Add information about how to build and test atsamr21_xpro board with
IEEE 802.15.4 RF2xx driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add special configuration for SAMR21 SoC. Since it have only 32k SRAM,
all possible application buffers need to be shrinked.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add information about how to build and test atsamr21_xpro board with
IEEE 802.15.4 RF2xx driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add special configuration for SAMR21 SoC. Since it have only 32k SRAM,
all possible application buffers need to be shrinked. This
configuration was tested with two boards for more than 2H with success.
[02:18:57.635,00] net_echo_server_sample: IPv6 UDP: Sent 333000 packets
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
UDP portion of the echo_client sends 1 packet with the sample data.
(TCP can send chunks of it depending on the response of the send()
function.) Not every network interface can send a UDP packet large
enough to handle the size of the sample data.
Let's make sure to account for the network interface MTU when deciding
the amount of sample data to send.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/22447
Signed-off-by: Michael Scott <mike@foundries.io>
Use new API to configure and interact with GPIOs. Move GPIO
initialization from sample into driver. The existing physical/line
level control has been kept rather than converting to logical level
signals.
Also improve error messages.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Eliminates CI build warnings such as this which breaks the build:
warning: NET_SOCKETS_POSIX_NAMES
(defined at subsys/net/lib/sockets/Kconfig:13) was assigned the value
'n' but got the value 'y'.
The testcase involves no offloading, which means it does not apply to
cc32xx.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
This PR eliminates the Kconfig warnings seen in build by setting the
options to the appropriate values for cc32xx platforms. They were
causing CI failures.
Fixes#22388
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Add Kconfig option NET_SAMPLE_SEND_ITERATIONS that sets the number of
times the Zephyr echo client sample sends its data. By default the
value is zero, which means indefinite, and demonstrates the same
behavior as before.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
This count is assigned to CONFIG_BT_ACL_RX_COUNT which expects a number
in the range of 1-64, otherwise kconfig fails.
Fixes#22259
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Switch to `NET_SOCKET_REGISTER` mechanism over the offloaded API
registration.
Including the following fixes from the review:
* The fd returned by the socket accept call needs to be finalized,
similar to how it is done for socket creation.
* sl_RecvFrom() in TI SimpleLink Host driver does not support NULL
pointers for 'from' address and address length, and sl_SendTo() does
not ignore the destination address when in connection mode, so passing
NULL would cause a failure. These issues have been reported to TI
(CC3X20SDK-1970, CC3X20SDK-1971).
Let's use sl_Recv and sl_Send to implement recvfrom/sendto in the case
of NULL addresses.
* simplelink_poll() should not process negative file descriptors in the
fds array after sl_Selecti() returns. A negative fd value indicates
that the entry is invalid and should be ignored.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Fixed bug in udp.c in echo_client and echo_server samples.
The bug causes UDP sockets to not close if socket id is 0.
Signed-off-by: Magne Værnes <magne.varnes@nordicsemi.no>
Make sure that the echo-server compiles ok if IPv6 or IPv4 is
disabled when VLAN is enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to better handle incoming data, wait() should return
the # of sockets with data returned by poll().
Based on this new return value, we can call mqtt_input() in a
smarter way.
Signed-off-by: Michael Scott <mike@foundries.io>
Now that mqtt_live() can send an EAGAIN message meaning: no ping
was generated, let's handle that in process_mqtt_and_sleep() by
skipping the call to mqtt_input() since no data will be expected.
Signed-off-by: Michael Scott <mike@foundries.io>
Make sure that we do not calculate terminating \n when comparing
the received data to sent data because the \n is not part of
the lorem_ipsum buffer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Sample app compiled with the GSM modem driver enabling PPP.
This sample was tested with a Reel Board UART_1 connected via the
external board/connector and a FONA 808 modem. Reel board specific
suppor is found in boards/.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Echo-server sample should not bail out on failed
accept() calls. This sample should close socket
in case of any errors and keep listening on socket
for further incoming connections.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Current sample certs and keys are not signed. Adding
signed certificates and keys. CA file also added.
