ef03
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The base address and IRQ line are static per SoC, so there is no need
to make them configurable in Kconfig.
Change-Id: Ib78401ff136c29642356f5bda9d6cd3e5c98bece
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The UART port base address, IRQ line and clock frequency are static
per SoC, so there is no need to make them configurable in Kconfig.
Change-Id: Ia252958d205e0100d1b92e2a12d4c22411bc94b9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The UART port base address, IRQ line and clock frequency are static
per SoC, so there is no need to make them configurable in Kconfig.
Change-Id: I79b142414143bc5ef585d3136a00375233de1723
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds conditions to the default values for device init priorities,
and make them follow the dependencies on the config options. This cleans
up the resulting .config a bit, making it easier to read.
Change-Id: Ib05806ac6108d465ffe245142ecca7a51be6df22
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Changed names of Kconfig flags, variables, functions, files and
return codes consistent with names used in the RFC. Updated
relevant comments to match the changes.
Origin: Original
Change-Id: Ie7941032d7ad7af61fc02928f74538745e7966e8
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This moves the STM32 based boards (Nucleo F103RB and STM32 Mini A15) to
the "new" pinmux model.
Change-Id: I190df271a6b83fafeec0b281cd4ee7cf13d7e7db
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Setting the direction of a GPIO pin is not the responsibility of the
pinmux "board" initialisation. This should be left for the GPIO
utilising application.
Some macros that were only used when setting the pin direction are
removed.
Change-Id: I5b63d52446a27fe539c89f0639a8dcadf5ea9f80
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This patch replaces all occurrences of DEV_* codes by errno.h codes at
the arch layer.
Change-Id: I1a1ab6d0481f3660ad032e2690d2577245fe1f34
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
CONFIG_PWM is set to "no" by default, so there is no need
to do it in the SoC kconfig file. Also, setting CONFIG_PWM
there causes kconfig to think that CONFIG_PWM depends on
CONFIG_SOC_FSL_FRDM_K64F and gives warnings about
unmet dependencies if the certain combinations of CONFIG
are set.
Change-Id: I0028accfc4b585dcfa87e0d5733b789691a598e3
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This makes this board more consistent with the rest of the code base.
Change-Id: I5641c6358e638a3585d2154e67d3536b11436e01
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Use of `ldr` triggers unaligned memory access when loading SVC
instruction to r0. This is caused by the fact that SVC is a 16-bit
instruction, hence with a 2 byte offset, we are performing an non-word
aligned access. Prevent this by using `ldrh` to load a halfwords rather
than full words.
Change-Id: Ieae60c2ce86c6cfe15c89627d3a450797ce7e714
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add support for use of HSE (incorrectly named PREDIV1)as input of PLL,
along with HSE bypass for stabilized external clock, and XTPRE
prescaler. Update PLL handling so that we do not unnecessarily enable
PLL clocks, instead enabling only the clocks sources that are required
as per user's configuration.
This change allows higher SYSCLK clock values, up to 72MHz.
Change-Id: Ia7c2be3ce11ac0de2efa664b20e7ab5fddd57a51
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add mapping of registers for embedded flash controller.
Change-Id: I81f891551124e9f124ff59dfe0b3c737ec5b3b63
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Before moving pinmux related code to 'drivers/pinmux' fix their return
codes to be consistent with the rest of the API.
Change-Id: Ie84f64e93745d44bef8b9d2119f6a05cdc8cb8c4
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Add a driver for Independent Watchdog (IWDG) commonly found in STM32
MCUs. The driver has been tested on STM32F1 family MCU.
Change-Id: Idc6ac35990e46901a206b4af0ce3767eb4875de9
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add necessary integration for supporting interrupts on GPIO input pins
for STM32F1 line of MCUs.
Change-Id: I0526a85cc3fdb96891c93ba4840ef27d613ab31b
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add mapping of Alternate Function I/O (AFIO) registers for STM32F1 MCU.
Change-Id: Id3e12290d6869c1f0506549f21407b3cd80d0a64
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Introcuce a driver for External Interrupt/Event Controller (EXTI) found
on STM32 MCUs.
Change-Id: Ib206521fcc51b5dfaaf5dea9d436f8304f3a36be
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add a list of symbolic constants for IRQ lines available on
STM32F1 line of MCUs.
Change-Id: Iebf1847719c0db31cf852529fe5876e3cabbfe52
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add necessary integration code enabling use of common STM32 pinmux
driver.
The alternate function listing currently consists of USART1 pins
only. The listing should be updated when support for more devices is
added.
Change-Id: Ic65aeea9df9aaea7636ecdd6996f56e6ef59dc2f
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add functions required for integration with common STM32 GPIO driver.
Change-Id: Ic6637e991f5c0cf659f3b927ed47ef482b13b64f
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Make kconfig look the same for all architectures.
JIRA: ZEP-107
Change-Id: Ia8100194ec333fc07a1dff4f6f90364ce8bef4d3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The patch adds a driver for STM32F10x series RCC (Reset and Clock
Control) subsystem.
The module is primarily responsible for setting up of MCU's clock
tree. In particular the driver sets up SYSCLK, PLL (with source
configuration), AHB prescaler, and APB1/APB2 prescalers. As part of this
functionality, the subsystem can enable/disable clock signal for
particular peripherals, thus reducing the power consumption of the MCU.
The driver implements clock control driver API. However, subsystem IDs
being HW specific are exposed in driver public header that must be
included by callers. The driver registers a single device using a common
name STM32_CLOCK_CONTROL_NAME. The device is initialized at
the PRIMARY level with priority 1. This allows the initialization to
take place right after SoC initialization routine.
The driver depends on selection of SOC_STM32F1X config option and is MCU
specific.
Change-Id: I8bea5db20726a24bce7b7ffe0b95de543240429a
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
The patch introduces a new family of SoCs based on STMicroelectronics'
STM32 MCU line. The patch introduces a basic arch/arm/soc layout along
with configuration of 2 MCUs from STM32F1 series: STM32F103VE and
STM32F103RB.
The patch assumes that other MCUs from STM32 family will be included
under arch/arm/soc/st_stm32 tree, to achieve the following layout:
arch/
arm/
soc/
st_stm32/
stm32f0/
stm32f1/
stm32f2/
...
stm32l0/
Most of the configuration within a single MCU family (ex. STM32F1) is
shared, however individual MCUs differ with respect to SRAM size, flash
size or the number of available peripherals. The patch assumes that per
MCU line Kconfig.soc.family file should introduce basic setup for given
series. This can be further tuned by per MCU files, with
Kconfig.soc.stm32f103rb and Kconfig.soc.stm32f103ve as examples.
Each family defines a configuration option, ex. CONFIG_STM32F10X, while
individual MCUs define a corresponding per MCU config options,
ex. CONFIG_STM32F103VE.
From the menuconfig perspective, the user is presented with a family
selection under General Platform Configuration/SoC Selection. A
specific MCU model can be selected by accessing General Platform
Configuration/STM32F1x MCU Selection, with the default entry being
selected by the board configuration.
Change-Id: I22e4defd4a08ed1b2e2cad0e214b34f565e08831
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
This makes sure the CONFIG_GPIO_K64F_* kconfig options have correct
dependencies. Or else CONFIG_GPIO_K64F can be disabled, but all
the CONFIG_GPIO_K64F_{A,B,C,D,E} are enabled.
Same goes for SPI, FTM and pinmux.
Change-Id: I8d225dea714081b14b19006d61b8f3f6afafa5ee
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC selections for each architecture are moved to the top level
in menuconfig and xconfig. This makes it more intuitive to select
architecture -> SoC -> then board, avoiding an additional trip to
go into the architecture menu to select SoC.
Change-Id: I57a78a09adfc4bb12423915b6ad14ceb74381a2b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The nmi_on_reset.S functions are used by all ARM platforms. It
makes no sense to repeat the same code for all platforms. Moving
the code from each SOC implementation to arch/arm/core.
The same treatment for the NMI_INIT() macro. Moving it from a per
SOC implementation to the include/arch/arm/cortex_m/nmi.h.
Change-Id: I574d8880a44046cc7b9e1b635e80d6e83657b8c1
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
The thread monitor allows to iterate over the thread context
structures for each existing thread (fiber/task) in the system.
Thread context structures do not expose thread entry information
directly. Although all the information can be scavenged from memory
stacks. Besides, accessing the information depends on the stack
implementation for each architecture.
By extending the tcs we allow a direct access to the thread
entry point and its parameters, only when thread monitor is
enabled.
It also allows a task to access its kernel task structure
through the first parameter of the thread.
This allows a debugger application to access the information directly
from the thread context structures list.
Change-Id: I0a435942b80eddffdf405016ac4056eb7aa1239c
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
This reverts commit 3f6884902b.
This commit does not work as intended: the part in arch/arm/Makefile
gets ignored and -mcpu=cortex-m3/4 does not get passed to gcc. It seems
that the zephyr toolchain does not care, but the vxworks assembler
chokes if it is missing, and thinks the CPU does not support thumb ISA
Change-Id: I14d11d3e22dac4952bdab3eb9e2d1c36b1a686c2
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Support for Freescale/NXP K64 SPI modules, limited to:
- Master mode
- A single active set of clock and transfer attributes (CTAR0), which
includes non-adjustable delay parameters
- Tx FIFO fill and Rx FIFO drain interrupt handling
- Standard, continuous select and continuous SCK SPI transfer formats
Also, divide-by-zero code generation in this driver is prevented.
The 'volatile' attribute is added to some of the variables in the baud
rate and delay calculation functions of the K64 SPI driver in order to
prevent bad code generation by gcc toolchains for ARM seen when an
optimization setting above -O0 is used.
Specifically, a register is loaded with the constant 0 and is used as
the divisor in a following divide instruction, resulting in a
divide-by-zero exception.
This issue has been seen with gcc versions 4.8.1 (the VxWorks toolchain)
and 5.2.0 (the Zephyr SDK toolchain).
Change-Id: Ib5b2b748aad8fdfd5e8d40544e6e1abef3713abe
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Internal K64 SoC clock dividers were hard-coded. They've been replaced
with config options.
