Defined struct in node rx for passing event parameters of
Advertising Set Terminated Event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implementation of Advertising Set Terminated Event on
duration sans use of additional variable in advertising
set context structure.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Updated implementation to have consistent initialization of
ret_cb use when passing it to ticker function calls.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
By splitting it out to a separate file, it will become easier to
separate generic and non-generic controller features.
This commit only contains the simple extraction.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Fixed memory corruption when using uninitialised previous
PDU to populate current PDUs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Enforce support for Read RSSI command if BT_CONN and BT_HCI_RAW are
selected. According to the Bluetooth specification, support for the
Read RSSI command is mandatory if the Connection State is
supported. BT_HCI_RAW indicates that the controller is an
independently qualifiable module and not part of a combined
host/controller build. This change avoids a configuration that cannot
be possibly qualified.
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Refactor implementation to perform enable and started state
updates at consistent places in code.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added implementation to acquire and initialize auxiliary
channel instance on use of periodic advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Enable Advertising Extensions by default if supported by the controller.
That is, do not enable it by default for BT_LL_SW_SPLIT.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Change sets default value of Kconfig option BT_CTLR_LLCP_CONN to
BT_MAX_CONN. The default value should properly handle the worst case.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Fix missing recalculation of skip value of the ticker being
inserted into ordered list, when it collides and is being
attempted to be inserted at next periodic interval.
This fix is for ticker compatibility mode which is used as
default for nRF51 series.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix flash operation timeout due to incorrect use of
secondary ticker to abort any radio in use. Ticker id 0
is reserved for split controller's pipeline preempt timeout.
Using the same ticker id caused the secondary ticker to
not be started if controller is using the same ticker id
for pipeline preempt timeout.
Fixes#26333.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix host RX thread being deadlocked. The deadlock occurs because the
RX thread is stuck waiting in conn_tx_alloc with K_FOREVER but if the
connection is disconnected only the RX thread can unblock it in the
handling of the disconnect event.
This commit fixes this deadlock by splitting the processing of the
disconnected event into two parts.
The part needed to unblock the RX is to release resources held by
unack'ed TX packets and mark the connection state as not connected
anymore.
The RX thread waiting for free_tx fifo and the TX thread waiting for
the bt_dev.le.pkts semaphore will both check the connected state after
having acquired them and will abort if disconnected.
The rest of the processing will be handled at normal RX thread
priority like normal.
Move the bt_recv_prio handling to the Bluetooth host when the host
has defined its own RX thread (CONFIG_BT_RECV_IS_RX_THREAD=n).
If the HCI driver has the RX thread (CONFIG_BT_RECV_IS_RX_THREAD=y),
then the responsibility to call bt_recv and bt_recv_prio correctly
falls to the HCI driver.
The helper function bt_hci_evt_is_prio() is replaced with
bt_hci_evt_get_flags() so that the HCI driver can do this correctly.
This decision to replace was made so that existing HCI drivers
maintained out-of-tree will fail at compile time with the new system.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bluetooth: host: Move bt_recv_prio to host when RX thread is defined
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix issue with directed advertiser not accepting connection request
from non-privacy enabled peer that has given us a non-zero IRK.
When device privacy is enabled then ull_filter_lll_rl_addr_allowed will
return true, and update the rl_idx to entry in the resolving list.
When the directed advertiser is not privacy enabled then lll->rl_idx is
set to FILTER_IDX_NONE and will not use RPA for the target address.
The check rl_idx != lll->rl_idx will then fail (0 != 0xff) and the
connect request is denied, even though all addresses matches on-air.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add explicit opcode check when handling received unknown
response PDU.
Without this, for example, an in progress Data Length Update
procedure state was reset when receiving an unknown response
to slave initiated feature request.
Fixes#26252.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Disable the controller advertising extension feature default setting
until the feature is complete. The zephyr host requires the
LE Advertising Set Terminated event to function.
Without this event a peripheral connection cannot pair because the
local on-air address is not set, and the advertising state will not be
cleaned up, so advertising cannot be started again.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use the NRF RNG entropy device as the entropy device for bt_rand and
controller internal functions when LLL is Nordic.
Using an entropy source with a significant increase in stack usage
will invalidate all stack size configurations in the system and lead
to stack overflow issues.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix compilation regression due to addition of const
qualifier to tx_pwr_lvl parameter of ll_tx_pwr_lvl_set
function. Support for BT_CTLR_TX_PWR_DYNAMIC_CONTROL
needs the tx_pwr_lvl to be updated and returned.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
For some reason GCC 9.x doesn't seem to be able to realize that set_num
will always be > 0 and so the local variable status will always be
initialized. Use a do {} while instead to keep it happy.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix missing implementation of initialization of common
advertising header bit fields when new auxiliary channel PDU
is instantiated. This caused corrupt invalid Bluetooth
Device address being copied from uninitialised previous
auxiliary PDU instead of copying from primary channel PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Review rework, added comments, TODOs, FIXMEs and converted
magic number use in advertising set state flags to defines.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added comments and code to make note that disabling all
advertising sets is not yet implemented.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