This helps users to test with different kind of
configurations.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
A sample implementing NATS protocol that is not part of the Zephyr
networking subsystem. The implementation is not maintained and only
served as a proof of concept.
Related to #20017
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
`TLS_PEER_VERIFY` and `TLS_DTLS_ROLE` options accept specific values,
yet no symbols were defined for them. In result, magic numbers were used
in several places, making the code less readable.
Fix this issue, by adding the missing symbols to the `socket.h` header,
and using them in places where related socket options are set.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This add details how build and flash the application. This diferentiate
between SoC and transceivers to help understand what user need to do to
build and flash successfully.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Create overlay-rf2xx.conf overlay file to enable Atmel rf2xx
transceivers on this application.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
OpenThread settings implementation built on top of Zepyhr settings
submodule.
With this solution, OpenThread settings are identified with keys of
the following format: `ot/id/instance`, where `id` is assigned by
OpenThread stack, and `instance` is a 32-bit random number, both in
hex. The implementation makes use of `settings_load_subtree_direct`
function to iterate over settings instances. This allows the
OpenThread settings layer to be a fully transparent shim layer between
OpenThread/Zephyr APIs.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Define CONFIG_NET_CONFIG_IEEE802154_DEV_NAME value necessary to enable
atsamr21_xpro board on wpanusb sample.
The documentation was updated referencing the atsamr21_xpro board.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The $srctree environment variable is already set to point to the Zephyr
root, so no need to do
source "$(ZEPHYR_BASE)/Kconfig.zephyr"
in samples. Just
source "Kconfig.zephyr"
works.
(Things would break if $srctree was set to anything else, because every
'source' in the Kconfig files will be relative to it.)
Also add a 'mainmenu' title to the littlefs sample. It shows up at the
top of menuconfig/guiconfig. Source Kconfig.zephyr instead of Kconfig to
avoid overriding it.
As a sidenote, $(FOO) is better $FOO in Kconfig. $FOO is legacy syntax
that Kconfiglib only supports to be compatible with old Linux kernels.
$(FOO) uses the Kconfig preprocessor.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
x86-mmu now crashes with default 1K, bump to 2K, which hopefully might
work even for 64-bit archs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Include stdlib.h to suppress a missing declaration
warning for exit() when compiled as a Linux target.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Same deal as in commit bd6e04411e ("kconfig: Clean up header comments
and make them consistent") and commit 1f38ea77ba ("kconfig: Clean up
'config FOO' (two spaces) definitions"), for some newly-introduced
stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Allow to build also for general boards with supported ieee802154 and
usb, like reel_board, etc.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Create cc2520 overlay file. Can be used with:
cmake -DBOARD=quark_se_c1000_devboard \
-DOVERLAY_CONFIG=overlay-cc2520.conf ..
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This reverts commit da0f3311ff. It was
clearly intended to be a debugging aid when developing TCP2, not
intended for mainline. This fixes building this sample on POSIX
systems with Makefile.posix.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The sample needs key.c file but that cannot be generated by
sanitychecker. So disable compilation by sanitycheck.
Eventually we should make it possible to compile the sample
using some pre-defined values so that the sample will not
bit-rot but that is for later.
Fixes#21450
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
MQTT Azure and Google IoT samples are based on cloud
infrastructure. It would be nice to place all cloud
based samples in one single folder.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The application main() in Zephyr is defined as having a prototype:
void main(void), as expected by the kernel init (bg_thread_main).
So, correct the different samples and tests that were defined
otherwise.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This samples demonstrates how to connect to Azure Cloud
IoT hub which is based on MQTT protocol. User has to
create an account in Azure Cloud and provide those details
using Kconfig options. This sample first acquires DHCPv4
address and opens a secure connection with Azure cloud.
Then opens a MQTT connection and publish messages randomly.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The example should work on the cc3220sf_launchxl by following the same
flow as on other boards, ie. by connecting with plain http by default
and use TLS only when an overlay is specified. We update the
configuration for cc3220_launchxl to not use TLS by default and the
README to point users to the right overlay file to use.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
If we ran out of net_buf's while sending, ignore the issue
and try to finish the test instead. Solving the "running out
of network buffers" case would require careful tuning of
number of network buffers, buffer size, upload speed etc. which
is difficult to solve with generic buffer count options.