Change-Id: I583307f2e3341525f4445e9ceb89d36634b12802
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
PWM support using the Freescale K64 FlexTimer Module (FTM)
Change-Id: Iaad429c01bd877babba04e84d6a4679bd7e38120
Work-by: Mike Hirst <michael.hirst@windriver.com>
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
K64 pinmux support is created as a normal driver.
As opposed to the Galileo board, the pin configuration options are
defined by the MCU and are not board-specific. Separate
platform/board-specific configuration code uses the pinmux driver for
the default pin settings. For FRDM-K64F, only the Arduino pins (22 of a
possible 160) are set up.
Some of the I/O pins routed to the Arduino header are also configured as
JTAG/SWD signals by default and are used by the OpenSDAv2 debug
interface. Therefore, a PRESERVE_JTAG_IO_PINS config option was created
for the FRDM-K64 platform to prevent the default pin settings from
re-configuring these pins.
The K64 MCU separates pin configuration and control, implemented in the
pinmux driver, from GPIO. This results in some cross referencing
between the K64 GPIO driver and the K64 pinmux driver due to the
dependencies of one on the other.
This pinmux driver also uses the expanded pinmux function/mode parameter
size to describe pin configuration options with bit fields for the K64,
including up to 8 pin functions, plus interrupt, pullup/down, drive
strength, open-drain and slew rate.
The following GCC warnings in the K64 pinmux driver are prevented when not
compiling with 'no-optimization' (-O0):
warning: 'gpio_dev' may be used uninitialized in this function
[-Wmaybe-uninitialized]
Change-Id: Ie5031d18750143bf895883058b3cd55fd9989fd3
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
Basic driver support for the Freescale K64 GPIO module.
Note that only pin direction, read and write are supported.
Change-Id: I6587bb260197a00497be9ac991002e3dde54718d
Signed-off-by: Jeff Blais <jeff.blais@windriver.com>
This table was still being added to ROM even if
CONFIG_SW_ISR_TABLE=n.
Change-Id: Ia0de1349960af1c62e88344b3d5b6655b638219b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This config option is no longer implemented and doesn't actually
do anything.
Change-Id: I57ab7ba688f57da21f8a58f62ea37dc6b8daaf18
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We don't support hard-coding vectors in this table anymore.
If someone really wants to do this, they can set
IRQ_VECTOR_TABLE_CUSTOM and define their own.
Change-Id: I45f49782ba5fefb0a02eab02ec96efd0019bc6d5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The peripherals utilizing UART were required to register their own
ISR rountines. This means that all those peripherals drivers need
to know which IRQ line is attached to a UART controller, and all
the other config values required to register a ISR. This causes
scalibility issue as every board and peripherals have to define
those values.
Another reason for this patch is to support virtual serial ports.
Virtual serial ports do not have physical interrupt lines to
attach, and thus would not work.
This patch adds a simple callback mechanism, which calls a function
when UART interrupts are triggered. The low level plumbing still needs
to be done by the peripheral drivers, as these drivers may need to
access low level capability of UART to function correctly. This simply
moves the interrupt setup into the UART drivers themselves. By doing
this, the peripheral drivers do not need to know all the config values
to properly setup the interrupts and attaching the ISR. One drawback
is that this adds to the interrupt latency.
Note that this patch breaks backward compatibility in terms of
setting up interrupt for UART controller. How to use UART is still
the same.
This also addresses the following issues:
() UART driver for Atmel SAM3 currently does not support interrupts.
So remove the code from vector table. This will be updated when
there is interrupt support for the driver.
() Corrected some config options for Stellaris UART driver.
This was tested with samples/shell on Arduino 101, and on QEMU
(Cortex-M3 and x86).
Origin: original code
Change-Id: Ib4593d8ccd711f4e97d388c7293205d213be1aec
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Currently the build system has hardcoded values for the -march/-mcpu
which identify what architecture should be used when compiling ARM code.
For processors such as the STM32 this will need to be defined by a per
SOC process.
Change-Id: Ia8158cd687d8d0432ea420e204bb2bc67d33a054
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
This patch updates some help sections to remove the "ERROR:
Unexpected indentation" messages during hmtl documentation
generation.
Change-Id: Idcdc17727b921b6145f9eb28d85975ceca273ce2
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The app-facing interface for configuring interrupts was never
formally defined, instead it was defined separately for each arch
in their respective arch-specific header files. Occasionally these
would go out of sync.
Now there is a single irq.h header which defines this interface.
To avoid runtime overhead, these map to _arch_* implementations of
each that must be defined in headers pulled in by arch/cpu.h.
Change-Id: I69afbeff31fd07f981b5b291f3c427296b00a4ef
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We have a new policy: users should not be able to configure
an interrupt with "forbidden" priority levels, and any priority
levels with special semantics will be activated by flags.
Change-Id: I757c19cfedcb1d0938eaf4da348ddafb71b3e001
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds the driver to utilize the I2C/TWI interface on Atmel SAM3
family processors for I2C communication.
Note that this currently only supports master mode. Limited
testing has been done using the Fujitsu FRAM sample app.
Change-Id: Ibdb8277e47dd9450b49a66a95421eb1ffb1c4eb4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Adds the struct to describe PDC (Peripheral DMA Controller).
The PDC is being used by peripherals to initiate DMA
transfers.
Change-Id: Ida2a20810c4f2ef972e9669c45e22da07c1576ab
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Decisions on compiler optimizations were done on the architecture level,
this does not scale and some SoCs will have different optimization levels
or compiler options needed. Moving this to the SoC makes it easy to optimize
differently when using the same CPU which we use to set the right optimization
now on the architecture level.
For IAMCU platforms, use the right architecture and tuning.
-march=lakemont -mtune=lakemont -miamcu -msoft-float
Change-Id: I458afca5feb9be5de8dcae559d6dcac3c6d6a2a7
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The default Kconfig option is missing a condition for the SRAM
base address on SAM3X8E. Add it back so the correct default
can be used.
Change-Id: Ib4103366f693648c76630cbbd71ca98109381d5c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The PIO controllers on Atmel SAM3 family processors can be
used for GPIOs, so this is the driver.
Change-Id: I3d5712f3a0a71025b820ca1c08dd767ee1e136d8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Mostly SoC initialization and some kernel subsystems, but also some
device drivers like the interrupt controllers.
Change-Id: I8dc1844c33acd877c075b6b03558fdca6f87500b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Static interrupts rely on a trick where the _sw_isr_table array
is declared with each element in a different .gnu.linkonce
section, initially pointing to the spurious IRQ handler.
When drivers or apps declare their own interrupts, they override
the element with their own containing the real ISR and parameter.
However, this only works if the initial declaration of the
_sw_isr_table array with the spurious handlers is linked last.
App-specific code was being linked later than the core code,
causing static interrupts declared in apps not to be installed
correctly.
If the _sw_isr_table is moved from SOC-specific code to core arch
code, interrupts configured under soc/ should still also work.
Change-Id: Iec7df47386dfbbf2956a807da27dc8aa6e01b268
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This simulates a reboot by jumping back to the address stored in the
reset vector in vector table found at address 0. It is supported from
interrupt/exception level, which means that sys_arch_reboot() in this
case finds out if it is called from thread mode or handler mode, and in
the latter case, it unwinds the nested exception stack as needed.
Change-Id: Ib67f850f8411f1ee8fc592a5f31f2f70d0af14a4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The bootloader expects the entry point to be called __start, not __reset.
Change-Id: I5a5f7f45c248b9398e58fb026c731f8617fe4856
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Add sys_exc_connect() (and its x86-compatible alias nanoCpuExcConnect())
that allows connecting an exception handler at runtime.
The current implementation is a bit of a bastard, to avoid disturbing
the current implementation of the exception handlers. Instead of hooking
_exc_wrapper() in all vectors and adapting the exception handlers, the
current exception handlers are still hooked directly in the vectors.
When an exception is hooked at runtime, _exc_wrapper() gets installed in
the vector and the real handler gets inserted in _sw_exc_table; this
means that the scheme only works with non-XIP kernels.
This should be enhanced so that _exc_wrapper() is hooked in all vectors,
and that current exception handlers (for faults mostly) are reworked to
be inserted in the _sw_exc_table and wrapped in _exc_wrapper().
Change-Id: Icaa14f4835b57873d2905b7fbcbb94eeb3b247d1
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
For non-XIP systems, it's not in ROM, so remove the "ROM" part. Adapt it
to coding conventions at the same time, and export it to C code.
Change-Id: Id09a6be8bc9c462667ed71b53be7fa5382c88db3
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Find out on which stack the stack frame for an exception is in the assembly
code (__fault()) rather than in C (_Fault()). This will allow pushing
more registers on the stack when debugging is enabled.
Change-Id: I1c510b83098536f8930392b17df27511ccd04d80
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename the function and allow it to handle the 'type'
argument, which is ignored in this case.
Change-Id: I3d3493bea4511b2d026747505e7e52c5acc85012
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The ESF was built using the 'alias' names of the GPRs (a1, lr, pc, etc)
rather than their 'real' name (rN).
Change-Id: I49cae5e94869a79a3165dc7f2347d8cec39dbf67
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The processor is made aware that the vector table built in the image is
located at the start of SRAM in the case of a non-XIP image, rather than
at 0 in as is the case in XIP images.
Change-Id: I40b28ca32daf3e8930f103224766ed4e0ccc88e0
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The image will be linked at a different address and with different
ROM/RAM sizes to allow running a bootloder image that loads a payload
image. The addresses/sizes depend on if it is a XIP image or not
(CONFIG_XIP), and in the case of a XIP image, if it is a bootloader
image (CONFIG_IS_BOOTLOADER) or not.
In the case of a bootloader, it is given the full ROM and
CONFIG_BOOTLOADER_SRAM_SIZE kB of SRAM. When not a XIP image, it is given
the full SRAM minus CONFIG_BOOTLOADER_SRAM_SIZE kB, and is linked at the
start of SRAM.
Change-Id: Ibbb693c7bff022f313dac40f21c04a61f4bed115
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
This board needs 16 bytes to be written with a specific value when the
target boots. This is only necessary when running a XIP image which
exists around those 16 bytes.