The user should tweak mainly the CONFIG_NET_BUF_TX_COUNT option.
Optionally CONFIG_NET_PKT_TX_COUNT can be changed too. Information
about these options is printed to console after the test is finished.
Fixes#20315
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add "sample quit" shell command which can be used to stop the
sample application and allows the generation of coverage report.
Fixes#21099
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The definition was removed in commit 7ccc7889fa ("logging: Remove
SYS_LOG implementation").
Adding detection of unused symbols in samples and tests to CI.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
echo_client and echo_server configuration for 802.15.4 and OpenThread is
covered by overlay files and default board configuration. Board-specific
configuration for frdm_kw41z was redundant in this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
For some reasons SOC_SERIES_SAME70 was selected in civetweb sample,
which prevents build on other platforms.
This issue was silent since sample yaml file limits sample testing on
sam_e70_xplained.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
echo_server crashes if the coverage is enabled due to the insufficient
stack size.
Use bigger stack size when the coverage is enabled.
Fixes#20797
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Several macros were documented as deprecated but lacked the
infrastructure to produce deprecation warnings. Add the deprecation
marker, and fix the in-tree references to the deprecated spellings.
Note that one non-deprecated macro should have been deprecated, and
is, referring to a newly added line control bit.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
As the iPerf2 protocol is not documented properly, depend on
exact iPerf 2.0.5 version when testing.
Fixes#20313
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Quit the accept loop if there is a socket related error as there
is no point of continuing in this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
PSK support is added to echo-client.c and echo-server.c.
If enabled, a header is included which contains the PSK.
If the default dummy PSK header is used, a warning is issued.
The header can be changed via Kconfig.
Signed-off-by: Torstein Grindvik <torstein.grindvik@nordicsemi.no>
Not a top-level zephyr core API and tied to third party environment, so
move it to where the code is in lib/updatehub.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There are two set of code supporting x86_64: x86_64 using x32 ABI,
and x86 long mode, and this consolidates both into one x86_64
architecture and SoC supporting truly 64-bit mode.
() Removes the x86_64:x32 architecture and SoC, and replaces
them with the existing x86 long mode arch and SoC.
() Replace qemu_x86_64 with qemu_x86_long as qemu_x86_64.
() Updates samples and tests to remove reference to
qemu_x86_long.
() Renames CONFIG_X86_LONGMODE to CONFIG_X86_64.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
In order to be able to run the sanity check, don't open the socket
if the test protocol is enabled.
Also add a debug print at the recv().
This commit will be dropped:
- As soon as the sanity check site accomodates
- As soon as the integration is complete
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
This adds a multithreaded dumb HTTP server sample application similar
to dumb_http_server with following differences
* support both IPv4 and IPv6 simultaneously
* support multiple incoming connections
* support TLS connections
* ignore POSIX compatibility
This app can be used for testing. Note that the app will always
serve a same static HTML page to caller regardless of HTTP request
parameters.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of the socket samples had wrong information about what default
board to use. Currently there is no default board and user must
select the board when building the application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Instead of printk(), use logging macros so that all the output
from IP stack and sample is nicely interleaved.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Network shell is useful to have in order to debug things so
enabling it for this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adds zero configuration based on LLMNR. This should be working in
Windows out of the box, zephyr can be accessed with http://zephyr/.
Can be combined with netusb configuration (RNDIS is supported in
Windows).
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
By default only one listener is enabled, but if user specifies
CONFIG_NET_SAMPLE_NUM_HANDLERS with value larger than 1, then
multiple threads are created, and each will be able to accept
connections.
Fixes#19374
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
PR #18780 introduces a way to decouple pthread support from the general
CONFIG_POSIX_API global switch. This commit modifies the build of
SimpleLink components to take advantage of it, since SimpleLink
libraries only require pthread, sem, clock, and sleep support, not
entire POSIX API.