Change-Id: Ifd26b3842f09137765d9c7d1678476bfda8a563f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Fix an issue where, if a task is pending on a nano timeout, the duration
it wants to wait is not taken into account by the tickless idle code.
This could cause a system to wait forever, or to the limit of the timer
hardware (which is forever, for all intents and purposes).
This fix is to add one field in the nanokernel data structure for one
task to record the amount of ticks it will wait on a nano timeout. Only
one task has to be able to record this information, since, these waits
being looping busy waits, the task of highest priority is the only task
that can be actively waiting with a nano timeout. If a task of lower
priority was previously waiting, and a new task is now waiting, it means
that the wait of the original task has been interrupted, which will
cause said task to run the busy loop on the object again when it gets
scheduled, and the number of ticks it wants to wait has to be recomputed
and recorded again.
Change-Id: Ibcf0f288fc42d96897642cfee00ab7359716703f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds C++ support to the build system.
Change-Id: Ice1e57a13598e7a48b0bf3298fc318f4ce012ee6
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds extern "C" { } blocks to header files so that they can be
safely used by C++ source files.
Change-Id: Ia4db0c36a5dac5d3de351184a297d2af0df64532
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
We can save a great deal of RAM this way, it only needs to be
in RAM if dynamic interrupts are in use.
At some point this config option broke, probably when static
interrupts were introduced into the system.
To induce build (instead of runtime) errors when irq_connect_dynamic()
is used without putting the table in RAM, the dynamic interrupt
functions are now conditionally compiled.
Change-Id: I4860508746fd375d189390163876c59b6c544c9a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This adds driver for the UART controller on Atmel SAM3X8E.
This UART controller only has two wires for RX and TX, and
does not have flow control (e.g. CTS, RTS) or FIFO.
Currently, the driver does not support any interrupt driven
operations.
Change-Id: I63720bccfb70a89888353b8ee3dfc4b80793dc01
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds initial support for Atmel SAM3X8E processor, which is
based on ARM Cortex-M3. The SAM3X8E is being used on Arduino Due.
Change-Id: I199efcf29629f9ebacad474e5edc91bc3757f613
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This removes the default flash and SRAM base addresses from the ARM core
Kconfig file. Each individual SoC/processors Kconfig has to define them.
This is in preparation to support Atmel SAM3 family processors as they
have different base addresses.
Change-Id: I97ea9b43386d1e286ee692f583c97cfbb5399b0f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This reverts commit 778d5b11c5327be4b40c7745e9beaecfd6327e13.
This patch has been identified as breaking the build when trying
to manually build non-x86 applications.
Change-Id: I1857745049dfef7193de58737108314b7aae01c5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Decisions on compiler optimizations were done on the architecture level,
this does not scale and some SoCs will have different optimization levels
or compiler options needed. Moving this to the SoC makes it easy to optimize
differently when using the same CPU which we use to set the right optimization
now on the architecture level.
For IAMCU platforms, use the right architecture and tuning.
-march=lakemont -mtune=lakemont -miamcu -msoft-float
Change-Id: I0f77cffe7a139f8b2620935094437d0dfd160dfe
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The Kbuild system first looks for a Kbuild file, then it looks for
a make file.
Use the Kbuild for object building and leave the Makefile for definding
build options and compiler flags and other SoC related defines.
Change-Id: I0be59bb5ae02a29108a188efbd6f14dcdb7de4ee
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The interrupt API has been redesigned:
- irq_connect() for dynamic interrupts renamed to irq_connect_dynamic().
It will be used in situations where the new static irq_connect()
won't work, i.e. the value of arguments can't be computed at build time
- a new API for static interrupts replaces irq_connect(). it is used
exactly the same way as its dynamic counterpart. The old static irq
macros will be removed
- Separate stub assembly files are no longer needed as the stubs are now
generated inline with irq_connect()
ReST documentation updated for the changed API. Some detail about the
IDT in ROM added, and an oblique reference to the internal-only
_irq_handler_set() API removed; we don't talk about internal APIs in
the official documentation.
Change-Id: I280519993da0e0fe671eb537a876f67de33d3cd4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch moves the CONFIG_STACK_CANARIES check from architecture's
Makefile to the root Makefile since this option is kernel-related,
not architecture-related. This way we avoid replicating the same
CONFIG_STACK_CANARIES check in several Makefiles.
This patch also removes some blank lines from the Makefiles it touches.
Change-Id: I458f92fa6799526c608369d1e56579936bcb196e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Changes the nanokernel stack API so that the timeout parameter must be
specified when invoking nano_isr_stack_pop(), nano_fiber_stack_pop(),
nano_task_stack_pop() and nano_stack_pop().
This obsoletes the following APIs:
nano_fiber_stack_pop_wait()
nano_task_stack_pop_wait()
nano_stack_pop_wait()
Note that even though the new API requires that the timeout parameter
be specified, there are currently only two acceptable values:
TICKS_NONE and TICKS_UNLIMITED
This nanokernel option does not support CONFIG_NANO_TIMEOUTS.
Change-Id: Ic7f16ee30c3534115ceffa19ef8591ecc5a79080
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Changes the nanokernel LIFO API so that the timeout parameter must be
specified when invoking nano_isr_lifo_get(), nano_fiber_lifo_get(),
nano_task_lifo_get() and nano_lifo_get().
This obsoletes the following APIs:
nano_fiber_lifo_get_wait()
nano_fiber_lifo_get_wait_timeout()
nano_task_lifo_get_wait()
nano_task_lifo_get_wait_timeout()
nano_lifo_get_wait()
nano_lifo_get_wait_timeout()
Change-Id: Ie9f93e46da42ea33c32544c02ab1d70b893cc198
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Changes the nanokernel semaphore API so that the timeout parameter must be
specified when invoking nano_isr_sem_take(), nano_fiber_sem_take(),
nano_task_sem_take() and nano_sem_take().
This obsoletes the following APIs:
nano_fiber_sem_take_wait()
nano_fiber_sem_take_wait_timeout()
nano_task_sem_take_wait()
nano_task_sem_take_wait_timeout()
nano_sem_take_wait()
nano_sem_take_wait_timeout()
Change-Id: If7a4bce1bd8ec8d6410d04f3c16ff1922ff0910e
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Changes the nanokernel FIFO API so that the timeout parameter must be
specified when invoking nano_isr_fifo_get(), nano_fiber_fifo_get(),
nano_task_fifo_get() and nano_fifo_get().
This obsoletes the following APIs:
nano_fiber_fifo_get_wait()
nano_fiber_fifo_get_wait_timeout()
nano_task_fifo_get_wait()
nano_task_fifo_get_wait_timeout()
nano_fifo_get_wait()
nano_fifo_get_wait_timeout()
Change-Id: Icbd2909292f1ced0bad8a70a075478536a141ef2
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Causes problems for large values of CONFIG_NUM_IRQS.
Some inconsistencies have been noted in how CONFIG_NUM_IRQS is
used on these platforms, with bugs filed. This patch preserves
existing behavior and has been shown to generate the same number
of table entries for both arches using objdump.
Change-Id: I1d3ac5466978acb56e88a6dc3cbe7cc09431e94d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Change terminology and use SoC instead of platform. An SoC provides
features and default configurations available with an SoC. A board
implements the SoC and adds more features and IP block specific to the
board to extend the SoC functionality such as sensors and debugging
features.
Change-Id: I15e8d78a6d4ecd5cfb3bc25ced9ba77e5ea1122f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Previous it was renamed in favor of Qemu, now that we have board support
we move this to the original name and derive a qemu board out of the
platform.
Change-Id: Ia8769b27defa0a39503ecf2e6ec7fc6304b6ff49
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Define boards based on platforms/SoCs and define them under boards/.
Also unify the naming of all platform, SoC and board files and use
platform.h for platforms and board.h for boards.
Change-Id: Icfeb96479ab5800aca98c80a79bdc3cecd645314
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The code to poke the system integration module to disable clock gating
for UARTs only works for UART0-3 since all the bits are in the same
register. However, clocks for UART4 and UART5 are controlled by
another register. This means that we have been writing to the wrong
bit for enabling UART4.
This patch fixes this issue, and moves the clock gating clock into
board initialization. The incorrect code has also been removed to
prevent accidental mis-use. The dev_data struct is no longer needed
for uart_k20, so that is removed as well.
Change-Id: I67845a417e43647bf0ffcbdbda34ce68fa887713
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Hardware initialization for fsl_frdm_k64f has to be done at the very
beginning at boot, before anything else. So change the init priority
for hardware initialization to 0. This makes sure the hardware is
initialized. Or else any memory/register access will hang
the board.
Change-Id: Idc1c9449bb7cd1ec7b8d8f44004ea76cc7c09a18
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
To many people, IPI connotes inter-processor interrupts on SMP
systems. Rename this to IPM, or Inter-Processor Mailboxes.
Change-Id: I032815e23c69a8297c0a43992132441c240fb71e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
define CONFIG_PLATFORM only once in arch/Kconfig and set it
for every platform.
Change-Id: I8554bb36d2d15c3ee71fa63dfc3a763ebca956ee
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Saves an errno per-thread, retrieved via _get_errno(), instead of
changing the value of a global variable during context switches to avoid
a hit to the context switch performance.
Per-arch asm implementations are provided for maximum performance.
Enabled by default, but can be disabled via the CONFIG_ERRNO option.
Change-Id: I81d57a2e318c94c68eee913ae0d4ca3a3609c7a4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Removed old style file description and documnetation and apply
doxygen synatx.
Change-Id: I3ac9f06d4f574bf3c79c6f6044cec3a7e2f6e4c8
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch remove the dependency of the ADVANCE_POWER_MANAGEMENT
for profiling sleep events that was supported only for microkernel.
Allowing us to also use this feature in nanokernel-only systems.
Change-Id: I1761eb6c4d72f477b419dfca5dc152b0fb69ee27
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Setting up new platforms to handle emulation, and make them the only
ones able to run on QEMU from the Makefile "qemu" target to avoid
confusion with other platforms. We have now platform qemu_x86 and
platform qemu_cortex_m3, also modification to the sanity checks to have
qemu support only on those platforms
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Change-Id: I9291918a1d58fea4f37750ada78234628f9a5d98
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Since all the necessary bits utilizing UART by index have moved to
use device name instead, the uart_devs[] can finally be removed.
Change-Id: Idbae6b46c0af9eef6c22c59e121e9d6a6b52426a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use device name to find the UART device for uart_pipe usage,
instead of relying on an arbitrary index.
Change-Id: I36aaa4ed8f0b4905e4e741ca1464947e59f30869
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use device name to find the UART device for Bluetooth usage,
instead of relying on an arbitrary index.
The default device names being used are derived from the original
board.h for each platform. Some of them point to the same device
as UART console. Since this is a Kconfig option, the default
can be overridden so this is not a serious issue.
Change-Id: Ibe82f3968e72ba60f9c033aa3dfcb2fb3c41dc75
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use device name to find the UART device for console usage, instead of
relying on an arbitrary index.
Change-Id: Iebe01c9bf392dfee6d8284367f67647f7d47561a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove the call to uart_init(), and let the UART drivers take care of
the port initialization.
Change-Id: Id3e46135ab993cb6596b1fb5339ab1664c65ab40
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove the call to uart_init(), and let the UART drivers take care of
the port initialization.
Change-Id: Ibeca65b3fe64feb7a203a793c01c525ff5e6afda
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
() Renames stellarisUartDrv.c to uart_stellaris.c. This is to follow
the driver naming convention.
() Renames functions stellaris_uart_*() to uart_stellaris_*(),
following driver naming convention.
() Renames CONFIG_STELLARIS_UART* to CONFIG_UART_STELLARIS*
() UART ports initialization is moved into the driver itself.
All the init code in platform config files is removed.
() Adds (many) Kconfig options. These don't have to be defined
in each platform's board.h anymore.
Change-Id: I0eadc3878d69ff24d1637f8df5220fd2f161d24f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
() Rename k20UartDrv.c to uart_k20.c. This is to follow the driver
naming convention.
() Move driver/serial/k20_uart.h to drivers/serial/uart_k20_priv.h
as this contains definitions private to the driver, and
should not be exposed in public include directory.
() Rename functions k20_uart_*() to uart_k20_*(), following
driver naming convention.
() Renames CONFIG_K20_UART_* to CONFIG_UART_K20_*
() UART ports initialization is moved into the driver itself.
All the init code in platform config files is removed.
() Adds (many) Kconfig options. These don't have to be defined
in each platform's board.h anymore.
Change-Id: If1be1fde083aba6ff68062db2059aef08617a286
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Software interrupts or system calls aren't really appropriate for
zephyr, but we have an ongoing need in our test code to run a
function with arguments synchronously in interrupt context.
This patch introduces irq_offload() which allows us to do this without
separate initialization or having to manage fake IRQs in the
interrupt controller.
ARM assembly code contributed by Benjamin Walsh
<benjamin.walsh@windriver.com>
ARC is not yet implemented but will be in a subsequent patch.
irq_test_common.h has been removed and all test cases updated to
use the new API.
Change-Id: I9af99ed31b62bc7eb340e32cf65e3d11354d1ec7
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Put initialization priorities as device driver Kconfig
parameter.
Initialization priority value for each platform is defined
in the platform Kconfig file.
Drivers and platform code use SYS_DEFINE_DEVICE to add
and initialization function.
Change-Id: I2f4f3c7370dac02408a1b50a0a1bade8b427a282
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Avoid having to remove quotes wherever the platform name is used
by exporting the variable only once.
Change-Id: I4cb51901e4ac19d70d0310fe6bbacd157f586661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
They a) are unused, b) should not be in board.h, and c) are wrong on
ARC.
Change-Id: Ic40397d9cfcdf314544875f1443618865435d5e7
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
When building for a certain platform, we have no idea
what architecture we are building for.
We used to specify the architecture alongside the board or platform
name and this was used to find the defconfig in arch/<arch>/configs.
By putting all board configurations we support in one place we do
not have to specify the architecture, just the configuration name.
Change-Id: Ib7e9f63b9a8051714dc207f583fd26ef620497d8
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not depend on environment variables and use a kconfig variable
for defining the architecture.
In addition, remove the X86_32 variable, it just duplicates X86 for
not good reason, at least until start supporting MCUs with 64bit.
Change-Id: Ia001db81ed007e6a43f34506fed9be1345b88a4b
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not repeat the same flags for every added platform. Define
the common flags on the architecture level instead.
Change-Id: I0e501d6a909892dd682b106fb2a5072434a39563
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use CONFIG_PLATFORM to only build the selected platform. This
will enable support for drop-in platforms. Makefile will not need
to be changed for every new platforms.
Change-Id: I22778e8242422e487e941143df3e521b33f2b0a8
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move platform related data and definition to the platform
directory and include it using:
arch/<arch>/platforms/*/Kconfig.platform
This way we will able to add a platform as a directory of
content without the need to change and Kconfig files.
Platforms can then be included by reference (using repo or
git submodoules)
Change-Id: I6bff4e48490e33cbaf879fe3c424bf2f6a4887ac
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Original name was too generic and confusing. This patch renames
driver to pipe UART and moves it to console drivers folder. Kconfig
destription is also improved.
Change-Id: I716fdbf7d636bbdc03b0fce27a59fd866f473246
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
The driver should handle the initialization instead of relying on
platform initialization. This is to conform to the driver model.
Change-Id: Idc95d59bce2470b5118e416ee05f07548991a15c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Flags allow passing IRQ triggering option for x86 architecture.
Each platform defines flags for a particular device and then
device driver uses them when registers the interrupt handler.
The change in API means that device drivers and sample
applications need to use the new API.
IRQ triggering configuration is now handled by device drivers
by using flags passed to interrupt registering API:
IRQ_CONNECT_STATIC() or irq_connect()
Change-Id: Ibc4312ea2b4032a2efc5b913c6389f780a2a11d1
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
This is done from the kernel fragments, no need to declare it here.
(micro kernel is the default anyways)
Change-Id: I88511c03f44538cab3e8fbf8292e179e01005b0d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This was removed as part of some Diab cleanup, however it is needed
and without the definition we get the following when building
for the FRDM-K64F board:
arm-none-eabi-ld: warning: cannot find entry symbol __start; not setting start address
Change-Id: Ie0604a600b6f7a4faa321c58aa63c5617a163107
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In order to have a name according to the functionality of the feature.
This commit rename any text, function and variable related with the
Profiler name to Event logger.
Change-Id: I4f612cbc7c37965c35a64f06cc3ce5e3249d90e5
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
This was kept around since it used to be necessary for x86, and we
want our APIs to keep partity across arches, but with the x86 IRQ
refactoring this is no longer needed.
Change-Id: Iacd61f4c4d3cc33b4a15bfa083e106ba6d5da942
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Removing many of the typedefs that are only used once to lessen the
checkpatch warning about creating new typedefs. A handful have been
behind as they would require a more invasive change to the code. It
has yet to be determined if this is a worthwhile endavour.
Change-Id: Ibeb29e0a1d37e8121218fccf0d986cbebd226e85
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Only allow valid values to be set for this option.
Change-Id: I11dd7381ddbf6d4d9985255b9b784544074aba63
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The \NOMANUAL tag is a remnant from days of yore and is no longer
needed or useful. Cleaning up the code references to this.
Change-Id: I1b8cc9c9560d1dbb711f05fa63fd23386789875c
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Change-Id: Ie051000e3d3f0f5bdc330d0265010c37acb873bd
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change-Id: I34a54230bc4a63c8a4391d03ff530835910c3705
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change-Id: I819d13f0d7a23e3a61dcda6a3ced18810b192158
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change-Id: I6da43e41f9c6efee577b70513ec368ae3cce0144
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Moving many of the functions from the old format of inline comments to
the newer doxygen format.
Change-Id: Ib0fe0d8627d7cd90219385a3ab627da8f9637d98
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
These symbols are no longer required.
Change-Id: I99f6afad0ffb116efde1e2ff28252a2e4d8b7fb4
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Only driver specific public headers should be found in include/drivers.
All generic API are found in include/ directory.
Change-Id: Ic50931987bb9460fd4a3843abc6f5de107faf045
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Gets rid of the trailing initialization level character from the
name of the device variable generated by the macro, since it serves
no useful purpose. (The linker scripts place the various initialization
sections in ascending order based on the name of the section, so there
is no need to embed the initialization level in the variable name itself.)
Change-Id: I56bb79a513b8f77fb1f3fbaccec14454c2520772
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Change all the Intel and Wind River code license from BSD-3 to Apache 2.
Change-Id: Id8be2c1c161a06ea8a0b9f38e17660e11dbb384b
Signed-off-by: Javier B Perez Hernandez <javier.b.perez.hernandez@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Move Zephyr specific CFLAGS that depend on config options to
the Makefile where they can better be managed among other cflag
options.
Change-Id: Ia79a2f2def4f51857f6d661aa78e9fb7eb7a5e22
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not use micro_* or nano_* defconfigs, instead maintain platform
in one single defconfig and merge nano or micro support on top.
Change-Id: I0d5184f37865ed8312e516e48cf5a8584a287dfe
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
do not use microkernel or nanokernel as the output binaries,
instead, use zephyr globally.
Also change the documentation to reflect this.
Change-Id: I8405761d1a0392c90cdfeec5c67d72eb4e5a76ff
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
All supported platforms have descending stack (growth direction is
down). To avoid confusion just remove not needed stack direction
defines.
If new platform with stack direction up is added is should be
configured by adding Kconfig option eg STACK_GROWS_UP and
CONFIG_STACK_GROWS_UP should be used in code that depends on
stack growth direction.
Change-Id: I786ff1ab28d8f8bad3f6d1bbe64defc0e81d1707
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
There are devices that need are part of the architecture core the need
to be initialized prior to devices that are integrated around a core
to make up a complete SOC. Namely the interrupt controller in the SOC
must be configured in order to allow the integrated IP blocks drivers
to initialize correctly.