This fixes the build errors in the http_get sample introduced
by the merge of #18736. As such, this patch also removes
cc3220sf_launchxl exclude from sample.yaml of that sample.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Now that we have support for properly combine conditions from multiple
"filter" clauses in one sample.yaml file (e.g. from "common" and
test-specific sections), use it instead of previous adhoc syntax
relying on string concatenation.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add some mbedTLS tweaks for OpenThread in overlay-ot.conf.
Add sample configuration to enable Commissioner/Joiner, disabled by
default.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Build errors were introduced by the merge of #18736. Until PR #18780 is
approved to allow the SimpleLink libraries to build without
CONFIG_POSIX_API, this patch excludes cc3235sf_launchxl from the test
build.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
While trying out the hello_world sample built for QEMU, I was expecting
the sample app to exit and I'd return to a command prompt. Nope. You
need to exit QEMU manually, so add that step to the sample instructions.
Looking around, there are more uses of QEMU like this that could use
this added step after running the sample app.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
With CONFIG_POSIX_API enabled, these samples now build under Zephyr
with exactly the same source as e.g. Linux (or in general, other POSIX
systems). However, building without CONFIG_POSIX_API (i.e. with
CONFIG_NET_SOCKETS_POSIX_NAMES aux option) is retained for now.
Add testcase definitions to build these samples with CONFIG_POSIX_API
in CI.
Fixes: #17353
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If mDNS is enabled, then do the mDNS query always. Earlier we did
the query after we had received response to the normal DNS query.
Also there is no need to print DNS id for mDNS queries as the id
is always 0.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We do not need the return values from various calls to pthread_*()
functions.
Coverity-CID: 203462
Coverity-CID: 203535
Fixes#18376Fixes#18377
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When LWM2M_RD_CLIENT_SUPPORT_BOOTSTRAP is enabled:
- Mark the first server as a bootstrap server
- Create second server and security instances (used by bootstrap
server)
This allows bootstrap support to be tested out of the box with
the following:
- setup Leshan bss-server-demo (bootstrap server) on port 5783
- setup Leshan server-demo (lwm2m server) on port 5683
- add an entry into the bootstrap server:
LWM2M Server=coap://[2001:db8::2]:5683
- build the sample like so:
west build -t run -b qemu_x86 \
-s zephyr/samples/net/lwm2m_client/ -- \
-DCONFIG_LWM2M_RD_CLIENT_SUPPORT_BOOTSTRAP=y \
-DCONFIG_LWM2M_PEER_PORT=5783
Signed-off-by: Michael Scott <mike@foundries.io>
CONFIG_NET_SOCKETS_POSIX_NAMES is incompatible with POSIX_API, so it's
disabled by the build system. It's no longer required anyway.
It is a leftover from before #16557 was merged.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
SOCKS5 support added to echo_client. Details are added
in README file about how to verify this feature using
echo-client with echo-server running on Linux host.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This commit adds a sample configuration for 6LoCAN to the
echo_client and echo_server example.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit is an implementation of 6LoCAN, a 6Lo adaption layer for
Controller Area Networks. 6LoCAN is not yet standardised.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Modify mqtt_publisher sample to use mqtt_client_set_proxy().
Removed CONFIG_MQTT_LIB_SOCKS based setup.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Let's add support for recently added LwM2M objects:
- Connectitiy Monitoring
- Location
- IPSO Accelerometer
- IPSO Buzzer
- IPSO On/Off Switch
- IPSO Push Button
Currently, this is limited to compile enabled and manual creation
of objects via LwM2M server. Objects will respond to read/write
operations, but not have real HW backing.
Signed-off-by: Michael Scott <mike@foundries.io>
LwM2M allows for multiple instance resources such the power source
resources in the device object. These types of resources have
always been very hard to work with, and frankly were poorly
implemented.
This led to other issues where it was very hard to have
non-sequential resource instances, and each resource of this type
needed special getter / setter methods such as:
lwm2m_device_add_pwrsrc()
lwm2m_device_set_pwrsrc_voltage_mv()
Going forward, as more LwM2M objects are implemented this just
doesn't scale well.
To fix this:
- split the resource instance data out from the resource data.
This includes the data pointer information and resource
instance id.
- add resource id and resource instance id to the event callback
functions so user's can see in more detail what resources and
resource instances are being handled.