Change-Id: I0a91e08f98516a7b7dd402ffc6494a071f1326b2
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
This macro is legacy from an early implementation of the init system
before the pure level was split into early and late phases remove it
now to avoid confusion going forward.
Change-Id: I6720874c840c9e14888fd6f411a8182e7420ca29
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
In the future there will be no need to deal with such updates anymore.
Change-Id: Ib66b826f054f444ccb8f7e6f0e6a31e8d93f342f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Put architecture option and ARCH_DEFCONFIG on the top
and simplify default options for the architectures.
Change-Id: I4cae73f3e9ec24913e201269ec6dc8eddc2fd7c1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Follow the model of the Linux kernel for adding arch
specific CFLAGS by using the Makefile and Kbuild combination
in the arch/<arch> directory.
This will also allow adding architecture specific targets and is
easy to maintain when alongside the architecture.
Change-Id: If51a78e8845baa71d9090c4a4f49fcd013354840
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename field 'Args' of the struct:
- 'k_proc' in the file include/microkernel/base_api.h
- 'k_args' in the file kernel/microkernel/include/micro_private_types.h
Change-Id: I5847a2f1e9c7dd34dea37857b4fadeb37ced489b
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Rename field 'Ident' of the struct:
- 'k_proc' in the file include/microkernel/base_api.h
Change-Id: Iec787e0a8aa1791c968b371017cf96211a60cef1
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Add the sleep events point for x86 and ARM arquitectures that gives
information about when the CPU went to sleep mode, when it woke up
and which interrupt causes the CPU to awake.
Change-Id: Iaa06a678eab661357d084ee1f79c4cfcf19bf85d
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Add the interrupt profile points for x86 and ARM arquitectures. This
gives information regarding the time when interrupts occur.
Change-Id: Ic876c0e7f9e8819d53e0578416f09146f4456d3d
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Also for ARC, rename context_wrapper.S to thread_entry_wrapper.S.
Change-Id: I83318ae352a688996f8436cf3252f6108ec23dc5
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Somewhat useful utility that should only have one implementation, so it
can impede on the normally-available application namespace.
Change-Id: I085850177c231fdf58634f97e897c4d2e1a5cffb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The term 'context' is vague and overloaded. Its usage for 'an execution
context' is now referred as such, in both comments and some APIs' names.
When the execution context can only be a fiber or a task (i.e. not an
ISR), it is referred to as a 'thread', again in comments and everywhere
in the code.
APIs that had their names changed:
- nano_context_id_t is now nano_thread_id_t
- context_self_get() is now sys_thread_self_get()
- context_type_get() is now sys_execution_context_type_get()
- context_custom_data_set/get() are now
sys_thread_custom_data_set/get()
The 'context' prefix namespace does not have to be reserved by the
kernel anymore.
The Context Control Structure (CCS) data structure is now the Thread
Control Structure (TCS):
- struct ccs is now struct tcs
- tCCS is now tTCS
Change-Id: I7526a76c5b01e7c86333078e2d2e77c9feef5364
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
There is no concept of a "process" in the system, so remove last
mentions of that concept from free-form text (doc, comments, macro
parameter names).
Change-Id: Ic1b73371c448ed93b0db46bc9bb412d1e1dbc8bd
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This commit fixes an issue with INIT_STACKS configuration option.
k_memset is substituted by the libc memset routine to initialize a
block of memory.
Change-Id: Ic3e286d0976f618110b2828f6da76417b868aef0
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
The initialization procedures need to be called in the
following order:
- basic hardware initialization;
- devices initialization;
- hardware clock initialization, that the kernel needs to
run the kernel server.
This way, the board initialization routines is placed
to the pure_early_init level to make sure it runs first,
all device initialization procedures run at pure_init level,
so they are initialized early enough to be used for debugging
if needed. Hardware clock initialization is placed on
nano_early_init level to make sure hardware clock is initialized
just before the kernel server starts.
Change-Id: Ieecf9f0252c47c621b7208969687dc1113fc2ad0
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The board runs with 120 MHz CPU frequency, the systick
uses CPU frequncy. This way 120MHz is a correct value.
Change-Id: If47f1ce6371fb7202ececb4d5f8f7c984aa66598
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
This is just a cosmetic change to unify anything interrupt related
under 'irq'.
Change-Id: Ib8804d194e11eb49526fda952d9efc0f2ffac2df
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows the serial driver to be excluded from the build.
Change-Id: I74549b058d85bf35acf9d719643139901ae5973e
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows the serial driver to be excluded from the build.
Change-Id: I1be0ee5bc6817ac03ed23dcc9925cff1b694d584
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Move the baud rate selection for uart_console into Kconfig.
This allows apps to specify custom speed. Default is 115200
which should be supported by almost all RS232 and USB adapters
out in the past few years.
Change-Id: I78649bf2a1b2ddfc90a20d611a6454e3ad3b1b3a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is the final step to convert serial to the new driver model.
The dev->driver_api is now being used by individual drivers.
As a side effect, it is now possible to build multiple serial
drivers in the final image (though it won't make much sense).
Change-Id: I5d864e6503a5431b29006c311320155adf81cf5b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This introduces the config option CONFIG_UART_CONSOLE,
and also CONFIG_CONSOLE. The UART console can finally
be disabled if desired.
The defconfigs are also being updated.
Change-Id: I5ebaf6471986deca105971e67fcddb43374de94a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
With this, the UART console has its own initialization which is not
dependent on UART init routines.
This will allow the app to utilize all UARTs for other purposes,
instead of always reserving one for console. Future patch
will enable this choice.
Note that the console init is effectively demoted to pure_init
from pure_early_init. The UART console depends on UART being
initialized, but there is no deferred init at this point.
So this initializes the console a bit later than UARTs,
simply to make sure the UART is initialized before using it.
Once there is a mechanism for some type of deferred initialization,
the UART console init can be promoted back to pure_early.
Change-Id: Iba95197b13384cb1a46e34c78638348b7a0bec8c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This restructures the device structs and now utilizes the new
driver initialization model. This is another step towards
converting the serial driver to the new driver model.
Note that the serial driver does not initialize the hardware
unless it is being used by another driver. The configuration
of the serial port needs to be done by the driver utilizing
the port (e.g. baud rate, interrupt priority, etc.).
Therefore, some serial ports are declared but not exactly
configured.
Also note that the UART console is being initialized at
the same time as the serial port. This will be removed
in future patch, so the UART console driver will do
its own initialization.
Change-Id: Idd89954b2d0649a557ba8c869ee96512fec898e4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This encapsulates the whole serial drivers Kconfig sections, and
allows the whole section to be deactivated.
Change-Id: I84f8d35da74f3c00a44d8c17786ea2297422d68b
Signed-off-by: Daniel Leung <danielcp@gmail.com>
This moves the static device definition from the driver file,
drivers/bluetooth/uart.c, into the platform config files for
each platform.
This is another step towards converting UART drivers to
the new driver model. Also, platform config files are a more
logical place for the definition.
Change-Id: I668a52de5a38005b8b2bcb67d74437ead377cb16
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
... instead of an array index to a global array. This is
an intermediate step to make the drivers conform to
the new driver model.
This only changes from using a direct array index to using
device structs. The UARTs are still staticlly defined.
Later patches will make the drivers utilize the driver
initialization procedure specified by the driver model.
Change-Id: I18041bbb4b0efdf8ae87088fd000b391d0827e9b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The new names reflect better what the functions do: they find the first
bit set starting from the least or most significant bit, i.e. they find
the least or most significant bit set, in a 32-bit word.
Change-Id: I6f0ee4b543f6f37c2f08f7067e14e039c92a6f6a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The inline versions are renamed to remove the _inline suffix, and the
non-inline versions are removed from the code base.
Change-Id: Iee2e6adcfb5da1fe0a978a05aa854e10ae82a8b8
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The inline versions are renamed to remove the _inline suffix, and the
non-inline versions are removed from the code base.
Change-Id: I7314b96c42835f15df4c537ec11ab7961d4ee60f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Standardize on using the irq_lock/irq_unlock (non-inline) symbols
everywhere.
The non-inline versions provide absolutely no benefits, so they will be
removed in a subsequent commit, and the inline versions will have their
_inline suffix removed.
Change-Id: Ib0b55f450447366468723e065a60adbadf7067a9
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Align with the newer terminology used for microkernel internal symbols.
Change-Id: I623b383f90d9e37a49429a79774c7f7a4953bd5f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
irq_handler_set, irq_priority_set and irq_disconnect have been made
private by prepending an underscore to their names:
irq_handler_set -> irq_handler_set
irq_priority_set -> irq_priority_set
irq_disconnect -> irq_disconnect
The prototypes have been removed from header files when possible, and
extern statements used in C code where they were called.
_irq_priority_set() for ARM is still in the header file because
IRQ_CONFIG() relies on it.
Change-Id: I2ad585f8156ff80250f6d9eeca4a249a4477fd9d
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Add the context switch profile point for x86 and ARM arquitectures.
Change-Id: Ib7205059104ed47b96ba75b8cfefec3ff35f6813
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Add a standardized mechanism to add profiling points to the Kernel
with a single interface for the user to collect the profiling data.
Change-Id: I4fa34ac1b42f73a73ba1fd805e755ee2fd00dff7
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Add a log event tool with a single interface for the user to
add/collect the event log data.
Change-Id: Ia4b78836748c5d7e44ba1bdd50c28434e8a55d65
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
The name of the device is SYSTICK. The device name should be part of the
file name, like all other timer drivers we support. The name
'cortex_m_timer' said nothing about which device the driver is for, since
it's way too generic: it could be for any timer present on any Cortex-M
board.
Change-Id: I39b4f79c32516ec9aff82c55c0ca639fad1b52bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This change removes the internal number-to-function mapping
of microkernel services. Instead, function pointers are used
to specify which service to use.
This is in preparation for private kernel objects. Before this,
only kernel objects that are defined in MDEF files would have
corresponding functions included in the final binary, via sysgen
by populating an array of number-to-function mapping. This
causes an issue when a certain type of objects are all defined
with source code, and never in MDEF file. The corresponding
mapping would be deleted, and the functions are never included
in the binary. For example, if no mutexes are defined in MDEF
file, the _k_mutex_*() functions would not be included.
With this change, any usage of private kernel objects will hint
to the linker that those functions are needed, and should not be
removed from final binary.
Change-Id: If48864abcd6471bcb7964ec00fe668bcabe3239b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The Kconfig option PROT_MODE_SWITCH_PROMPT was being used to conditionally
display the "Boot Sequence Options" Kconfig menu. It is simpler to include
both PROT_MODE_SWITCH and its dependent BOOT_A20_ENABLE in the parent menu.
However, doing so necessitates that the name of the parent menu be changed
from "Bootloader Options" to "Boot Options".
Change-Id: I9b9a074a0d4ec5209f5349b42178409c73875b00
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removes references to obsolete BSP terminology. Where appropriate, replaces it
with platform terminology.
Change-Id: I26c199c50fefc9729ec07c48083bedc86890cc89
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Replaces references to obsolete BSP terminology with platform.
Change-Id: Ibd083558bbbb08a16a68d58251774fb4c84cbbf8
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The Kconfig option SW_ISR_TABLE_BSP is not used anymore.
Change-Id: Ifc1be395f5ed7e5d1072a783d800385e69fbc4dc
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The configuration of SRAM and flash options are no longer hardcoded in the
platform's linker script file, but are instead defined in the platform
configuration file.
Change-Id: I557a8228080d607f6add5f86b9b2509ed3fd31ce
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds Kconfig options for specifying the following platform attributes:
SRAM size
SRAM base address
Flash size
Flash base address
This will allow them to be hoisted out of the platform's linker script file
in a later commit.
Change-Id: I09ba5c09d8f34eea5d787c669d77d27d4389d824
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The Cortex-M related Kconfig menus and options no longer show up at the top
level when "make ARCH=arm menuconfig" is issued. They show up under the
"General Platform Configuration" menu.
Change-Id: I6bf012e628212340f5e089d0193a9a71d90c79b9
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Eliminates bsp directory as part of transforming BSPs to platforms.
Change-Id: I8b5366bf32797ddbb1bfa3520ddfeed6344cec2f
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Fixes whitespace issues found by checkpatch.
Change-Id: I0bfa6721dcf2d6c0413b4ca39d3c5ea98631b96d
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Renames supported platform configurations to conform to new platform
configuration naming scheme.
Example usage with PLATFORM_CONFIG:
make PLATFORM_CONFIG=basic_cortex_m3
make PLATFORM_CONFIG=basic_atom
make PLATFORM_CONFIG=basic_minuteia
make PLATFORM_CONFIG=galileo
xxx_ti_lm3s6965_defconfig -> xxx_basic_cortex_m3_defconfig
xxx_generic_pc_atom_n28xx_defconfig -> xxx_basic_atom_defconfig
xxx_generic_pc_minuteia_defconfig -> xxx_basic_minuteia_defconfig
xxx_quark_defconfig -> xxx_galileo_defconfig
Change-Id: I696eb8b9ad9a72d7a72efbe1341ce23500335764
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Updates Kconfig option names as part of transforming BSPs to platforms.
Change-Id: If397bcac8b058e5700e82c3cabbfe64588316d1d
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
As a step towards eliminating the ARM's bsp subdirectory (as has already been
done for the x86 arch), the contents of 'arch/arm/bsp/Kconfig' have been merged
into 'arch/arm/Kconfig'.
Change-Id: I813b5c9e19187347147875635deb851a3357dd55
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Moves (and renames) sysFatalErrorHandler.c out of the 'bsp' directory and
into 'core' as a step towards removing the directory 'arch/arm/bsp'.
Change-Id: Ie10aa2099f07380e4583dbbd32cdda917b4999ba
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Change the function signature of _InitHarware() function and rename
the function to a platform specific name now that it will be called
via a function pointer and not by name.
Call the platform *_init() function at PURE_INIT time.
Change-Id: I5168dfea81f406da135d491a2b4a24e8255f418a
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
This commit removes 2 levels of checking and checks directly against
define Kconfig variables. Also reduce the code to one block and check
only once instead of twice.
This is a cosmetic change.
Change-Id: Ia427d9f15a9d09ea59d0230913168060d752ae99
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Since SysGen generates the code to invoke _sys_clock_driver_init(), the build
system no longer needs anything from the config1p.mdef files.
Change-Id: Id22615ff137c9d146ccc5c3777a75b2d3bfee73a
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Remove function name from comment and add @brief instead.
Also capitilize first letter.
Change-Id: Ib708b49bf02e5bc89b0066637a55874e659637e0
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Previous comment style used RETRURNS:, use @return to comply
with javadoc style.
Change-Id: Ib1dffd92da1d97d60063ec5309b08049828f6661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The change replaces multiple asterisks to ** at
the beginning of comments and adds a space before
the asterisks at the beginning of lines.
Change-Id: I7656bde3bf4d9a31e38941e43b580520432dabc1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is helpful when working with UART through dynamic
interrupt stubs.
Change-Id: I91d64f575aa755fcfd894d678a1c078219447f16
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Use Kconfig to define this variable and remove its
previous definitions from board.h. This will simplify
creation of different variants from a single platform.
Change-Id: I0aaa5aa81dedf096c6d8c1ea2d509c71817336d3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Moves the Cortex-M timer driver so that it resides with the other timer
drivers.
Change-Id: I3324c53356efd9f5fd88752a98e4ae301ea38d47
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds the Kconfig option for selecting the Cortex-M systick timer. This helps
pave the way for moving the Cortex-M systick timer into the drivers/ directory.
Change-Id: Iee040083a425c9c1dbc5973991b89239e0a72eee
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The new name indicates that the ARM systick driver is specific to the Cortex-M.
Change-Id: I43a9e5f467b83cb6050356419089d8f4da42c589
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Updates references to CONFIG_BSP_DIR to CONFIG_PLATFORM as part of the
BSP -> platform clean up.
Note that despite the renaming, the usage of the config option remains
unchanged.
Change-Id: I2846c3f761cf09871019c0855bf1824ae03e6b3c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The following directories do not exist:
$(srctree)/include/bsp
$(srctree)/target/src/bsp
Change-Id: I27990cc404502d96e323df8b95e1ac105e6d5265
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
also change Zephyr OS to Zephyr Kernel.
Use a script to check and update all default configurations.
Change-Id: I9614d698fd5b7c803590e83a7429403357c09a94
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The revised name better reflects the fact that the file defines
macros in addition to declaring variables. In addition, most of
these APIs use the "sys_clock_" prefix, which aligns well with
the new file name.
Change-Id: Ib33517d4b19ec2455303b87200c677e87640fcbc
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Eliminates unnecessary "offsets" subdirectory, and aligns file
name with gen_offset.h which resides in the same directory.
Change-Id: I8cea3bc54b5ceae3091d4a5c77c59ab826339f75
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Eliminates use of non-standard camelCase file name.
Change-Id: I809de5f72b40adfd49cbc128992de934e3ec66e3
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Gets rid of "nano" prefix on these nanokernel files.
Change-Id: I78c4dd4ebbbbd91f6fdd4e54ffc82de9bd232c7d
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
The new name better reflects that this file contains all private
nanokernel APIs that are used by various kernel subsystems.
Change-Id: I4c258d582e93753eec9e575fdb5f9f2109417a0f
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
The new name better reflects that this file contains all private
microkernel APIs that are used by various kernel subsystems.
Change-Id: I5e52172a9e33aa130ce55ce59e887bba5c1c175a
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
The new name better reflects that this file contains private
microkernel APIs (types, structs, etc.) that are used by various
kernel subsystems.
Change-Id: I7a89be893455b3daaf30baa40a0ec8e0cde7cc36
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
IRQ_CONNECT_STATIC() macro provides static interrupt registration.
It creates an entry for _sw_isr_table, table of interrupt handlers.
IRQ_CONFIG() macro provides interrupt controller configuration.
On ARM platform it configures the priority of each interrupt.
_sw_isr_table is implemented the way that each of it's elements
is located in individual section. Sections are marked a "linkonce",
thus when a device driver declares an interrupt handler, it overwrites
the default _sw_isr_table entry.
Change-Id: I182bf7158dd67f45b597783dca038a4f78166a03
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Makes the ARM CPU type a choice between CPU_CORTEX_M3 and CPU_CORTEX_M4
(similar to the choice of processor for x86). This completes the breaking
of the forced selection of CPU_CORTEX_M3 when CPU_CORTEX_M4 chosen, thereby
making CPU_CORTEX_M3_M4 the true umbrella option for the Cortex M3/M4
processors.
Change-Id: I1d1f39352d85a5848b13102ceb8365c7dede0959
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Makes name more consistent with other CPU_CORTEX_M* options.
Change-Id: I65968cb300207ba0de6231d9a67f2720be77b6ba
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Makes name more consistent with CPU_CORTEX_M3_M4 option.
Change-Id: I6f0a14322b7774df54a3459f91cd3acf07819b04
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Makes name more consistent with CPU_CORTEX_M3_M4 option.
Change-Id: I0b89a50a5c0b728167cd76219d25ddf98243c0dd
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
CPU_CORTEX_M3_M4 replaces CPU_CORTEXM3 as the umbrella option for Cortex M3/M4
processors.
NOTE: Selecting CPU_CORTEXM4 still currently forces the selection of
CPU_CORTEXM3. Breaking that forced select will be done in a later commit.
Change-Id: I0f36b3a2adc5c6c66db4e9b6353b921199544deb
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The type of the handler variable was missing, causing compile failures.
Change-Id: I33c0f8d2893de0c6ad14f33ecb03b106c87cf758
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
s_NANO contains the timeout queue, and each ccs needs a struct
_nano_timeout object that gets linked in the nanokernel timeout queue.
Change-Id: Iad027eaaebcffe190e95f0b9d068f047062559c2
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This commit set back .S as the assembly code extension for Kbuild.
Change-Id: Ib0119876bd0bed6617bbfbad2ca6a44e172ab042
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
- Use Zephyr OS instead of Tiny Mountain
- Update with latest config options and values
Change-Id: I64084c37ce28b25587462468de86e4a904749433
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Since the system generator pre-registers K_ticker as the handler
for the system tick event, there is no need for the timer driver
to re-register it at run time.