- allow generic functions like lwm2m_engine_get_*() and
lwm2m_engine_set_*() to access resource instance data.
- adjust object resource initialization macros to map resource
instances to resources at the time of object instance
creation.
- fix up the lwm2m_client as a reflection of all of these changes.
Signed-off-by: Michael Scott <mike@foundries.io>
By sending the temp value back to the LwM2M engine, it allows all of
the min/max values to be updated over time.
Fixes an issue where min/max values were not being updated.
Signed-off-by: Michael Scott <mike@foundries.io>
The native Zephyr LwM2M client enables the JSON formatter which
can use more of the packet buffers than the default 256 with
TLV formatting. Let's set the default to 512 in order to avoid
cutting off the output of larger READ operations.
In the future, we should establish block transfer buffers to
handler longer READ ops.
Signed-off-by: Michael Scott <mike@foundries.io>
Per IPSO Light Control definition from the OMA LwM2M registry:
http://www.openmobilealliance.org/tech/profiles/lwm2m/3311.xml
There is an optional "Application Type" string resource (5750) in the
Light Control object. This was missed in the initial implementation.
NOTE: sample will assign reference if needed.
Signed-off-by: Michael Scott <mike@foundries.io>
We are pre-allocating a storage variable for the application type
resource in the IPSO Timer object. This is an optional resource
which won't always be set by samples.
Let's leave out the pre-allocated variable and let the sample set
this reference if needed (it's optional).
Signed-off-by: Michael Scott <mike@foundries.io>
Now that strcspn() is implemented in our minimal libc, remove it from
the civetweb sample to avoid the linker complaining about multiple
definitions.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds civetweb as a west module and a sample that uses it.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The `start_udp_and_tcp` funcion is a blocking function, therefore it
should not be called from the system workqueue, as it would stall it.
Because it was called in such a way, the retry mechanism, which
also relied on the system workqueue did not work properly.
This commit fixes the issue, by keeping the main application processing
in the main thread, and using a semaphore to synchronize with the
connection manager.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Sample applications for display functions do not work on native_posix_64
due to missing overrides. Clone the native_posix_64 Kconfig override
for all samples that have a native_posix Kconfig override.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Remove old configurations of boards that do not support networking
natively and very custom and difficult to test.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Start to monitor Connected and Disconnect events and then start
and stop the echo service according to system connectivity status.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The size_t type is either compatible with an int on 32-bit target, or
a long on 64-bit targets. It could even be a long even on some 32-bit
targets. Let's use the z qualifier in the printf format to be compatible
with whatever flavor in use.
In case of pointers, let's just use %p with pointers directly and
avoid casts altogether.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Converts all net samples that enable the mcr20a 802.15.4 driver to use
the frdm_cr20a shield instead of hardcoding configs for the frdm_k64f
base board. This makes it possible to build mcr20a samples for other
base boards with compatible arduino headers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If a sample wants to use the Zephyr implementation of mbedtls, it
enables CONFIG_MBEDTLS and sets any needed Zephyr-specific mbedtls
options.
Currently, the LwM2M subsystem selects MBEDTLS automatically when
LWM2M_DTLS_SUPPORT is enabled. Let's remove this and let the
LwM2M client sample enable mbedtls and it's options.
This mimics the behavior of several other network-related samples
and removes conflicts when selecting alternate implementations of
MBEDTLS.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/17399
Signed-off-by: Michael Scott <mike@foundries.io>
If user has set CONFIG_NET_CONTEXT_TIMESTAMP then enable
network packet throughput collection for UDP packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We use the following commands to rename any
LED._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_LED._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l LED._GPIO_CONTROLLER | xargs sed -i 's/LED\(.\)_GPIO_CONTROLLER/DT_ALIAS_LED\1_GPIOS_CONTROLLER/g'
git grep -l LED._GPIO_PIN | xargs sed -i 's/LED\(.\)_GPIO_PIN/DT_ALIAS_LED\1_GPIOS_PIN/g'
git grep -l LED._GPIO_FLAGS | xargs sed -i 's/LED\(.\)_GPIO_FLAGS/DT_ALIAS_LED\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>