Change-Id: I7f20c19e5c6ccc7dfb6117aa2d2647b9dec0e549
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
This driver is a very simple UART driver that can be used to implement
a protocol in application. It has no protocol logic and just allow
application to receive and send data over UART in platform independent
manner.
API is designed to minimize number of required memory copies.
Application is able to provide new buffer every time it decides to
consume received data. It is also able to just alter offset and
reuse current buffer eg if data was corrupted or otherwise invalid.
Change-Id: I8d3827fe2e242196e986d0419bc5487357481558
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
The file extension indicates a "Microkernel DEFinitions" file,
and no longer reflects the obsolete VxMicro/Viper branding.
Change-Id: Ib95b271404a4a4737e851d603c371244fa609e4d
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Eliminates references to the obsolete OS name. In most cases the
name is simply removed, as it isn't necessary.
Change-Id: I32f9e7390e436aec008a9454b72657e129d65152
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Eliminates duplication of these entries by the various architecture-
specific include files for private nanokernel APIs.
Change-Id: I711c3b42fe375d1574ce4a540142c3b507b71557
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Introduces nano_internal.h, which will declare all architecture-
independent non-public nanokernel APIs. This file is automatically
incorporated by the various architecture-specific include files
for non-public nanokernel APIs, and will not normally be included
directly by any other files.
Change-Id: I9f3de812a5747cc720fa0ff739007315e8d07dd9
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
1) Renames routine to conform to kernel naming conventions.
2) Relocates routine declaration to include files for
non-public nanokernel APIs.
3) Relocates routine definition so that it resides with the
nanokernel's other fiber manipulation routines.
4) Eliminates an unnecessary argument to the routine.
Change-Id: Ia139280dfea36262ca8417708786b4989f3eaee1
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
These now appear in the files which declare other non-public
nanokernel APIs.
Change-Id: Iea01d6de44851a08b308004b2c3104c08b020970
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Gets rid of places where there is no need to include these files
at all, or places where these files are being indirectly included
due to the inclusion of nanokernel.h.
Change-Id: I7b58148af454b977830c00a6b519a78d0595603b
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
This commit add the symbols CONFIG_RANDOM_GENERATOR
to the default configurations.
Change-Id: Iff0e5a7d144993bf1cc9967bcffff037333cdf30
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Gets rid of single-line comments required by a previous set of
coding conventions. These comments provide no value to readers
and just clutter things up.
Change-Id: I2a08b12cf5026253de56979efdfc510e7e68defe
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Instead of initializing the stack (when INIT_STACKS is enabled) in start_task()
and _fiber_start(), do it in _NewContext(). This helps to both reduce code
duplication AND ensure that all contexts get an initialized stack (previously
the background/idle task's was missed).
Change-Id: If2d50309d2be48fac937f5d0ae96b9de185c0fe2
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
This commit sets Execute in Place (XIP) option
as a default for CortexM architectures.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: Ib9bd361a9ac6c64d9755c6bf3ac5c8df6c1b22f2
According to section 3.7 of Documentation/kbuild/makefiles.txt, using
EXTRA_CFLAGS in Makefiles is "still supported but their usage is
deprecated." However, using make EXTRA_CFLAGS="-DSOMETHING" results in
EXTRA_CFLAGS from Makefiles being overwritten, obviously breaking the
build. This patch converts to them to the newer ccflags-y which also
fixes the problem.
Change-Id: I6309439599d4c9cc184f9ecd941bde841982ef07
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Since the address of the new context is known before _NewContext() is invoked
(due to it being passed a properly aligned stack), there is no longer any
need for _NewContext to return the pointer to the context.
Furthermore, as a direct result of the properly aligned stack, the pointer to
the new context does not need to be passed as a separate parameter since it
will always match the passed stack pointer.
Change-Id: Ie57a9c4ad17f6f13e8b3f659cd701d4f8950ea97
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Runtime alignment of a context's stack is no longer necessary in _NewContext()
as the memory is aligned (via the __stack tag) before calling _NewContext().
Change-Id: I31b7fd883ea3f1dcdb378e8ff508430bc75afcde
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The __attribute__ keyword is toolchain specific.
Change-Id: Ia3c0ff54d778785679c864704f8db6a3ba898948
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
This reason code will be used indicate that the kernel failed to allocate a
critical resource (such as a command packet or a timer packet).
Change-Id: I6d4c3d96fc70b2b8cab4027b1b8e4febf4d6c474
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
This is not required since the secure string library routines
have been removed.
Change-Id: I284a21e4167d9bb6f78354d809c563a4c52f619c
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Renaming the directory include/nanokernel to be include/arch, which
better reflects the real nature of the directory and the contents
inside.
Change-Id: I2bc33ebc6715e2f0403227a558279fdf52398ade
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Renaming the CONFIGRUE_UART_PORT macro to UART_PORT_CONFIGURE.
Done to better align with the current naming process, but also to
remove some possible confusion over the macros source now that
the tree has moved over to Kconfig/Kbuild options.
Change-Id: I1a7691d09818c3d529de346e7fa347ce5ac19aed
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Remove ARM specific driver that duplicates the platform
independent one.
Rename x86 specific driver to make it unique.
Added configuration options for random and non-random
number generators.
Change-Id: Ie1b277d2927cdfe877650ae09134db7c86becb76
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Follow common practice and use standard dynamic irq connect mechanism.
Change-Id: Ibb29858da77909ede1fe2dacb056274e49687473
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Board specific headers should be included conditionally based
on the selected BSP.
Change-Id: Ia8c32c56e94670f4c59f7acac28557dd178e44f1
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
This commit add license headers to Kconfig files.
Change-Id: I79e60263b8c7b696463ecc84b8ad411af5415117
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit adds the Makefile and Kconfig files
to support the bluetooth driver in the Kbuild system.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: I1f72b13aca8fb098eece04c4f0e1b680639b520f
We need to always build nmi.c for ARM, this should not
be conditional on RUNTIME_NMI.
Change-Id: I27c0cb07b3f63eddd2141d07cb988548ef0050ec
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
$(srctree)/kernel/common/bsp does not exist anymore,
remove it from CFLAGS
Change-Id: I948ed9aa97469498a803916060935deb7a1a0271
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
TiMo is very ambigous, be generic and call it kernel.
Change-Id: I66b3e436afbc89e874f31a89b98cc04aa821c787
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit update the defconfig files for the arm
architecture with additional Kconfig symbols.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: Ib9bbde65ae333387cebf63949b7a2e9275489f35
This commit adaptes the Kbuild system to the change of location of
the header files for drivers.
Old location: driver/
New location: include/driver/
Change-Id: Ic49d373149ee44d781419c5c68e59408c8ef1c11
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit add support to the Kbuild system for the
NUM_TASK_PRIORITIES Kconfig symbol and the corresponding sysgen
parameter.
Change-Id: I6b035437c86d62f72c25d696d18182a7b0448e8f
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit fixes issues to allow build on ARM architecture.
- It fixes the include paths in Makefiles.
- It fixes the include path for the offsets.c compilation.
- It fixes the linker command. This changes is needed because gcc
ARM cross-compiler does not accept an AT() command without
specifing an address explicitly. This corner case appears
on ARM architectures when XIP is disabled.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: Ief8b53c4cc154abba7b7827121ec5a56f62b7b26
This commit removes the Kconfig symbol KERNEL_DIR.
The symbols was no longer needed because sysgen is only
used on microkernel architectures and the value of
KERNEL_DIR is always "ukernel", therefore it is redundant.
Change-Id: I5e38dd431c5b6f7586e8b25aea330632e96f581f
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
This commit adds the defconfig files that define the standard
configurations for x86 and arm architecture and the standard
configurations for the following BSPs for microkernel and
nanokernel:
- x86 generic pc
- x86 quark
- arm fsl_frdm_k64f
- arm ti_lm3s6965
They can be applied using the make target defconfig.
This target will generate the corresponding .config
file that will be consumed by the build system.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: I128ad52f792eeb61cc80578be5fc3bd427447aaa
This commit creates all the Makefiles that describe the object-
bundles for the arch directory and every sub-directory below.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: Icb4ebcfc430a132e514507149ad5ab6878eeed64
This commit adds the Kconfig files that describe the CONFIG
symbols that belongs to the arch directory and subdirectories.
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
Change-Id: I744225ddaa5e2b45113ca049457a8f9925ebe4c2
Now that UART drivers are configured internally when it comes to
hardware specific information such as IRQ and registers (or mmaped
registers), bluetooth UART driver no longer needs to do it by itself. It
only requires to select the port it wants to use.
Change-Id: I5a30500f4b6f4155292609d0ed4a758f91930817
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
UART is configured statically into the driver directly and not anymore
in the board's system.c. Thus limiting the information to be scattered
into 2 files instead of 3. Then in future, it will also be possible to
remove driver specific informations from the generic UART API structure.
Change-Id: I001f2a6834df9a41ab395a80e4e39b347d545db3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Not only is __start is a neutral label, but using a common entry point for all
architectures allows the entry point to be hoisted out of the linker script and
specified by the build system.
Change-Id: Ibcbb11a40ff964e0fc3c90afcfe231746071b040
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Renames the include file defining non-public microkernel structures
from k_struct.h to kernel_structures.h, and relocates it to the
microkernel's non-public include file directory. This means that
applications and drivers including the microkernel's public APIs,
using microkernel.h, can no longer access non-public information.
Note: This change also eliminates some redundant #includes by the
microkernel's own subsystems, since the inclusion of minik.h brings
in the vast majority of public and non-public APIs.
Change-Id: Ic7d9ec1ebb8a124ccd0aaad98b50e16c197ffa00
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Replace duplicate code and will allow for further cleanup by possibly
consolidating micro/nano code that is currently guarded by preprocessor
conditionals.
Change-Id: I9aa9966c581244646b6ea317ef8b51fef9054dd4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Updating global variable's name to follow a consistent naming convention.
Explicitly moved from __ to _ by direction of Ben Walsh
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Idd6f7c3c2fdd818f0a794985f3689705cac3c0a2
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I4f0c65fb93cfac7d91d89c034a4bccd46d33a2f0
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I42d80495508656c8476b5538fbd4af7a7569e8d6
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ie65865c480be5b6a678ef4716dade3ee745bd88f
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Icb3f7d66e94bcf1aa8dec5cc76257b6095c19d56
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ie5ecf994d2e7e16a0e223fa64355274f6f0ad42e
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I247a19e520307d90a5742c85bf3cf6f04cb28c3b
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I6737b01f427d83b4bf1bc486ef0706fac0db0a31
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ide570aba204fdb7098bbe0f57ee7bbeaa436951d
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ie986b037f03264f4447b2bb4375ddcff91668633
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ia4f7d944464225d6ff1977a559637a5a0d61c0d5
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I8f886c03823f071edb90b297c290cc6f432a4565
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Id3f9096f28a1bf98035c6a531cd8d2dc66e6448a
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I7fc572f869c5f104538cfb3f84b1b36071e54dde
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Icf5900c057f3412d3c7725c07176fe125c374958
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating local variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" -o -name "*.arch" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I80ccb884f1ffd8f3740cd9298787462485b08024
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
In order to have a better compiler support consolidate
inline assembler code in a set of header files.
If another compiler is used, that supports a different
inline assembler format, asm_inline_<compiler name>.h
heder files have to be provided.
Change-Id: Iecc7d96419efd767a8463933badd4db4a557de5b
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Moves all files in this sub-directory to kernel/nanokernel, then
deletes the sub-directory itself. Both of the relocated files are
associated with fundamental nanokernel capabilities, which makes
their inclusion in the main nanokernel source directory logical.
Change-Id: Ifae46a50c60f67e9226d3a33cd0086b644b291ba
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Moves all files in this sub-directory to kernel/nanokernel, then
deletes the sub-directory itself. Both of the relocated files are
used during nanokernel initialization, which makes their inclusion
in the main nanokernel source directory logical.
Change-Id: I1cac0561317f808eab2de74ece9868c62c70b6d8
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Moves all files in this sub-directory up one level, to the main
nanokernel source directory, then deletes the sub-directory itself.
This change means that all nanokernel source files (with the
excecption of its include files) are now in the main nanokernel
source directory, which is a more intuitive arrangement.
Change-Id: I6bd4b1bb6fdd9be13d57b320947f520a5bc73914
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Relocates start_task() so that it appears in the main microkernel
directory, alongside its complementary routine abort_task();
this corrects a long-standing anomaly in which this microkernel-
specific routine appeared in the nanokernel portion of the tree.
With this move, the start_task.c file and its parent nanokernel/task
sub-directory no longer serve any purpose and are removed. (Note that
no changes are required for ARC architecture support, which does not
support microkernel capabilities and doesn't use this sub-directory.)
Change-Id: I973e1c32c9a8ddcacdc08159069ae7cdfea0f107
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
This allows to build Bluetooth for the target.
Change-Id: I89b1c369d698ee20d0b190614d7f3a9f686f7a5e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Support following configurations:
- With SW ISR table (CONFIG_SW_ISR_TABLE=y)
- static (CONFIG_SW_ISR_TABLE_DYNAMIC=n)
- dynamic (CONFIG_SW_ISR_TABLE_DYNAMIC=y)
- Installed directly in the vector table
(CONFIG_SW_ISR_TABLE=n)
Change-Id: I8562504366295c63202a387c12a2f99f4f1b3dde
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
For fsl_frdm_k64f target add definitions for Bluetooth UART.
Change-Id: Ib1f036aa29ae8709a67016180639d7130a352777
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Support following configurations:
- With SW ISR table (CONFIG_SW_ISR_TABLE=y)
- static (CONFIG_SW_ISR_TABLE_DYNAMIC=n)
- dynamic (CONFIG_SW_ISR_TABLE_DYNAMIC=y)
- Installed directly in the vector table
(CONFIG_SW_ISR_TABLE=n)
Change-Id: Icbaf710fcd8ed8dba409c144cf25849985270a64
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add Bluetooth UART driver to build targets.
Change-Id: Ia79b69a996bf79b24672bf1e0350e3de171ac409
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add Bluetooth initialization for target ti_lm3s6965.
Change-Id: I7c7e392d2bb8671098e54b1305051a5882fd3bef
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add definitions for UART for ti_lm3s6965.
Change-Id: If7b3d6f0cabd69eaad962b5e73429b66d1f0ef0e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Only moving the header from drivers/console/uart_console.h to
include/drivers/console/uart_console.h so source file did not need to be
changed, only the defs.objs files to look into include/drivers/console.
Change-Id: I585e16b50d9ffecf01ca9225e80f0e101f62ee4c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Renaming camelCase _SpuriousIRQ makes code more readable and
consistent.
Change-Id: I2bda4d107091384811d9f9187f3529960842631e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Instead of calling directly isr call static wrapper with right
_IntExit() at the end.
Change-Id: Ic5ca74200be6477837bf6a25803540990e9e8889
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add support for fsl_frdm_k64f configuration with
CONFIG_SW_ISR_TABLE_DYNAMIC and CONFIG_SW_ISR_TABLE. Entry for serial
irq is removed from vector table to be handled is ISR SW table.
Change-Id: I03b2a6f71aab09660587a290a0e69bdac67ef66c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add support for ti_lm3s6965 configuration with
CONFIG_SW_ISR_TABLE_DYNAMIC and CONFIG_SW_ISR_TABLE. Entry for serial
irq is removed from vector table to be handled is ISR SW table.
Change-Id: I6bda7a541aad979e4a50beb9154bbeb3758b48ee
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Rename camelCase uartConsoleInit function for consistency with the
rest of the code in serial console.
Change-Id: I519737070538e9c0f52a8d110a3eff68e0185ce2
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Following comments received during review rename console_uart_isr to
uart_console_isr for consistency reason.
Change-Id: Ibee1dec40ee19a9095f78969a07ffb73518fffbb
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Modifies the name of this field to make its purpose clearer,
and to align with coding conventions.
Change-Id: I8de78df1a0459122067d650130e01078afb5af8a
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Revises code that was previously conditional on HOST_TOOLS_SUPPORT
but is now conditional on CONTEXT_MONITOR.
Change-Id: I78a9126c5a66128f5aafe6b4220b3c7c68e01335
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Revises this option to make its purpose clearer, and to align it
with other experimantal monitoring-type configuration options.
Change-Id: I593bb7560b5a0544eb05affaa07b59dd78ea907e
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I4e5c9419fe0ccbc4b2990b96fc95c697decc18e0
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ide44a5957321a1dd2971a341da2d35dfb1e0d0ac
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I5e249e34ee9666666e31db6b9f71fe2abcc22400
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ic81b4ad7edf476da61ae62df627866e0446714d7
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I2e501394b7fa4264d9854659e2dd008e5c94b540
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Iebefec0e02cbb838564dd71fd4424c1adbff31f5
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: I36709c9833279f05a186a5c00b996d242c843d4c
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating global variable's name to follow a consistent naming convention.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find ./ \( -name "*.[chs]" -o -name "sysgen.py" -o -name "*.kconf" \) \
! -path "./host/src/genIdt/*" \
! -path "*/outdir/*" | xargs sed -i 's/\b'${1}'\b/'${2}'/g';
Change-Id: Ia8a93e07c88bbc559e7bbf0f14815e5e76110fb6
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Serial console handler when registered allows to interact with serial
line. It can either execute callback from ISR or defer execution to
fiber or task. This will be used in Bluetooth development for tests and
simple interaction with Bluetooth stack.
Change-Id: Ia960b456a75062d614baea324608058d979aa11b
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Since multi-node systems are not supported, the 'Srce' field now only serves
one purpose--to indicate whether the packet was allocated from the command
packet pool. As such, a better name (and type) for it is 'alloc' (of type
'bool') since 'Srce' (of type 'knode_t') suggest multi-node support.
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Change-Id: I47a935af13fd55dbca23c879841d68caf895eae4
Adding a line after variable declaration in order to comply with
the defined coding style.
Change-Id: Id41af88404bd37227bfd59a2d71ce08d0d6ce005
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Updating nano kernel functions to follow a consistent naming convention.
Part of that process is the removal of camelCase naming conventions for the
preferred_underscore_method.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find . -type f \( -iname \*.c -o -iname \*.h -o -iname \*.s -o -iname \*.kconf \) \
-not \( -path host/src/genIdt -prune \) \ \
-not \( -path host/src/gen_tables -prune \) \
-print | xargs sed -i "s/"${1}"/"${2}"/g"
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Updating nano kernel functions to follow a consistent naming convention.
Part of that process is the removal of camelCase naming conventions for the
preferred_underscore_method.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find . -type f \( -iname \*.c -o -iname \*.h -o -iname \*.s -o -iname \*.kconf \) \
-not \( -path host/src/genIdt -prune \) \ \
-not \( -path host/src/gen_tables -prune \) \
-print | xargs sed -i "s/"${1}"/"${2}"/g"
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Updating nano kernel functions to follow a consistent naming convention.
Part of that process is the removal of camelCase naming conventions for the
preferred_underscore_method.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find . -type f \( -iname \*.c -o -iname \*.h -o -iname \*.s -o -iname \*.kconf \) \
-not \( -path host/src/genIdt -prune \) \ \
-not \( -path host/src/gen_tables -prune \) \
-print | xargs sed -i "s/"${1}"/"${2}"/g"
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
Updating nano kernel functions to follow a consistent naming convention.
Part of that process is the removal of camelCase naming conventions for the
preferred_underscore_method.
Change accomplished with the following script:
#!/bin/bash
echo "Searching for ${1} to replace with ${2}"
find . -type f \( -iname \*.c -o -iname \*.h -o -iname \*.s -o -iname \*.kconf \) \
-not \( -path host/src/genIdt -prune \) \ \
-not \( -path host/src/gen_tables -prune \) \
-print | xargs sed -i "s/"${1}"/"${2}"/g"
Signed-off-by: Dan Kalowsky <daniel.kalowsky@intel.com>
